Commit graph

19358 commits

Author SHA1 Message Date
Kristian Evensen
8f9baf5e1a x86: Add APU3 reference to x86 board.d
There is a new APU-model available, APU3. The device is configured in
the same way as the APU1 and APU2, so the same LED/network setup can be
used.

I considered changing the case to pc-engines-apu*, but I chose to follow
the existing pattern and add the full board name.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2018-05-18 09:17:24 +02:00
Christian Lamparter
16e39624b7 apm821xx: backport and reassign crypto4xx patches
This patch backports several patches that went upstream into
Herbert Xu's cryptodev-2.6 tree:

crypto: Use zeroing memory allocator instead of allocator/memset
crypto: crypto4xx - performance optimizations
crypto: crypto4xx - convert to skcipher
crypto: crypto4xx - avoid VLA use
crypto: crypto4xx - add aes-ctr support
crypto: crypto4xx - properly set IV after de- and encrypt
crypto: crypto4xx - extend aead fallback checks
crypto: crypto4xx - put temporary dst sg into request ctx

The older, outstanding patches from 120-wxyz series have been
upstreamed as well and therefore they have been reassigned to
fit into the series.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-05-18 09:14:09 +02:00
Christian Lamparter
e6e51ce87f apm821xx: don't select swconfig for the MR24
The swconfig package is part of the DEFAULT_PACKAGES list in
the apm821xx's nand subtarget. It's enabled by default because
the MX60(W) and WNDR4700 need it for their initramfs. However
the package is not necessary for the MR24's sysupgrade image, as
the MR24 does not have a switch.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-05-18 09:13:19 +02:00
Roman Yeryomin
1f42deec8e ipq40xx: fix ethernet on ap-dk01.1
Not sure how it worked before but ethernet is disabled
by default in ipq4019 dtsi.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-18 09:12:53 +02:00
Koen Vandeputte
e2aa0c3f8b kernel: bump 4.14 to 4.14.41
Refreshed all patches

Dropped upstreamed patches:
522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch
523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch
525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch
527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch

updated patches:
524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch
030-USB-serial-option-fix-dwm-158-3g-modem-interface.patch

Added new ARM64 symbol: CONFIG_ARM64_ERRATUM_1024718

Compile-tested on: cns3xxx, imx6, mvebu (arm64), x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-05-18 09:10:46 +02:00
Koen Vandeputte
12f44b83a8 kernel: bump 4.9 to 4.9.100
Refreshed all patches

Added new ARM64 symbol: ARM64_ERRATUM_1024718

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-05-18 09:10:21 +02:00
Daniel Gonzalez Cabanelas
fbbb977772 brcm63xx: Tune the network configuration for several routers
- DGND3700v1: fix port numbers, they're in reverse order
- FaST2704n: there is no WAN port identified as such, only 4 LAN
- AD1018: configure the "FIBRE" port as WAN

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2018-05-18 08:55:37 +02:00
Rosen Penev
fec205f654 ramips: mmc: Sync with staging driver
Mostly whitespace cleanups. Some unneeded code was removed.

MMC init was also moved to the probe function as in
6069bdd

The cleanup commits are over 100, making it hard to do them individually.

Tested on GnuBee PC1 with an SD card being used as swap.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
v2: Fixed compile issue with mt7620
2018-05-18 08:49:52 +02:00
Matthias Schiffer
a5b77c9d9d
ath79: remove unused copy-file build step
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-05-17 22:11:56 +02:00
Matthias Schiffer
aea146736c
ath79: fix TP-Link TL-WR1043ND v1 image build
Both initramfs and flashed images are built and boot. No Ethernet, no WLAN,
probably further issues, so the image is not added to TARGET_DEVICES for
now.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-05-17 22:11:56 +02:00
Felix Fietkau
e9cb1b720d netfilter: fix hardware offload regression (FS#1551)
The relevant code needs to be enabled even if flow table support is only
compiled as module

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-17 08:21:54 +02:00
Mathias Kresin
75ed56a08a ath79: add AVM FRITZ!WLAN Repeater 300E
No known issues, everything works fine.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
bc04cf780e ath79: ar724x: fix pll settings
Add the syscon compatible, otherwise used functions like
syscon_regmap_lookup_by_phandle() will return an error and setting the
ethernet pll data wont work at all.

Fix the pll register width. Writing to registers out of the range via
syscon isn't possible and returns an error. On ar7242 the last pll
register - Current Audio Modulation Logic Output - is at 0x1805003c.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
f7ec385c13 ath79: add and enforce image metadata
Add metadata to images and make the metdata mandatory.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
f77db1a590 ath79: cleanup image build code
Remove recipes for not yet migrated boards. Drop variables which aren't
required due to the switch to devicetree like boardname.

Drop the legacy image build code. Boards added to this target shouldn't
use the legacy image build code anyway.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
cfe442c503 ath79: sysupgrade: drop unused variables
None of the variables are used at the moment.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
3e9d9f6225 ath79: sysupgrade: drop unused platform checks
None of these checks are used at the moment and most of them aren't
required if the image metadata validation is used.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
377197fdb3 ath79: sysupgrade: remove obsolete sysupgrade watchdog kill
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
0ff5785c5d ath79: fix dts files
Add the SoC compatible to the individual dts files. Rename the dts files
to match the common pattern.

Remove dts files wich aren't used and no image in ar71xx exists.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
8f7e28a783 ath79: enable wireless
PCI attached wireless works fine. So enable the wireless config symbols.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
bf781bd2ef ath79: cleanup kernel config
Remove outdated or not required kernel config settings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
b2cef5d045 ath79: drop platform data patches
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
a181781bf8 octeontx: make board.d files executable
Add the executable permission to the files to ensure they run on
firstboot.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
d136192396 ath79: make board.d files executable
Add the executable permission to the files to ensure they run on
firstboot.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
d8b475212b lantiq: kernel 4.14: use vbus-supply devicetree property
It isn't a phy supply, as the phy is still up if the GPIO is low. It
rather is the supply for the vbus. A correct setting/definition will be
relevant as soon as USB peripheral mode is supported.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
0e9e8d8323 kernel: dwc2: add support for host mode external vbus supply
Backport patch adding support for the vbus-supply devicetree property,
which allows to specific GPIOs (via fixed regulators) to enable
vbus/usb power.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
0b62fe5ed8 lantiq: complete AVM FRITZ!Box 3370 support
Rename the image and use a compatible string which indicates that only
hardware revision 2 and higher is supported.

It allows to use the wireless LED, as HWRev 1 uses GPIO#39 for the
wireless LED and starting with HWRev 2 GPIO#35 is used for the wireless
LED and GPIO#39 for IFX_GPIO_MODULE_EXTPHY_MDIO.

The HWREV can be checked by connecting to the fritzbox right after power
on via ftp:

  ftp> quote GETENV HWSubRevision

Within the same HW revision 5 of the Fritz!Box 3370 different NAND flash
chips are used. Usually it isn't a big deal but depending on the used
NAND flash chip, the ECC calculation is done different (and incompatible
of course).

Boards with a Micron MT29F1G08ABADA NAND flash chip are using the NAND
chip to calculate the ECC (on-die). Boards with a Hynix HY27UF081G2M NAND
flash chip are doing the ECC calculation in software.

Supporting both with a single DTS isn't possible. It might be possible
to add a patch selecting the ECC mode dynamicaly based on the found NAND
flash chip. But such a patch has no chance to get accepted upstream and
most likely need to be touched with every kernel update.

Instead two images are created. One for Micron NAND flash chip and one
for Hynix NAND flash chip. So far no pattern is known to identify the
used flash chip without opening the box.

Add the power off GPIO. At least EVA version 2186 sets/keeps the GPIO as
input, which will cause a reboot 30sec after power on. For boards with
EVA version 2186 the installation is tricky as it has to be finished
within the 30sec time frame.

The EVA version can be checked by connecting to the fritzbox right after
power on via ftp:

  ftp> quote GETENV urlader-version

The ath9k eeprom/caldata is at a different and offset and stored in
reverse order (from the last byte to the beginning) on the flash.
Reverse the bits to bring the data into the format expected by the
ath9k driver.

Since the ath9k eeprom is stored in reverse order on flash, we can not
use the mac address from the on flash eeprom. Get the MAC address from
the tffs instead.

Within the same HW revision 5 of the Fritz!Box 3370 both version of the
vr9 SoC are used. During preparation of kernel 4.14 support, all
devicetree source files were changed to load the vr9 v1.1 and vr9 v1.2
gphy firmware, which fixed the embedded phys for boards using the
version 1.2 of the vr9 SoC.

While at it, add a trigger to make use of the LAN LED. Setup the
build-in switch and add a hint for LuCI two show the ports in order
matching the labels on the case

Add support for the second USB port and provide the volatage GPIOs. Use
GPIO#21 as PCIe reset pin. The lan led is connected to GPIO#38.

Name the rootfs partition ubi and remove the mtd/rootfs related kernel
bootargs to use the OpenWrt autoprobing based on the partition name.

Enable sysupgrade support to allow an upgrade from a running system.
Since sysupgrade wasn't supported till now, drop image build code which
was added to allow a sysupgrade from earlier OpenWrt versions.

Build images that allow an (initial) installation via EVA bootloader.

To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote SETENV linux_fs_start 0
  ftp> quote MEDIA FLSH
  ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-kernel.bin mtd1
  ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-filesystem.bin mtd0

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
d7b7483343 lantiq: switch to kernel 4.14
Use kernel 4.14 by default.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
John Crispin
7e15e21766 Revert "ramips: mmc: Sync with staging drivers"
This reverts commit 2d401925b9.

Signed-off-by: John Crispin <john@phrozen.org>
2018-05-15 12:42:40 +02:00
Wei Yongjun
87c254c87e staging: mt7621-eth: fix return value check in mt7621_gsw_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: f079b6406348 ("staging: mt7621-eth: add gigabit switch driver (GSW)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:46:08 +02:00
Wei Yongjun
edec251870 staging: mt7621-eth: fix return value check in mtk_connect_phy_node()
In case of error, the function of_phy_connect() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.

Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:45:53 +02:00
Wei Yongjun
c4ae54dfab staging: mt7621-eth: fix return value check in mtk_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:45:34 +02:00
Rosen Penev
e07baec9fa ramips: pci: sync with staging driver
This is an amagalmation of two upstream commits dealing with whitespace
and dead code removal. I'm synching instead of having two separate commits
as they go out of order compared to previous commits here.

Tested on GnuBee PC1.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-15 06:45:07 +02:00
Rosen Penev
2d401925b9 ramips: mmc: Sync with staging drivers
Mostly whitespace cleanups. Some unneeded code was removed.

MMC init was also moved to the probe function as in
6069bdd087

The cleanup commits are over 100, making it hard to do them individually.

Tested on GnuBee PC1 with an SD card being used as swap.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-15 06:44:48 +02:00
Matthias Badaire
a0685deec4 ramips: Add i2c support for mt7620n
I2c is supported on mt7620n like on mt7620a when checking the datasheet

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-15 06:39:46 +02:00
Alberto Bursi
e09d4c850d kirkwood: support for buttons in Audi and Viper
Both these devices have a wps and a reset button on
GPIO pins, which need kmod-gpio-button-hotplug
package to work.

Add this package to their default package config.

Troubleshooted and tested on a Viper.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-05-15 06:39:37 +02:00
Johann Neuhauser
c15dfbeea0 ath79: fix gmac compatible in ar9330.dtsi and ag71xx_setup_gmac_933x
1. compatible property in node gmac was wrong

2. ag71xx_setup_gmac_933x should use np of gmac-config and
   not the pointer to gmac. gmac is only used for the reg address.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-05-15 06:38:07 +02:00
Michael Gray
bfbdeeb3de mvebu: add support for WRT32X (venom)
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.

Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-14 17:20:10 +02:00
Linus Walleij
1f56417e6b gemini: Augment DIR-685 device tree for RTL8366RB
This makes the ethernet and RTL8366RB come up on the
D-Link DIR-685.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-14 16:24:10 +02:00
Linus Walleij
3b48111df9 gemini: create zImage for DIR-685
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-14 16:24:09 +02:00
NeilBrown
edea934799 ramips: remove unnecessary resource details.
These resources are extracted from devicetree, so they aren't
needed here.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:24:07 +02:00
NeilBrown
1f78625714 ramips: remove conditional compilation.
Code currently defines:

and then compiles code only if they are defined.
We might want to disable some of these via devicetree one
day, but for now just remove the #defines and the
conditions - all the code for different ports is
easy to identify.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:24:04 +02:00
NeilBrown
5f7396ebef ramips: improve interrupt mapping
As the Interrupts for the PCI adapters are listed in
devicetree we shouldn't need to have them explicit in the code.

The simplest way to do this is to use of_irq_parse_and_map_pci()
and specify an interrupt-map which identifies the different
PCI hosts by bus/slot numbers.
This has the advantage that the hwirq number are mapped to virq
numbers for us, so the ugly hack can go.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:23:59 +02:00
Christian Lütke-Stetzkamp
2ad4daf579 ramips: Remove redundant owner assignment
Remove the owner assignment form the platform driver as
platform_driver_register() already initializes the owner.
Found using coccinelle.

Signed-off-by: Christian Lütke-Stetzkamp <christian@lkamp.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:23:36 +02:00
Rosen Penev
a098a78a33 ramips: Move PCI driver to files directory
This will make it easier to port upstream code.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-14 15:55:17 +02:00
Jo-Philipp Wich
aadca035bc at91: sama5d4: fix bad mkubifs options
Drop the "-x lzo" compression type override from MKUBIFS_OPTS since we
do not support it in mkfs.ubifs. Attempting to use LZO compression results
in "Error: bad compressor name".

The build system also appends an explicit "--compr=zlib" to the mkfs command
line, turning the "-x" flag into a no-op anyway.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-13 18:33:47 +02:00
Rafał Miłecki
404508001e kernel: use accepted version of bcm47xxpart fix commit
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 23:53:44 +02:00
Rafał Miłecki
070693477a kernel: backport mtd patch for minor partitioning cleanup
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 23:14:07 +02:00
Felix Fietkau
a3096b4b33 kernel: fix build error in flow offload code with CONFIG_NETFILTER=n
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-12 22:28:00 +02:00
Rafał Miłecki
02225f5763 bcm53xx: backport the first bunch of 4.18 BCM5301X patches
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 15:38:55 +02:00
Jo-Philipp Wich
cf7a88cf5a at91: cleanup kernel configurations
The subtarget configurations contained a lot of reduntant symbols, arbitrary
overrides and symbols set to =m.

Remove most of these redundant settings to shrink the subtarget configurations
to a manageable size.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 18:24:00 +02:00
Jo-Philipp Wich
f23326eb76 at91: sama5d2: remove CONFIG_XZ_DEC override
Fixes the following error spotted by the buildbot:

    Package kmod-fs-squashfs is missing dependencies for the following libraries:
    xz_dec.ko

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 16:40:34 +02:00
Jo-Philipp Wich
0167f53b9d at91: add missing config symbols
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 16:01:26 +02:00
Jo-Philipp Wich
d8c7cd9cb1 kernel: rtl8366_smi: guard of_mdiobus_register() call
Make the call to of_mdiobus_register() dependant on CONFIG_OF to avoid
pulling in an unwanted dependency on of_mdio.ko.

Fixes: 3dc523f232 kernel: add OF support to rtl8355 driver
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 15:07:56 +02:00
Piotr Dymacz
ce4d2fb5cc ar71xx: fix and improve ALFA Network Tube2H support
Fix ART offset (make it universal for 8/16 MB versions of the board) and
while at it, include also GPIO setup for h/w watchdog (EM6324QYSP5B).

Fixes: FS#1532

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-05-09 20:32:47 +02:00
Matthias Schiffer
db34cdf6c5
ath79: Ubiquiti Airmax M: add relocate-kernel to invalidate cache
Apply ar71xx fix for broken Ubiquiti bootloader to ath79 as well.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-05-08 21:14:24 +02:00
Felix Fietkau
6069bdd087 ramips: move mtk-mmc init to probe function to avoid breaking NAND flash
The driver messes with the pin control settings - MMC and NAND are
mutually exclusive

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-08 17:56:04 +02:00
Felix Fietkau
f95a4aa565 ramips: clean up the mt7621 nand flash driver hacks, add support for the xiaomi mir3g flash chip
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-08 17:56:04 +02:00
Rafał Miłecki
97f3c0f041 brcm47xx: switch to the kernel 4.14
The biggest (and the only?) disadventage of this is obviously an
increased image size.

For mips74k the size of vmlinux goes up from 4186684 B to 4701436 B.
Most devices use LZMA compressed kernel so probably more important is
vmlinux.lzma size which goes up from 1342945 B to the 1508498 B.

Still this isn't something that should stop target kernel bump. There
are various adventages of kernel 4.14. If kernel / image size is a
serious concern for anyone, it's perfectly possible to use previous
release which is pretty solid for the brcm47xx.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Paul Wassi <p.wassi@gmx.at>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
2018-05-08 09:55:10 +02:00
Rafał Miłecki
f9dcdc7fef kernel: mark source kernel for netfilter backports
This helps keeping track on patches & adding new kernels in the future.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-08 09:42:07 +02:00
Davide Ammirata
004cc22e4e ramips: add support for mqmaker witi 512mb version
Splitted out the dts file and create the new dts for the 256 MByte RAM and
the 512 MB RAM version.

Migrate both versions to the common board detection.

The install the 512 MByte Version on a board running the 256 MByte image,
a forceful sysupgrade with the -F flag is required.

Signed-off-by: Davide Ammirata <list@davidea.it>
2018-05-07 18:54:23 +02:00
Matthias Badaire
5ef79af4f8 ramips: add support for Ravpower WD03
The RavPower WD03 is a battery powered SD card reader and a USB port.

Specifications:
SOC:     MediaTek MT7620N
BATTERY: 6000mah
WLAN:    802.11bgn
LAN:     1x 10/100 Mbps Ethernet
USB:     1x USB 2.0 (Type-A)
RAM:     PM Tech PMD708416CTR-5CN 32 MB
FLASH:   Holtek HT66F40 - 8 MB Flash
LED:     Power button and 4 leds to indicate power level of the
         battery (could not get control of that)
INPUT:   Power, reset button
OTHER:   USB SD-Card reader with card detect on GPIO#42

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - installation from tftp
 - OpenWRT sysupgrade (Preserving and non-preserving)
 - LEDs
 - Buttons

Installation:
 - Download the sysupgrade image
 - Place it in the root of a clean TFTP server running on your computer.
 - Rename the image to "kernel" — be sure there is no file extension.
 - Plug the WD03 into your computer via ethernet.
 - Set your computer to use 10.10.10.254 as its IP address.
 - With your WD03 shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The WD03 (10.10.10.128) will look for your computer at 10.10.10.254
   and install the kernel file. Once it has finished installation of the
   kernel file, it will search for a (nonexistent) rootfs file — when it
   begins searching for this file, shut down the WD03 by holding the
   power button normally.
 - Start up your WD03 normally.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-07 18:54:23 +02:00
Mathias Kresin
ef19747b6c lantiq: kernel 4.14: Remove reboot/remove reset asserts
Backport patch accepted upstream which removes the reset asserts of the
xrx200 gphy driver on reboot/remove.

While doing a global software reset, these bits are not cleared and let
some bootloader fail to initialise the GPHYs. The bootloader don't expect
these bits to be set, as they aren't during power on.

The asserts were a workaround for a wrong syscon-reboot mask. With a mask
set which includes the GPHY resets of the first reset register, the
resets of the second reset register arn't required any more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 18:53:08 +02:00
John Crispin
99f10b193e ath79: drop dts/Makefile
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 15:01:12 +02:00
Russell Senior
4aacd6388a ath79: u-boot partitions should be read-only in dts
Some of the new ath79 device trees were missing read-only tags on the
u-boot partitions.  This adds the tags where previously missing.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-05-07 13:07:00 +02:00
Rafał Miłecki
4edd4cb2b3 ath79: use the new DT fixed partitions syntax
This new syntax is slightly better designed & uses "compatible" string.
For details see Documentation/devicetree/bindings/mtd/partition.txt .

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-07 12:57:47 +02:00
John Crispin
7fe77a5962 ath79: revert license change on upstream DTS files
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 12:52:03 +02:00
David Bauer
b6a4c67468 ar71xx: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.

SoC:   Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM:   Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi:  QCA9561 b/g/n 3x3 450Mbit/s
USB:   1x USB 2.0
IN:    WPS button, WiFi button
OUT:   Power LED green, Internet LED green, WLAN LED green,
       LAN LED green, INFO LED green, INFO LED red
UART:  Header Next to Black metal shield
       Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
       The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (LAN + WAN)
 - WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Not working:
 - USB port

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-07 10:42:26 +02:00
Rafał Miłecki
66c8afd115 ath79: relicense DTS files to the GPL 2.0+ / MIT
Some maintainers prefer DTS files licensed under permissive license like
MIT / BSD. As all DT bindings should be OS independent and DTS files are
pretty separated from Linux code it probably makes sense to share them
across projects.

The safest solution is to use dual licensing: that way it stays clear
these files can be used in GPL projects without depending on current
belief of licenses compatibility.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: John Crispin <john@phrozen.org>
2018-05-07 10:31:35 +02:00
John Crispin
53c474abbd ath79: add new OF only target for QCA MIPS silicon
This target aims to replace ar71xx mid-term. The big part that is still
missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik
subtargets will follow.

Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 08:06:51 +02:00
John Crispin
3dc523f232 kernel: add OF support to rtl8355 driver
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 08:06:51 +02:00
Rafał Miłecki
ed00387dc5 bcm53xx: switch to the new/alternative SPI controller driver
This switches bcm53xx from spi-bcm53xx to the spi-bcm-qspi driver. The
later one was developed by Broadcom and is more advanced one. It
supports more modes, setting a speed, setting bits per word and uses
IRQs instead of polling.

This increases kernel size from 1808120 B to the 1811160 B (by 3040 B).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-07 07:56:38 +02:00
John Crispin
6e0ae87a98 ramips: disable spi full duplex on mt7621
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-05 08:25:18 +02:00
Linus Walleij
6cd2e1f947 gemini: Add ethernet to DNS-313 and Wiliboard
This adds an interrim patch for v4.14 based on an
upstream commit to get ethernet working on D-Link DNS-313
(probably also on the Wiliboards)

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
ce93b05bf1 gemini: fix hard disk boot on D-Link devices
Since the D-Link devices boot from hard disk we need to
add the following changes to Gemini:

- Supply a bootarg in the device tree so we can boot from
  the right partition (/dev/sda4 on DNS-313)
- Disable forced command line in config so the kernel picks
  up the right bootargs from the device tree
- Enable EXT4 in the config as this is used for rootfs else
  we get nowhere, we cannot load this as a module because,
  well, it is supposed to be loaded from the root partition
  (chicken and egg problem).
- Enable jbd2 and mbcache (needed by ext4)

Also clean out the premature attempts to dynamically
modify the command line in the Image makefile: we should
pass this with the device tree bootargs instead, it works
much better.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
2c35bcffd0 gemini: add rtl8366rb to dir-685 board
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
af069fbd24 gemini: cleanup kernel config
Disable video and input drivers - they are needed only for one
board and can be enabled via modules if/when UI will be available.
Use LED drivers from packages.
Cleanup other things unnecessarily overriding defaults.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
91930c0f99 gemini: remove 4.4 support
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
6409b159e8 gemini: switch to 4.14
This introduces Device/ infrastructure and images
for all boards available upstream.

Changes from Linus submitted version:
- fix Raidsonic image generation
- remove redundant (old) image generation
- remove redundant header tool for dns313 board

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
4f74957584 gemini: add 4.14 support
This adds the patches to get fairly complete Gemini support
using kernel v4.14. It is mainly a backport of patches from
kernel v4.16 with omissions of things like graphics that require
substantial changes and will be better handled once we move
to the v4.16 kernel proper.
On top of this are some WIP patches for USB support.

Tested on Raidsonic NAS4220B and D-link DNS-313.

ChangeLog v4->v5:
- Fix ethernet single gmac usecase
- Fix USB reset (patch from Hans)
- Fix Raidsonic ethernet skew delay
- Fix kernel config (bridge, squashfs, jffs2, usb)
- Disable second usb port on Raidsonic board until fotg210_hcd is fixed

ChangeLog v3->v4:
- Make sure to use tabs rather than spaces in base-files.
- Use the dns313 image tool from the firmware-utils.
- Break out the addition of the v4.14 patches and the removal
  of the v4.4 patches to separate (big) patches.

ChangeLog v2->v3:
- Update the kernel config as indicated by Hauke Martens:
- Regenerate again after rebasing using kernel_oldconfig
  dropping a few optimization settings that are now generic
- Drop CFG80211 stuff (module)
- Drop CIFS stuff (module)
- Drop MAC80211 (module)
- Drop wireless drivers (module)
- Enabled OverlayFS
- Added proper DNS-313 boot image generation with the special
  file header tool.
- Disable CMA in the kernel
- Enable LZMA compression of the kernel
- Consequently name the nas4220b images nas4220b
- Update preinit MAC detection script to handle also DNS-313
- Add board.d/03_hdparm to set the disk to spin down after
  1 minute by default, if we have the hdparm tool installed

ChangeLog v1->v2:
- Processed config through kernel_oldconfig
- Processed patches through make target/linux/{clean,refresh} V=99

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
55c9aa27be gemini: rename files directory (preparation for 4.14)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Sandeep Sheriker Mallikarjun
610770dc5b at91: refreshing kernel configurations.
refreshing kernel configurations for sama5 and legacy subtarget.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
27ca6cdc7b at91: Add SAMA5D2 PTC EK board
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
60750ab505 at91: reorganize at91 subtargets
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
  1. able to set neon flags to sama5d2 & sama5d4 subtargets.
  2. fix the make clean which removes all the subtargets in bin folder.
  3. able to configure kernel specific to subtarget.
  4. able to set vfpu4 flags to samad3 subtargets.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
581f5e2392 at91: sdcard image with ext4 rootfs
creating sdcard image with ext4 rootfs only and ignoring creating
other filesystem in sdcard image.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:21 +02:00
Sandeep Sheriker Mallikarjun
22c398d257 at91: Add SAMA5D27 SOM1 EK board
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:21 +02:00
Sandeep Sheriker Mallikarjun
130224cc47 at91: fix sdcard create image
copying at91bootstrap and uboot binaries to sdcard image is done
based on device name instead of dts name and this avoids creating
multiple u-boot and at91bootstrap binaries.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:01 +02:00
Felix Fietkau
58f7b5b96c kernel: add missing in6_dev_put_clear call to an ipv6 network patch
Fixes "unregister_netdevice: waiting for lo to become free. Usage count = 1" messages

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-02 15:32:07 +02:00
Rosen Penev
45219c1c0f kernel: Restrict dmesg output to root.
In typical OpenWrt setups, there are no other users that have a shell spawned for them by default.

This can be overriden by the kernel.dmesg_output syssctl.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-04-30 09:01:33 +02:00
Sandeep Sheriker Mallikarjun
2391d6a29e at91: sama5: remove neon and VFPv4 support
sama5d2 & samad4 have neon feature and sama5d3 does not have neon
feature due to which sama5d3 boot fails with error message Kernel
panic - not syncing: Attempted to kill init! exitcode=0x00000004.
removing neon & VFPv4 support to fix this

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-04-30 09:01:12 +02:00
Sandeep Sheriker Mallikarjun
80fe9bd71c at91: fix build error for wb50n.
when external kernel is selected from menuconfig, device wb50n is not
avaliable and build fails. As a fix adding checks for external kernel.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-04-30 09:01:12 +02:00
Simon Paterson
264feab1e7 ar71xx: Add userspace support for Mikrotik rb-2011iLS
Kernel support already present.
Patch adds userspace for the 'iLS' suffix model of the RB2011 family.
Enables correct initial switch settings, sysupgrade, etc.

https://mikrotik.com/product/RB2011iLS-IN

Signed-off-by: Simon Paterson <simon.paterson.nz@gmail.com>
2018-04-30 09:01:12 +02:00
Koen Vandeputte
3435dbdc1c kernel: bump 4.14 to 4.14.37
Refreshed all patches

Compile-tested on: cns3xxx, imx6, octeon, ramips/mt7621, x86/64
Runtime-tested on: cns3xxx, imx6, octeon, ramips/mt7621, x86/64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[add extra tested targets to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-04-30 09:07:53 +03:00
Mathias Kresin
3877550114 arm64: enable harden branch predictor
Enable the harden branch predictor for arm64 as it is recommend.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-27 21:34:18 +02:00
Mathias Kresin
25f47c7bf9 kernel: add missing config symbols
The harden branch predictor was backported for arm64 with 4.9.92-96.

Fixes: 9aa196e0f2 ("kernel: bump 4.9 to bump 4.9.96")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-27 21:34:00 +02:00
Felix Fietkau
67aec988c4 brcm47xx: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-27 15:19:19 +02:00
Felix Fietkau
771f1ca3ff brcm63xx: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-27 15:19:19 +02:00
Felix Fietkau
1de74df8b9 bcm53xx: drop linux 4.4 and 4.9 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-27 15:19:19 +02:00
Christo Nedev
50b0919628 brcm2708: Add support for raspberry pi 3 b+.
Signed-off-by: Christo Nedev <christo.nedev@me.com>
2018-04-27 09:59:33 +02:00
Rosen Penev
7912677086 kernel: Fix data corruption on some mips devices.
This is mainly a bug fix for multi-core MIPS systems where L1 caches besides the primary do not get flushed.

The most obvious problem is data corruption on SATA and USB devices where read requests are typically larger than the cacheline size.

This may also fix ar71xx systems that suffer from similar data corruption but I have not tested if it does.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-04-27 09:59:33 +02:00
Matthias Schiffer
d168c2cf81
ar71xx: Ubiquiti Airmax M: add relocate-kernel to invalidate cache
Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956
(Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the
caches for the whole kernel address range after decompressing the kernel
image, leading to hard to debug boot failures, depending on kernel version
and configuration.

As a workaround, prepend the relocate-kernels loader, which will invalidate
the caches after moving the kernel to the correct load address.

Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-26 20:40:07 +02:00
Koen Vandeputte
6cd41b419c kernel: bump 4.14 to 4.14.36
Refreshed all patches.

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Fixes for CVEs:
CVE-2018-1108
CVE-2018-1092
CVE-2018-1094
CVE-2018-1095

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
2018-04-26 08:54:01 +02:00
Kevin Darbyshire-Bryant
9aa196e0f2 kernel: bump 4.9 to 4.9.96
Refresh patches, following required reworking:

ar71xx/patches-4.9/930-chipidea-pullup.patch
layerscape/patches-4.9/302-dts-support-layercape.patch
sunxi/patches-4.9/0052-stmmac-form-4-12.patch

Fixes for CVEs:
CVE-2018-1108
CVE-2018-1092

Tested on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Arjen de Korte <build+openwrt@de-korte.org>
2018-04-26 08:53:54 +02:00
Damir Samardzic
6f4faf833d mvebu: cortexa72: enable Marvell 10G PHY by default
This one enables 10 GbE ports on MACCHIATObin.

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
2018-04-25 20:37:22 +02:00
Mathias Kresin
91e11bec74 ramips: fix mt7628 eval board pinmux
There is no pinmux group "jtag" for mt7628 and the pinmux driver fails
to load due to the use of the not existing group.

Fixes: FS#1515

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-25 20:33:27 +02:00
Mathias Kresin
d089a5d773 ramips: create image for mt7628 evb board
The image for the EVB board got lost with the merge of the mt7628 and
mt7688 subtargets.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-23 22:07:22 +02:00
Tobias Wolf
3d800f14a9 ramips: use patch-dtb for F5D8235 V1
The old DTB method (OWRTDTB) is not recognized by the boot process
anymore with 4.9/4.14.

This patch reuses KERNEL_DTB to get a valid DTB applied to the kernel
image.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2018-04-23 22:07:22 +02:00
Giuseppe Lippolis
78666c7ba0 kernel: fix usb interface on 3G dwm-158 modem
The current option driver binds to the usb interface 2,3,4,5.
But the interface 4 and 5 doesn't answer to the AT commands.
On the new openwrt configuration the wwan script select the 5th
interface as control interface, failing to establish the
3G connection.

Backport the fix for the problem.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2018-04-23 22:07:22 +02:00
Sven Eckelmann
0b20490207 ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + 802.3at POE+
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 18-24V passive POE (mode B)
* powered only via POE

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

The initramfs image can be started using

  setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
  tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
  set fdt_high 0x85000000
  bootm 0x84000000

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00
Sven Eckelmann
c6aac196b8 ipq40xx: fix gpio-hog related boot issues
The pinctrl initialization fails with the MSM pinctrl code and gpio-hogs
because either the gpio ranges are not yet initialized (missing gpio-range
in DT) or that the msm driver unconditionally tries to re-initializes the
ranges (gpio-range in DT).

To allow gpio-hogs and similar early-boot gpio code, the gpio-ranges must
be in the device tree and the pinctrl-msm code must check whether the range
was already initialized by the DT.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[drop changes to unrelated dtsi files, refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-23 22:07:22 +02:00
Sven Eckelmann
856f0d5d0d ipq40xx: use upstream board-2.bin
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00
Rafał Miłecki
b1f5dd34ed brcm47xx: backport upstream patches for Netgear WNR1000 V3
This includes fix for reading NVRAM content.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-04-23 13:33:09 +02:00
Thomas Hebb
16b25ad829 ipq40xx: ex61x0v2: Disable unused GMACs
These devices have only one ethernet port. It doesn't make sense to
expose the unused GMACs as separate network devices.

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
2018-04-20 20:58:52 +02:00
Sven Eckelmann
c4c2a8f00c ipq40xx: Move reserved-memory DT to qcom-ipq4019.dtsi
The tz and smem reserved-memory information handled in the upstream Linux
sources by the SoC specific dtsi and not by the the boards dts. Using the
same approach in OpenWrt avoids unneccessary duplication.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-20 20:58:52 +02:00
Sven Eckelmann
0d62432834 ipq40xx: Remove unused reserved-memory nodes
The reserved-memory regions are mostly undocumented by QCA and are named
very unspecific in the QSDK device trees. It was tried to clean them up by
commit 71ed9f10a3 ("ipq40xx: Use detailed reserved memory for A42") and
similar changes.

The features which require these regions were mostly unknown but
Senthilkumar N L <snlakshm@qti.qualcomm.com> and Sricharan Ramabadhran
<srichara@qti.qualcomm.com> provided some more insight in some of them:

* crash dump feature
  - a couple of regions used when 'qca,scm_restart_reason' dt node has the
    value 'dload_status' not set to 1
    + apps_bl <0x87000000 0x400000>
    + sbl <0x87400000 0x100000>
    + cnss_debug <0x87400000 0x100000>
    + cpu_context_dump <0x87b00000 0x080000>
  - required driver not available in Linux
  - safe to remove
* QSEE app execution
  - region tz_apps <0x87b80000 0x280000>
  - required driver not available in Linux
  - safe to remove
* communication with TZ/QSEE
  - region smem <0x87b80000 0x280000>
  - driver changes not yet upstreamed
  - must not be removed because any access can crash kernel/program
* trustzone (QSEE) private memory
  - region tz <0x87e80000 0x180000>
  - must not be removed because any access can crash kernel/program

Removing the unnecessary regions saves some kilobyte of reserved-memory and
cleans up the device tree:

* 2560 KiB
  - 8devices Jalapeno
  - AVM FRITZ!Box 4040
  - Compex WPJ428
  - Meraki MR33 Access Point
  - OpenMesh A42
* 14336 KiB
  - GL.iNet GL-B1300
  - Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-20 20:58:52 +02:00
Mathias Kresin
74a0d8cd92 build: consolidate fake uImage header build commands
Merge the two existing functions and use a parameter for the type
header field.

It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-20 20:58:52 +02:00
Felix Fietkau
d89448fe43 mediatek: disable ubifs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-20 10:03:38 +02:00
Felix Fietkau
2fe0aaed7f mediatek: remove 4.9 kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-20 10:03:38 +02:00
Felix Fietkau
9ce5127a49 orion: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-19 14:38:57 +02:00
Felix Fietkau
decbecb0ad omap: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-19 14:38:53 +02:00
Felix Fietkau
57a7595a28 mvebu: drop linux 4.4 and 4.9 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-19 14:38:36 +02:00
Felix Fietkau
ca54bd1005 kernel: fix an issue with infinite stack traces on MIPS
Reproduced by enabling lockdep on MT7621

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-18 12:17:28 +02:00
Felix Fietkau
78d33056ab mediatek: enable ramdisk support by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-17 13:47:54 +02:00
Felix Fietkau
00dcccc74c mediatek: fix target FPU settings
This reverts commit 5555545494.
The target supports both NEON and VFPv4, but for this to work properly,
a few more changes are needed:
- enable NEON support in the kernel config
- add the fpu feature flag to the makefile

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-17 13:46:18 +02:00
Felix Fietkau
173d93ea23 ramips: fix locking issues in the ethernet driver
The stats update needs to protect against being interrupted by a tasklet
The u64 stats seqlock needs to be initialized

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-17 11:29:31 +02:00
Mathias Kresin
e988b0fe0d ramips: mt7620: fix double use of pins
The pins are used as (LED) GPIOs and can't be used at the same time as
hardware controlled ephy (LED) pins.

Fixes: FS#1500

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-17 08:40:56 +02:00
Stijn Tintel
ec1d7b9461 kernel: bump 4.14 to 4.14.34
Refresh patches.
Update patches that no longer apply:
- backport/313-netfilter-remove-defensive-check-on-malformed-packet.patch
- pending/642-net-8021q-support-hardware-flow-table-offload.patch

Compile-tested: x86/64.
Runtime-tested: x86/64.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-04-16 00:22:57 +03:00
Felix Fietkau
31a6ee0219 ramips: remove broken and bogus spinlock in the SPI driver
Based on patch by Neil Brown

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-14 20:12:32 +02:00
Felix Fietkau
ceff5d8c82 ramips: add missing unlock in fe_phy_link_adjust
Based on patch by Neil Brown

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-14 20:12:32 +02:00
Felix Fietkau
07b4e49abb ramips: fix usb phy compatible string (should fix FS#1489)
In the new USB phy driver, it checks the compatible string before
attempting to iomap its mem resource and do the extra PHY init

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-13 13:13:53 +02:00
Christian Lamparter
c61c709f4e apm821xx: Force Ethernet PHYID on MX60/MX60W
The MX60's uboot disables all the PHYs before starting linux.
This causes the PHY/switch detection code to malfunction
almost all of the time. To get around this, set a compatible
flag to force PHYID.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2018-04-13 07:51:43 +02:00
Mathias Kresin
fb528b1674 ipq40xx: unbundle firmware and board file
Don't select the firmware with the board file, it prevents an easy use
of the -ct ath10k firmware. Select the firmware within the default
packages instead.

Remove the per device selection of the firmware now that it the
firmware is selected by default.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-13 07:48:19 +02:00
David Bauer
970f1914be ipq40xx: add support for Netgear EX6100v2/EX6150v2
Specifications:
SOC:	Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:	256 MB Winbond W632GU6KB12J
FLASH:	16 MiB Macronix MX25L12805D
ETH:	Qualcomm QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11n/ac
	1x1 (EX6100)
	2x2 (EX6150)
INPUT:  Power, WPS, reset button
	AP / Range-extender toggle
LED:	Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL:	Header next to QCA8072 chip.
	VCC, TX, RX, GND (Square hole is VCC)
	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - 5 GHz WiFi (Correct MAC-address)
 - Factory installation from WebIF
 - Factory installation from tftp
 - OpenWRT sysupgrade (Preserving and non-preserving)
 - LEDs
 - Buttons

Not Working:
 - AP/Extender toggle-switch

Untested:
 - Support on EX6100v2. They share the same GPL-Code and vendor-images.
   The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
   board-blob. I only own a EX6150v2, therefore i am only able to verify
   functionality on this device.

Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.

Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.

Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.

See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-04-13 07:48:19 +02:00
Robert Marko
be6e28b516 ipq-wifi: Add 8devices Jalapeno
Add custom board-2.bin for 8devices Jalapeno.
Upstreaming is in progress.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-04-13 07:48:19 +02:00
Robert Marko
1e341bb5ef ipq40xx: add support for 8devices Jalapeno
This patch adds support for 8devices Jalapeno.

Specification:
QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz
256 MB of DDR3 RAM
8 MB of SPI NOR flash
128 MB of Winbond SPI NAND flash
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno
ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN)
phy@mdio3:
Label: eth0
gmac0
phy@mdio4:
Label: eth1
gmac1

Installation instructions:
Since boards ship with old version of LEDE installation is simple.
Just use sysupgrade -n -F sysupgrade.bin

Syuspgrade needs to be forced since OpenWRT uses DT detection in recent
releases.

If you get error that FIT configuration is not found during boot it is
due to older U-boot used on your board.
That is because 8devices used custom FIT configuration partition name
as they internally had v1 and v2 boards.
Only v2 boards are sold so now they are shipping boards with never
U-boot using generic config@1 FIT partition name.

Also for old uboot it is possible to force loading config@1 by changing
uboot environment:

setenv boot5 'bootm 0x84000000#config@1’
saveenv

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-04-13 07:48:19 +02:00
Rafał Miłecki
f5195e72c0 kernel: mtd: bcm47xxpart: improve handling TRX partition size
This is important fix for flash parsing in some corner cases. In case
of TRX subpartition with rootfs being aligned to the flash block size it
was incorrectly registered twice. Detecting & registering it as a
standalone partition was resulting in an incorrect "firmware" partition
size and possibly broken sysupgrade.

It wasn't noticed before because "rootfs" alignment depends on a kernel
size. It can happen though - depending on the configuration and the
kernel size.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-04-12 08:25:17 +02:00
Lucian Cristian
f93f29bccc
omap: kernel update and switch to 4.14
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-04-11 02:46:47 +02:00
Matthias Schiffer
e39847ea2f
ar71xx: increase kernel partition size for CPE/WBS 210/510
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-10 18:29:19 +02:00
Matthias Schiffer
5bfb344106
ar71xx: sysupgrade: improve CPE/WBS 210/510 validation, add new metadata offset
Previously, tplink_pharos_check_image() would accept any image with ELF
magic and only non-printable data in the support-list, as in this case the
while-read loop would not run at all. Add the new support-list offset and
ensure an image is only accepted when the model string is actually found.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-10 18:29:19 +02:00
Matthias Schiffer
d3f96fedec
ar71xx: increase kernel partition size for UniFi AP Pro and Outdoor+, enable devices again
Tested on UAP Outdoor+.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-10 15:27:39 +02:00
Matthias Schiffer
f8f6fa11c0
ar71xx: limit Ethernet speed of UBNT Airmax M (XM) devices to 100Mbit/s
Some Airmax devices can establish a Gigabit link even though the MAC only
supports 10/100 MBit/s, leading to broken connectivity. Prevent this from
happening by limiting the speed to 100MBit/s.

Fixes: FS#296
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-10 15:27:39 +02:00
Rafał Miłecki
31aaa670d4 ipq806x: replace linux,part-probe with a proper partitions subnode
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Acked-by: John Crispin <john@phrozen.org>
2018-04-09 07:45:34 +02:00
Rafał Miłecki
cdcd5c93d7 kernel: use accepted mtd patchset adding support for "compatible" string
These patches were finally accepted and are already present in the
Linus's tree. This should be good enough to make is "backport" material.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-04-09 07:16:48 +02:00
Mathias Kresin
dda5d9b786 ramips: rename pwm kernel module
With kernel 4.14 the OpenWrt specific module name collides with the
upstream added module for Mediatek ARM Socs.

During addition of preliminary support for kernel 4.14, the config
symbol used by the out of tree driver was already renamed but the ramips
kernel package wasn't updated.

Fix the build error by updating the config and kernel module name for
the kernel package.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-08 12:35:33 +02:00
Vianney le Clément de Saint-Marcq
bcf2125142 ramips: add support for Zorlik ZL5900V2
The Zorlik ZL5900V2 is an unbranded clone of HAME MPR-A1/2.  It is
marketed as "3G Wi-Fi Router".  Only the PCB has the model name
"ZL5900V2" printed on it.

Specifications:
- Ralink RT5350F (360 MHz)
- 32 MB RAM
- 8 MB Flash
- 802.11bgn 1T1R
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (Type-A)
- 5200 mAh battery

The ramdisk image (not the squashfs sysupgrade image) can be flashed
through the web interface (named "GoAhead") of the factory firmware.
However, as the factory firmware does not cleanly unmount the rootfs
before flashing, the device may hang instead of rebooting after
successful write.  Power cycling the device gets you in OpenWrt where
the squashfs image may be flashed through normal sysupgrade procedure.

Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
2018-04-08 09:53:50 +02:00
Zheng Qian
80a94aacaf ramips: add support for the YouHua WR1200JS
YouHua tech WR1200JS is an AC1200 router with 5 1Gb ports (4 Lan, 1 Wan)
and 1 USB 2.0 port.

Devices is base on MediaTek MT7621AT + MT7603E + MT7612E.

Specification:

- MT7612AT (880 MHz)
- 128 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 5x 10/100/1000 Mbps Ethernet
- 2T2R 2.4 GHz (MT7603E)
- 2T2R 5 GHz (MT7612E)
- 1x USB 2.0
- 10x LED (Power 2G 5G WPS Internet LAN4-1 USB)
- 3x button (reset wifi wps)
- DC jack for main power input (12V)

Installation:

1.) Press reset key 5 sec and restore the factory default
2.) Login webUI and change username to root and set a
    new password
3.) Visit http://192.168.2.254/adm/telnetd.shtml and
    turn on the telnet service
4.) Copy openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin
    to a usb pan
5.) Plug the usb pan to the router, telnet to the router
    and login by root
6.) cd /media/sda1 and check the initramfs file is there
7.) exec command:
    mtd_write write openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin Kernel
8.) reboot and visit 192.168.1.1

Signed-off-by: Zheng Qian <sotux82@gmail.com>
2018-04-08 09:52:48 +02:00
Giuseppe Lippolis
1680ae7eae ramips: add dwr-512 jboot firmware configuration
The previous fw version require the replacement of the stock bootloader
with u-boot. This prevent an easy stock restore of the original fw.

Now a proper fw util has been developed to manage the stock jboot
bootloader. Therefore make sense have a fw image for the stock
bootloader.

The old fw configuration (u-boot) is not compatible with the new one
and will not be supported anymore.

So at the end 2 image can be generated:

1) factory image with jboot bootloader
     openwrt-ramips-rt305x-dwr-512-b-squashfs-factory.bin
2) sysupgrade image with jboot bootloader
     openwrt-ramips-rt305x-dwr-512-b-squashfs-sysupgrade.bin

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2018-04-08 09:51:06 +02:00
Felix Fietkau
cb7ac151cd ar8216: reduce latency even further for ar8327 chips
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-08 09:27:14 +02:00
Felix Fietkau
17a955d4d7 ar8216: reduce latency by inserting scheduling points into code hogging the CPU
Should reduce network related latency caused by accessing MIB counters

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-08 09:14:23 +02:00
Vianney le Clément de Saint-Marcq
eda27d7557 ramips: fix usbphy DT nodes on linux 4.14
The Ralink USB PHY driver merged into mainline has a slightly different
device tree binding than the patch that was used with linux 4.9.
The new driver requires a `ralink,sysctl` node pointing to the `syscon`
node.

This patch also sets `#phy-cells` to 0, as recommended by the mainline
documentation [1].

[1] Documentation/devicetree/bindings/phy/ralink-usb-phy.txt

Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
2018-04-07 17:53:34 +02:00