Commit graph

41014 commits

Author SHA1 Message Date
Tim Harvey
ef627cb0f5 octeontx: add fpu support
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey
10280d9e22 octeontx: remove CFLAGS
You should not define CFLAGS for the toolchain as this will also leak
into other targets if they share the same toolchain.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey
c0470e7917 octeontx: add FAT FS support to kernel
The CN80XX Boot firmware uses an embedded FAT12 filesystem. For some reason
busybox can't mount this unless its enabled static in the kernel.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey
4294b79e0a octeontx: add USB_PCI support
The CN80XX XHCI is supported through PCI

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Koen Vandeputte
efb362cd93 imx6: disable dma on uart
When this target got updated to 4.14, this patch got removed to
re-evaluate if it was still needed.

Extensive testing now shows this issue is still present.
Let's re-add the patch to fix it for now.

As the uart bus is very low bandwidth .. performance impact is negligible.

Boot log:

[   22.513051] imx-uart 2020000.serial: DMA transaction error.
[   22.522721] imx-uart 2020000.serial: DMA transaction error.

As a sidenote:
The patch mentiones an issue with RS485, but the bootlog
errors above were recorded with the uart ports in standard RS232 mode.

Compile/Run-tested on imx6/GW5200

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-22 12:46:49 +01:00
Koen Vandeputte
aad1f11efe kernel: refresh patches
Some fuzz was introduced due to the netfilter-offload series

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-22 12:46:25 +01:00
Felix Fietkau
14a01311f5 kernel: remove kmod-appletalk
This has been obsolete for many years now and has been implicated in a
recent build failure

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-22 12:08:38 +01:00
Felix Fietkau
ecd810d0f5 kernel: fix kernel module packaging errors on imx6
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-22 11:58:00 +01:00
Felix Fietkau
1b13cbc15b grub2: disable building platform code for target utility
It is not used and it was causing a build error with GCC 7.3

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-22 09:30:22 +01:00
Felix Fietkau
7a97588bc6 toolchain/gcc: use version 7.x for x86 by default
This is needed for retpoline support, which mitigates the spectre
attacks.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:57:30 +01:00
Felix Fietkau
65ae02d602 toolchain/gcc: remove unused config symbol
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:57:24 +01:00
Felix Fietkau
9d2a23780e kernel: avoid stripping retpoline flag with CONFIG_MODULE_STRIPPED
Fixes kernel warning when loading modules

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:55:52 +01:00
Felix Fietkau
820f030998 netfilter: add a xt_FLOWOFFLOAD target for NAT/routing offload support
This makes it possible to add an iptables rule that offloads routing/NAT
packet processing to a software fast path. This fast path is much
quicker than running packets through the regular tables/chains.

Requires Linux 4.14

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:42 +01:00
Felix Fietkau
1033356442 kernel: backport netfilter NAT offload support to 4.14
This only works with nftables for now, iptables support will be added
later. Includes a number of related upstream nftables improvements to
simplify backporting follow-up changes

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:42 +01:00
Felix Fietkau
b7265c59ab kernel: backport a series of netfilter cleanup patches to 4.14
Preparation for backporting upstream NAT offload support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:42 +01:00
Felix Fietkau
bc3e0f6052 nftables: update to 0.8.2, backport flowtable support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:41 +01:00
Felix Fietkau
8cdc71fc92 libnftnl: backport flowtable support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:41 +01:00
Felix Fietkau
c8d07575e5 mac80211: add minstrel improvements/fixes
- Simplify debugfs code
- Reduce size
- Fix handling of CCK rates

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:29:33 +01:00
Felix Fietkau
981cca12b6 hostapd: add support for sending 802.11v disassoc imminent notifications to clients via ubus
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:29:09 +01:00
Felix Fietkau
01b2c0fc49 hostapd: add support for issuing 802.11k beacon measurement requests via ubus
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:29:04 +01:00
Felix Fietkau
21bb42fb8a hostapd: expose client 802.11k capabilities via ubus
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:28:59 +01:00
Nick Hainke
e2681eb06a hostapd: return with 80211 codes in handle event function
If the auth or assoc request was denied the reason
was always WLAN_STATUS_UNSPECIFIED_FAILURE.
That's why for example the wpa supplicant was always
trying to reconnect to the AP.
Now it's possible to give reasoncodes why the auth
or assoc was denied.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2018-02-21 19:28:56 +01:00
Lorenzo Santina
83b4fa9b3b hostapd: add IEEE 802.11v support
Add Wireless Network Management (IEEE 802.11v)
support to:
- hostapd-full
- wpa_supplicant-full

It must be enabled at runtime via UCI with:
- option ieee80211v '1'

Add UCI support for:
- time_advertisement
- time_zone
- wnm_sleep_mode
- bss_transition

Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
2018-02-21 19:28:50 +01:00
Felix Fietkau
6b1816f8a3 hostapd: add support for turning on 802.11k/v features via ubus
Neighbor reports are enabled implicitly on use, beacon reports and BSS
transition management need to be enabled explicitly

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:28:43 +01:00
Felix Fietkau
526921f20e mac80211: round up tx status headroom
Fixes unaligned access exceptions in mt76 when transmitting beacons

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:28:36 +01:00
Felix Fietkau
8a59f9590e ramips: fix MT7621 switch driver IRQ storm on init with linux 4.14
The hardware emits some interrupts while initializing and handling them
can mess up the state or cause infinite loops.
Fix this by disabling IRQs during init and re-enabling them afterwards

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 14:46:45 +01:00
Felix Fietkau
0405205140 kernel: fix MIPS GIC clock source counter width (affects MT7621)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 14:46:45 +01:00
Felix Fietkau
79f9cadd00 ramips: fix MT7621 PCI driver on 4.14
The .map_irq hook can now be called after init.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 14:46:45 +01:00
Felix Fietkau
9595a9e8d3 kernel: fix return value of usb_xhci_needs_pci_reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-20 22:29:32 +01:00
Felix Fietkau
c38fb58576 kernel: fix disabling common usb quirks on 4.14
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-20 22:19:41 +01:00
John Crispin
3cb38368e2 ubox: fix PKG_MIRROR_HASH
Signed-off-by: John Crispin <john@phrozen.org>
2018-02-20 21:35:14 +01:00
INAGAKI Hiroshi
e1d4aa36b0 ramips: add support for Tama W06
Tama Electric Axing W06 is a 2.4 GHz band 11n router, based on Mediatek
MT7688AN.

Specification:

- MT7688AN (575 MHz)
- 64 MB of RAM (DDR2 SDRAM)
- 16 MB of Flash (SPI)
- 1T1R 2.4 GHz
- 1x 10/100/1000 Mbps Ethernet
- 4x LEDs (GPIO connected: 3), 1x button
- 1x USB 2.0 Type-A (host)
- UART header on PCB (GND, RX, TX, Vcc from RJ45 side)

Flash instruction using sysupgrade image:
1. Connect micro-USB cable for power supply into W06 and turn on the
router
2. Connect to wifi with SSID "tama-*" with password. Complete SSID and
password are listed on the back of the router
3. Access to 192.168.1.1 and login with user name "admin" and password
empty
4. In firmware update(ファームウェア更新) page, click "参照" button
and click "ブラウザー" button to open file browser, select the
sysupgrade image and press OK button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-02-20 19:25:17 +01:00
Mathias Kresin
cb741654e5 ramips: improve GnuBee Personal Cloud Two support
Use the generic board detection for the GnuBee Personal Cloud Two
instead of the target specific one as all recent additions are doing.

Fixup the pinmux to set all pins used as GPIO to the function GPIO.
Request pins where used.

Drop the i2c from the dts. There is nothing connected. While at it fix an
indentation issue and use references instead of duplicating the whole
node path.

Use the same switch config as for the GB-PC1 and drop the led trigger for
the not supported IP1001 phy connected to second rgmii.

Fixes: c60a21532b ("ramips: Add support for the GnuBee Personal Cloud Two")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
c330408ea9 ramips: use generic board detection for D-Link DAP-1522 A1
Use the generic board detection for the D-Link DAP-1522 A1 instead of the
target specific one as all recent additions are doing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Hauke Mehrtens
6eaf8b3d89 lantiq: kernel 4.14: update dts files
Updated the devicetree source files to make use of the following
upstreamed drivers:

 - xrx200 ethernet phy
 - reset controller unit
 - dwc2
 - fpi

Use our custom xrx200 ethernet phy compatible to support boards, which
have switched the vr9 revision during lifetime, with a single devicetree
source file.

By switching to the dwc2 driver + usb phy framework, we don't need to used
our custom gpio power patch and can use a fixed regulator instead.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
f519fea4c6 lantiq: kernel 4.14: cleanup dts files
Move common used parts to dtsi. Add labels to nodes and reference nodes
via labels in dts files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
82ae68be70 lantiq: kernel 4.14: fix usb
On danube the USB0 registers are at 1e101000 similar to all other lantiq
SoCs.

On Danube and AR9 the USB core is connected to the AHB bus, hence we need
to enable the AHB Bus as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
2368f7cb78 lantiq: kernel 4.14: autoselect matching vr9 rev firmware
Add a custom xrx200 ethernet phy compatible to load the firmware matching
the vr9 revision without specifing an expected revision.

We have quite a few boards in the tree were later produced ones are using
a more recent vr9. It is impossible to distinguish which revision of the
vr9 is used without opening the case and removing a heatsink for some of
them.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
a48b4ae38b lantiq: kernel 4.14: don't use CPU interrupt controller IPI IRQ domain support
This reverts kernel commit 1eed40043579 ("MIPS: smp-mt: Use CPU interrupt
controller IPI IRQ domain support"). With the patch applied, the kernel
hangs during boot if SMP is active.

The Lantiq IRQ controller gets registered first and it directly handles
the MIPS native SW1/2 and HW0 - HW5 IRQs. It looks like this controller
already registers IRQ 0 - 7 and the generic driver only gets the following
IRQs starting later.

The upstream discussion can be found at
https://www.linux-mips.org/archives/linux-mips/2017-05/msg00059.html.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
cf53f2180c lantiq: kernel 4.14: select MFD SYSCON for ase
Enable syscon to use it for the RCU MFD on Amazon SE as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Hauke Mehrtens
f1d84023cb lantiq: kernel 4.14: update patches and config
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Hauke Mehrtens
5eeaba31b8 lantiq: kernel 4.14: copy patches, config and dts files
This just copies the patches, configuration and dts files into the
directories hich are used for kernel 4.14.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-20 19:25:17 +01:00
Hauke Mehrtens
73ba5e11f7 lantiq: fix lantiq applications kernel 4.14 compatiblity
This is fixing multiple compile problems with kernel 4.14 and updates the
code to take care of changes introduced between kernel 4.9 and 4.14.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
f8a6987cd1 lantiq: make dts files and kernel config kernel version specific
Move the devicetree source files to a kernel specific directory in
preparation of adding kernel 4.14 support.

Rename the subtarget kernel config files to match a specific kernel
version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
627a28eb09 lantiq: rename gphy firmware
Rename the gphy firmware to match the name requested by kernel 4.14 and
update the devicetree source files to use the new name.

Update the u-boot lantiq Makefile to be compatible with the new names as
well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
6112abf186 kernel: enable CONFIG_USB_PCI for PCI usb modules
With upstream commit 2c93e790e825 ("usb: add CONFIG_USB_PCI for system
have both PCI HW and non-PCI based USB HW") the CONFIG_USB_PCI was
introduced.

The option is disabled by default in our generic kernel 4.14 config, hence
we need to set the option for all related kernel modules.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
04cb1e0fd2 ppp: fix build with kernel 4.14.9+
With a9772285a724 ("linux/compiler.h: Split into compiler.h and
compiler_types.h") compiler.h was refactored and most its content was
moved to compiler_types.h. Both files are required to build ppp-mod-pppoa.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Hans Dedecker
97c27f01be odhcpd: fix interop with wide DHCPv6 client (FS#1377)
96033e9 dhcpv6-ia: don't always send reconf accept option (FS#1377)

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-02-20 16:30:15 +01:00
Zoltan HERPAI
d2ac070552 modules: iio-mxs-lradc: build on mxs only
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-02-20 15:03:12 +01:00
Zoltan HERPAI
5360441d8f modules: gpio-mcp23s08: fully depend on i2c-core
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-02-20 14:13:20 +01:00