r45270 removed ieee80211n=%d from the format string but didn't remove
the parameter itself. Though this probably doesn't cause any harm, it's
quite confusing and unneeded.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45351
To enable 802.11r, wpa_key_mgmt should contain FT-EAP or FT-PSK. Allow
multiple key management algorithms to make this possible.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 45050
The 802.11r implementation in hostapd uses nas_identifier as PMK-R0 Key
Holder identifier. As 802.11r can also be used with WPA Personal, nasid
should be appended to the hostapd config for all WPA types.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 45049
'hostapd-common' is needed by all of the variants for wifi to function
correctly (a number of the target profiles simply select 'wpad-mini').
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 45048
These new variants include support for mesh mode and SAE crypto.
They always depend on openssl as EC operations are not provided by
the internal crypto implementation.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45047
madwifi was dropped upstream, can't find it anywhere in OpenWrt
either, thus finally burrying madwifi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45045
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.
This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).
This is especially useful if an OpenWrt device with two radios is used to
retransmit the same network (one in AP mode for other clients, one as STA for
the uplink); the following configuration prevents the device from associating
with itself, given that the own AP to be avoided is using the bssid
'C0:FF:EE:D0:0D:42':
config wifi-iface
option device 'radio2'
option network 'uplink'
option mode 'sta'
option ssid 'MyNetwork'
option encryption 'none'
list bssid_blacklist 'C0:FF:EE:D0:0D:42/00:FF:FF:FF:FF:FF'
This change consists of the following cherry-picked upstream commits:
b3d6a0a8259002448a29f14855d58fe0a624ab76
b83e455451a875ba233b3b8ac29aff8b62f064f2
79cd993a623e101952b81fa6a29c674cd858504f
(squashed to implement bssid_{white,black}lists)
0047306bc9ab7d46e8cc22ff9a3e876c47626473
(Add os_snprintf_error() helper)
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 44438
Introduce configuration options to build an "hardened" OpenWRT.
Options to enable Stack-Smashing Protection, FORTIFY_SOURCE and RELRO
have been introduced.
uClibc makefile now automatically detects if SSP support is necessary.
hostapd makefile has been fixed to use "^" as sed separator since
using a comma was problematic when using "-Wl,-z,now" and the like in
TARGET_CFLAGS.
Currently enabling SSP on user space depends on enabling SSP kernel
side, this is due to the fact that TARGET_CFLAGS are used to build
kernel modules (at least). Suggestions on how to avoid this are welcome.
Using "select" instead of "depends on" doesn't seem to work with choice
entries.
Tested with a lantiq (WBMR) router, GCC 4.8, uClibc and a subset of
the available packages.
Needs to be tested with GCC 4.9 and the remaining packages.
PIE not currently included.
Signed-off-by: Alessandro Di Federico <ale+owrt@clearmind.me>
SVN-Revision: 44005
This patch fixes adding new stations for some specific drivers when
using more than 1 BSS.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43951
The uapsd option sets the uapsd_advertisement_enabled flag in hostapd.
The check for phy support is already implemented here in hostapd since 2011:
http://w1.fi/cgit/hostap/commit/?id=70619a5d8a3d32faa43d66bcb1b670cacf0c243e
So this can be safely set to 1 as default.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43846
In r41872 and r42787 Dynamic VLAN support was reintroduced, but the vlan_bridge
parameter is not read while setting up the config, so the default is used which
is undesirable for some uses.
Signed-off-by: Ben Franske <ben.mm@franske.com>
SVN-Revision: 43473
Note, that licensing stuff is a nightmare: many packages does not clearly
state their licenses, and often multiple source files are simply copied
together - each with different licensing information in the file headers.
I tried hard to ensure, that the license information extracted into the OpenWRT's
makefiles fit the "spirit" of the packages, e.g. such small packages which
come without a dedicated source archive "inherites" the OpenWRT's own license
in my opinion.
However, I can not garantee that I always picked the correct information
and/or did not miss license information.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 43155
The wpa_psk_file option offers the possibility to use a different WPA-PSK key for each client. The directive points to a file with the following syntax:
mac_address wpa_passphrase_or_hex_key
Example:
00:11:22:33:44:55 passphrase_for_client_1
00:11:22:33:44:67 passphrase_for_client_2
00:11:22:33:44:89 0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef
So it is possible to specify both ASCII passphrases and raw 64-chars hex keys.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43001
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
In r41872 Dynamic VLAN support was reintroduced, but the vlan_naming
parameter is not read while setting up the config, so it always
defaults to 1.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 42787
With this patch WPS discovery can be started or canceled over ubus if
WPS is enabled in wireless configuration. This is equivalent of
'hostapd_cli wps_pbc' and 'hostapd_cli wps_cancel' commands.
Signed-off-by: Petar Koretic <petar.koretic@sartura.hr>
SVN-Revision: 42459
This patch brings full dynamic vlan support to netifd that existed in hostapd.sh in Attitude Adjustment.
Signed-off-by: Joseph CG Walker <Joe@ChubbyPenguin.net>
[jow@openwrt.org: changed commit message, rebased on top of current hostapd.sh]
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41872
Fixed wpa_supplicant when the radio is in 40MHz mode so that it no
longer restarts hostapd with the second channel disabled.
Signed-off-by: Lance Chaney <furryfur1@gmail.com>
SVN-Revision: 41019
