In the drv_mac80211_setup function, mac80211_interface_cleanup
is called to ask the kernel to delete all existing interfaces
for the phy that is being configured via netlink.
Later in the first function, mac80211_prepare_vif is called to
set up the new interfaces as required.
But sometimes, when mac80211_prepare_vif (and so the relevant
`iw phy x interface add y` command) runs, the kernel might still
be cleaning up the old interface with the same ifname. It usually
takes very few time to do that; possibly a few milliseconds of
sleep in the script after detecting this error condition could be
enough, but the busybox sh does not support sub-second sleep
intervals.
When this happens, iw obviously fails to create the new interface;
and the following message is printed in the system log, followed by
subsequent failure messages from hostapd in case this would have been
an AP interface.
Tue Mar 14 04:21:57 2017 daemon.notice netifd: radio1 (2767): command failed: Too many open files in system (-23)
This was a long-standing issue existing since at least OpenWrt Backfire,
and today I finally managed to debug and (hopefully) solve it.
It was happening very few times on most devices; but it was happening
a lot more frequently on fast platforms with multiple radios, such as
the powerpc-based dual-ath9k-radio tl-wdr4900-v1.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
On the ath10k-devel ML Michael Kazior stated:
"board-2 is a key-value store of actual board files.
Some devices, notably qca61x4 hw3+ and qca4019 need
distinct board files to be uploaded. Otherwise they
fail in various ways." [0].
Later on Rajkumar Manoharan explained:
"In QCA4019 platform, only radio specific calibration
(pre-cal-data) is stored in flash. Board specific contents
are read from board-2.bin. For each radio appropriate board
data should be loaded. To fetch correct board data from
board-2.bin bundle, pre-cal/radio specific caldata should
be loaded first to get proper board id.
|My understanding until now was that:
|
| * pre-cal data + board-2.bin info == actual calibration data
Correct." [1].
The standard board-2.bin from the ath10k-firmware-qca4019
barely works on the RT-AC58U. Especially 5GHz clients fail
to connect at all and if they do, they have very low
throughput even right next to the router.
Currently, the solution for this problem is to supply a
custom board-2.bin for every device.
To implement this feature, this method makes use of:
Rafał Miłecki's "base-files: add support for overlaying
rootfs content". This comes with a few limitations:
1. Since there can only be one board-2.bin at the right
location, there can only one board overwrite installed
at any time. (All packages CONFLICT with each other.
It's also not possible to "builtin" multiple package.)
2. updating ath10k-firmware-qca4019 will also replace
the board-2.bin. For this cases the user needs to
manually reinstall the wifi-board package once the
ath10k-firmware-qca4019 is updated.
To create the individual board-2.bin: Use the ath10k-bdencoder
utility from the qca-swiss-army-knife repository:
<https://github.com/qca/qca-swiss-army-knife>
The raw board.bin files have to be extracted from the
vendor's source GPL.tar archieves.
Signed-off-by: Alexis Green <agreen@cococorp.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
With this patch, the nand.sh script no longer overwrites
CI_KERNELPART and CI_UBIPART if they have been set before.
This allows platforms specify alternative values for these
variables.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch enables the ATH10K_AHB support for the QCA4019
devices on the AHB bus.
This patch also removes 936-ath10k_skip_otp_check.patch
because it breaks the AHB device identification.
"Patch is wrong. I find it frustrating OpenWRT/LEDE doesn't
try to work with upstream on ixing these things right."
[1] <https://www.mail-archive.com/ath10k@lists.infradead.org/msg05896.html>
It also limits ath10k memory hunger (This is a problem with 128MiB RAM)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This change protects the openvpn instances to be marked as "in a crash
loop" and thereby the connection retries will run infinitely.
When the remote site of an openvpn connection goes down for some time
(network failure etc.) the openvpn instance in an openwrt/lede device
should not stop retrying to establish the connection.
With the current limit of 5 retries, there is a user interaction
required, which isn't really what you want when the device should
simply do everything to keep the vpn connection up.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Add actual mirror and use main site as last resport
Source: http://www.tcpdump.org/mirrors.html
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Add mirror and use main site as last resort.
Source: http://www.tcpdump.org/mirrors.html
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update util-linux to 2.29.2
Remote 0001-fix-uClibc-ng-scanf-check.patch as it's been merged upstream.
Refresh patches
Change ncurses to ncursesw to fix compilation and avoid confusion
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Refresh mirror list, some doesn't offer OpenSSL and add main site as last resort.
Source: https://www.openssl.org/source/mirror.html
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
This includes following changes:
480d7bc Fix sending unicast questions on cache expire
a0403cd Keep source sockaddr for every cached DNS record
1478293 Fix code freeing cached non-A(AAA) records too early
9f1cc22 Fix replying to "QU" questions received on unicast interface
943bedb Fix reading port of incoming packets
c725494 Use MCAST_PORT define for port 5353
ce7e9e9 Use one define for DNS-Based Service Discovery service name
e1bacef Drop entries cached for interface we're going to delete
496aeba Fix comment typo in cache_gc_timer
f89986b Fix refreshing cached A(AAA) records that expire
Previous updates made umdns work as expected on startup but there were
still many bugs. They were mostly related to runtime - cache management
and requests + responses. E.g. umdns was never able to send question on
DNS record expire. It was also ignoring all incoming unicast questions.
Since these issues are quite serious it makes sense to backport this
update to the stable branch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
a032166 interface-ip: set prefix indicator flag when IPv6 prefix lifetime changes
b4f8984 system-linux: parse vti specific settings as nested json data object
7e3b89a system-linux: parse gre specific settings as nested json data object
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This is the standard way we handle this. Please note (it seems) I could
drop few symbols as they are hidden under (disabled) DRM_LEGACY now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
For targets with i2c not built-in this fixes following error:
Package kmod-drm is missing dependencies for the following libraries:
i2c-core.ko
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If noresolv is set, we should not generate a --resolv-file parameter.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [minor cleanup]
9f02db7 mt76x2: fall back to software crypto for IBSS/Mesh per-sta GTK
4a54ab3 mt7603: fall back to software crypto for IBSS/Mesh per-sta GTK
712b8e8 mac80211: claim RSN IBSS support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The short log of changes since the 2016-06-10 release is below.
Jouni Malinen (1):
wireless-regdb: Remove DFS requirement for India (IN)
Ryan Mounce (1):
wireless-regdb: Update rules for Australia (AU) and add 60GHz rules
Seth Forshee (2):
wireless-regdb: Update 5 GHz rules for Canada
wireless-regdb: update regulatory.bin based on preceding changes
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
uClibc doesn't implement strerror_l() and thus libnl starting from
3.2.29 couldn't be compiled with it any longer, see
6c2d111177
To work-around that problem we'll just do a check on strerror_l()
availability during configuration and if it's not there just fall back
to locale-less strerror().
Patch for libnl is alreadfy merged upstream, see
e15966ac7f
and once the next libnl release happens this one must be removed from
Lede/OpenWrt.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Daniel Engberg <daniel.engberg.lists@pyret.net>
ntpd from Busybox supports peer-less (standalone) mode when it's started
with option -l and without any peer provided with option -p. In this
mode ntpd uses local time as reference and acts as stratum 1 server.
This mode can be used in isolated networks, where Internet access and/or
other NTP server/s are not available, but the device has some other way
of getting correct time, like e.g. GPS (ugps supports setting local time
by default).
Support for this mode was incorrectly disabled/removed in:
1527f96ca6
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
musl provides a /lib/libc.so file which should be integrated into the libc
package when the external toolchain with musl is used.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
03e44dc mt76x2: remove unnecessary headroom check
cc70498 mt76x2: clarify queue selection field
b056a78 dma: fix endian issue in mt76_dma_get_buf
f020a60 mt7603: support loading the entire EEPROM from OTP
29b08d3 mt7603: fix endian issue in mt7603_mcu_set_timing
dce8aac mt7603: fix endian issue in mt7603_mac_fill_rx
f22273b mt7603: init WTBL entry before setting capabilities
da8e796 mt7603: check wtbl busy status and stop/start tx queues when clearing sta entry
e54add5 mt7603: move napi/tasklet enable/disable outside of the locked section
59ce2b4 mt7603: set tx vif own MAC index (needed for beacons)
93ce124 mt7603: enable beacons for other virtual interfaces
c91e660 mt7603: set secondary beacon time offsets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This includes 3 cleanups:
fd5a160 Don't cache hosts as services
80dd246 Refresh DNS records A and AAAA directly
6515101 Access cached records (instead of services) to read list of hosts
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes the following security problems:
* CVE-2017-2784: Freeing of memory allocated on stack when validating a public key with a secp224k1 curve
* SLOTH vulnerability
* Denial of Service through Certificate Revocation List
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel unconditionally pulls in a header file that defines
'current', which conflicts with the lua extension code.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce RT6352 instead of matching against RF7620.
Clean up channel setting rfvals.
Port bandwidth filter calibration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Overwrite an already set proto if a new one is passed to
_ucidef_set_interface() similar to what is done for the interface.
It is required when using ""ucidef_set_interface_wan 'ptm0' 'pppoe'"
after some initial wan interface configuration is already done by
ucidef_add_switch.
The "json_is_a protocol string" guard is meant to not reset an earlier
set interface proto in case something like
"ucidef_set_interface_lan 'eth0'" is used afterwards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes crash in interface_start caused by freeing interface in
interface_free without stopping a timeout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
So here is another round of improvements for MT7620 WiFi.
This commit fixes a few significant issues related to TX_PWR_CFG_x and
TX_ALC and also makes the code more readable by adding register
descriptions for things added for MT7620 and use the usual bit-field
access macros and the now defined macros instead of plain bit-ops and
magic numbers.
Properly describe EEPROM_TARGET_POWER at word 0x68 (== byte 0xD0) and
thereby fix internal TXALC which would otherwise just read
out-of-bounds of the EEPROM map.
Split-out tx-power/ALC related stuff into an additional function.
Fix VCO calibration, it was carried out properly in the channel
switching but incomplete in the actual VCO calibration function.
Also there is no need to trigger VCO calibration in channel switching,
the VCO calibration function is already being called at this point.
Remove it from channel switching function to avoid redundant code.
The TX power calibration differs significantly from all other
Mediatek/Ralink chips: They finally allow 0.5dB steps stored as 8-bit
values for (almost) each bitrate -- and promptly ran out of space and
for some reason didn't want to change the EEPROM layout. The hence
opted for a scheme of sharing values for some adjecent bitrates and
a highly over-complicated (or obfuscated?) way to populate the
TX_PWR_CFG_x registers with the values stored in the EEPROM.
The code here now looks much less complicated than what you see in the
vendor's driver, however, it does the exact same thing:
bGpwrdeltaMinus is a constant and always TRUE, hence half of the
code was dead. Gpwrdelta is always 0 (rather than using the value read
from the EEPROM). What remains is some very grotesque effort to avoid
0x20, probably some hardware bug related to some misunderstanding of
what a singed 8-bit value is (imagine: if it was a signed 6-bit value
then someone could believe that 0x20 == 0x0). And then they didn't
clean it up once they later on anandonned that whole story of having a
constant offset for 40 MHz channels and just set the offset to be
constant 0 -- there is no effort for avoiding 0x20 for the 20 MHz
values stored in the EEPROM, hence that's probably just a forbidden
value in the EEPROM specs and won't appear anyway...
Anyway, the whole thing felt like solving some college math test
where in the end everything cancels out and the result equals 0 ;)
To make sure that channel bandwidth power compensation really doesn't
need to be taken care of, output a warning when the corresponding
value stored in the EEPROM is non-zero.
Also there is no apparent reason to refrain from initializing RFCSR
register 13, it doesn't fail what-so-ever.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
RFC 6761 defines a number of top level domains should not be forwarded
to the Internet's domain servers since they are not responsible for
those domains.
This change adds a list of domains that will be blocked when 'boguspriv'
is used and augments that which is already blocked by dnsmasq's notion
of 'local service' using '--bogus-priv' i.e. RFC 1918 private addresses
and IPv6 prefixes as defined in RFC 6303.
To make this configurable rather than hard coded in dnsmasq's init
script, a new file /usr/share/dnsmasq/rfc6761.conf is conditionally
included.
The default file matches the RFC 6761 recommendation along with a few
other top level domains that should not be forwarded to the Internet.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
The ugps tool expects device path in last argument. If it's provided
before other options, they won't be processed at all.
Additionally, make it possible to use absolute path for gps character
device in related uci configuration.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
continue work started here: http://patchwork.ozlabs.org/patch/520859
Extend /etc/config/system with parameters to set the default respawn treshold and respawn timeout
for procd launched services that have respawn enabled.
This results in cleaner init scripts, while making sure services have respawn parameters set.
Signed-off-by: Claudiu Brasovean <cbrasho@gmail.com>
Open-code usb_phy_generic_register instead of calling it, since it is
really trivial. Avoid pulling CONFIG_NOP_USB_XCEIV into the kernel
config and add a proper dependency instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If ehci platform driver is loaded before the chipidea controller driver,
both are competing for the same IO resources and the generic driver gets
used for the hardware. This results in USB device mode being
unavailable.
Split generic EHCI support code out of kmod-usb2, so that the chipidea
driver can be included without also pulling in the generic one. Also
rework the load order, so that the chipidea driver gets loaded first, in
case both are installed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Honour the parent interfaces peerdns option when spawning a virtual DHCPv6
interface in order to avoid pulling in IPv6 DNS servers when the user opted
to inhibit peer DNS servers in the configuration.
Fixes#597.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
8f218f5 procd: service gets deleted when its last instance is freed
35209a0 procd: update modprobe path
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Update to latest Git in order to import the following fixes:
19070b6 unarchive: fix possible segmentation fault in deb_extract()
758527e pkg: forward "provided_by_hand" flag in pkg_merge()
1fdc2ca pkg: mark bit fields in pkg_t unsigned
15fc1ee opkg_cmd: avoid null pointer dereference in opkg_what_depends_conflicts_cmd()
439c89e opkg_cmd: fix endless loop in whatprovides/whatreplaces
0fb3e9f pkg_depends: propagate virtual provided detail flag to providers
793155f pkg_depends: fix unsatisfied dependency installation order
b1dc770 libopkg: fix some overly aggressive line wrapping in pkg_depends.c
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
We need to let external toolchains be able to specify the path and
specification file to the libthread-db POSIX thread debugging shared
libraries.
This fixes GDB not being able to be installed because it is depending on
libthread-db:
Collected errors:
* satisfy_dependencies_for: Cannot satisfy the following dependencies
* for gdb:
* libthread-db *
* opkg_install_cmd: Cannot install package gdb.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The current way of creating a STAMP_CONFIGURED filename for OpenSSL can
lead to an extremely long filename that makes touch unable to create it,
and fail the build.
Use mkhash to produce a hash against OPENSSL_OPTIONS which creates a
shortert stamp file,
Fixes#572
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Pass down TARGET_CPPFLAGS for path to header files, and append the
libraries we depend on in TARGET_LDFLAGS. Put TARGET_LDFLAGS at the end
of the command line as is required by modern GCC/binutils.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes build issues with external toolchains that do not have STAGING_DIR
in their default search path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes linking failures observed with external toolchains:
/home/florian/dev/toolchains/stbgcc-4.8-1.5/bin/../lib/gcc/mipsel-linux-gnu/4.8.5/../../../../mipsel-linux-gnu/bin/ld:
warning: libubox.so, needed by
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so,
not found (try using -rpath or -rpath-link)
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_open_nested'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_parse'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blob_nest_end'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_add_field'
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Make sure we pass down TARGET_CPPFLAGS to let toolchains with no default
search paths to find the mbdetls headers, and override TARGET_LDFLAGS to
include libraries we are linking against.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Brings the following changes:
22f041e18df0 Extend StandardEject sequence to include LUN 1
61fdf7e9b1cc cmake: Search for libjson-c
2769852e76b5 cmake: Find libubox/blobmsg_json.h
8a47c4b6649f add TargetClass support
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
thc-ipv6 did not allow an external environment to override CFLAGS, which
would lead to our CFLAGS not being passed properly (relro,
optimizations, etc...)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The following will enable the TPM kernel module, as well as support for
the atmel i2c TPM driver. Tested and confirmed working on an Aerohive
AP-121
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Backport kernel patches for LS1043A Rev1.1 support from upstream,
patchwork, and SDK. And update to latest u-boot to support LS1043A
Rev1.1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Drops a LEDE carried patch now upstream.
Convert to autotools.
A number of nits fixed upstream (dns & short packet handling most
notable)
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
c09e4f0 ubusd: fix incomplete copy of shared buf during queue-ing
453b87f cli: add support for subscribing to objects
6eb3c96 cli: do not use default timeout for listen
dfe3383 libubus: reset ctx->sock.error when doing ubus reconnect
34c6e81 cli: fix listen_timeout compile issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is required for default wireless configuration of malta target to
work out of the box again. Fixes "77ece30e: hostapd: Add ability to
specify that that wireless driver supports 802.11ac"
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
When not defining 'device' or 'vlan' in relevant switch_port uci
sections, behaviour is inconsistent due to *devn, *port and *vlan
pointers not being zero initialized.
Signed-off-by: Ben Kelly <ben@benjii.net>
This is needed for the definition of $(LINUX_DIR). This is used in
u-boot.mk to change the device-tree compiler to the dtc used by
linux.
Without this, the build will use the system dtc. This results in a
build failure when a dtc does not exist outside the buildroot.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
stop() is overwritten by rc.common, so implement stop_service instead.
While at it, remove the now unnecessary restart() override
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch splits `kmod-mt76` into three separate packages:
`kmod-mt76-core`, `kmod-mt76x2` and `kmod-mt7603`. By making
`kmod-mt76` a metapackage containing these new packages,
the previous behaviour of including all drivers and firmware
is left unchanged, unless explicitly unselected in
`DEVICE_PACKAGES`.
This splitting is especially beneficial for devices with
small flash chips, since the `kmod-mt76` package currently
requires ~160K on squashfs (after compression).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
Update to latest Git head to get rid of a stray printf() causing unwanted
output in the "opkg list-upgradable" command.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
--bogus-priv now applies to IPv6 prefixes as specified in RFC6303 - this
is significantly friendlier to upstream servers.
CNAME fix in auth mode - A domain can only have a CNAME if it has no
other records
Drop 2 patches now included upstream.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
A missing list pointer initialization caused opkg to ignore conffile entries
from status files, breaking the conffile tracking on the target.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
c553354 cmake: fix typo
8973576 kmodloader: fix not being able to find some modules
fce9382 cmake: Check for getrandom system call
Signed-off-by: Felix Fietkau <nbd@nbd.name>
px5g-standalone only supports SHA1 for certificates, which is strongly
deprecated. The new px5g-standalone is about 27k bigger (compressed),
and has identical behavior to px5g-mbedtls (it uses SHA256).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The switch to cmake caused the -DHAVE_USIGN flag to get lost, disabling
compilation of the correspondinf support code.
Update to latest Git head which enables usign support by default.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This reverts commit cc66f819b4.
This commit causes opkg to install px5g-standalone instead of px5g when
installing luci-ssl. As luci-ssl depends on mbedtls, using
px5g-standalone makes no sense. Next to that, it creates deprecated SHA1
certificates. Revert the commit to avoid pxg5-standalone to be
installed by accident.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
- Fix eap test to work with standalone hostapd builds
- Fix 11n test to check the correct define
- Add 11ac, 11r and 11w tests
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
New test release (since test1) includes 2 LEDE patches that are
upstream and may be dropped, along with many spelling fixes.
Add forthcoming 2017 root zone trust anchor to trust-anchors.conf.
Backport 2 patches that just missed test3:
Reduce logspam of those domains handled locally 'local addresses only'
Implement RFC-6842 (Client-ids in DHCP replies)
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Specifying USE_PRIVATE_LIBGCC is no longer needed, as it is the
default.
Patch 001 is removed, since it was already merged upstream. Patches
100 and 101 are removed because they do not appear to be needed
anymore, and they do not conform with the sign-off and commit message
procedures.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Because they were hidden, there was no way to disable the uboot
targets in menuconfig, so they had to be built every time. The omap
target is the only one to hide uboot packages. To be consistent with
the other targets, and have more control over the build, un-hide the
u-boot packages.
Note that the default behavior remains unchanged, as uboot will be
built unless explicitly disabled.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Switch to our own fork of opkg to significantly reduce the required amount
of memory when updating lists or installing packages.
Preliminary tests showed a usage drop of about 90% during these operations,
from ~3.7MB with unmodified opkg to ~360KB with our custom fork.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Removing redundant spaces from the name of the option. Without fix:
root@LEDE:~# opkg install ugps
Installing ugps (2016-10-24-32a6b2b7-1) to root...
Downloading http://downloads.lede-project.org/releases/17.01-SNAPSHOT/packages/mips_24kc/base/ugps_2016-10-24-32a6b2b7-1_mips_24kc.ipk
Configuring ugps.
uci: Parse error (invalid character in name field) at line 3, byte 23
uci: Parse error (invalid character in name field) at line 3, byte 23
sh: out of range
root@LEDE:~# uci show gps
uci: Parse error (invalid character in name field) at line 3, byte 23
With this fix:
root@LEDE:~# uci show gps
gps.@gps[0]=gps
gps.@gps[0].tty='ttyACM0'
gps.@gps[0].adjust_time='1'
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
This update includes numerous small fixes for:
1) Interfaces setup
2) Packets parsing
3) Sending replies
Without this there were multiple problems with exchanging information
between (u)mdns and other implementations (including (u)mdns as well).
This also follows project rename to umdns which was required to avoid
confusion with Apple's mdnsd from mDNSResponder project.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
5f91241 procd: add cancel_timeout on rc scripts when a runtime_timeout is specified
961dc69 procd: stop service using SIGKILL if SIGTERM failed to do so
Signed-off-by: John Crispin <john@phrozen.org>
Default trigger action timeout was added to procd.sh in commit f88e3a4c0
(procd: add default timeout for reload trigger actions)
However, the timeout value was not placed under the correct JSON-script
array nesting level and thus did not apply.
To fix this and make the timeout actually apply to the reload triggers,
we place it in the correct scope, that is the per-trigger array.
Fixes: f88e3a4c0a
Signed-off-by: Denis Osvald <denis.osvald@sartura.hr>
This can be used to tweak the buildbot behavior without having to change
buildbot's configuration.
It will also allow us to add more aggressive clean steps (e.g. on
toolchain changes), which would break developers' workflows if enable
by default.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
fixes issue "nsa 310b u-boot can initialize usb but cannot
use usb storage so it cannot load files from usb"
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
as we do for IPv4 PPP interfaces. When we create the
dynamic IPv6 interface we should inherit ip6table from
main interface.
Signed-off-by: Ulrich Weber <ulrich.weber@riverbed.com>
pppoe-discovery performs the same discovery process as pppoe, but does
not initiate a session
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
When running wifi detect, the user will be told on error output that
wifi detect is deprecated, that wifi config must be used instead. Also
the commit that changes it is referenced for further info.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
Since commit 5f8f8a3661 wifi detect does
not longer work and wifi config it's used to configure not yet
configured wireless devices.
This commit changes command usage to reflect that change.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
f107656 netifd: Add option to configure locktime for each device
cdc0e80 interface: add prefix assignment priority support
6397f5e device: add veth support
6228d0f wireless: fix _wireless_add_process
7cc2f10 treewide: fix white space errors
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Effects of the bugs could include memory corruption, tx hangs, kernel
crahes, possibly other things as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Important change was made in 1.0.18: all sub-libs were merged
in one and only libc similarly to musl.
See [1] for more details.
To support that we had to remove refences to those sub-libs like
libpthread, libcrypt, libdl, libm, libutil etc.
[1] http://cgit.uclibc-ng.org/cgi/cgit/uclibc-ng.git/commit/?id=29ff9055c80efe77a7130767a9fcb3ab8c67e8ce
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
The only HMACs currently available use MD5 and SHA1, both of which have known
weaknesses. We already compile in the SHA256 code since we use Curve25519
by default, so there's no significant size penalty to enabling this.
Signed-off-by: Joseph C. Sible <josephcsible@users.noreply.github.com>
Remove CONFIG_VLAN_8021Q overrides for two targets
These features are built into the kernel image for all targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When calling erase() on a containers derived from __base_associative
(e.g. multimap) and providing a pair of iterators a segfault will
occur.
Example code to reproduce:
typedef std::multimap<int, int> testmap;
testmap t;
t.insert(std::pair<int, int>(1, 1));
t.insert(std::pair<int, int>(2, 1));
t.insert(std::pair<int, int>(3, 1));
t.erase(t.begin(), t.end());
Signed-off-by: Ben Kelly <ben@benjii.net>
Goflexhome/net use uImage, and to boot an uImage the u-boot
must use bootm command, not bootz.
Fixes the "i cannot boot LEDE with this u-boot" issue that I
found out myself with my goflexnet.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
all patches for CONFIG_SYS_GENERIC_BOARD are obsolete for
uboot 2016 sources.
Run-tested with the uboot of goflexnet, also the md5sum of
all other uboots is the same with or without these patches.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* Update to 1.43.4
* Use xz tarball which saves about 2Mbyte in size
Changelog: http://e2fsprogs.sourceforge.net/e2fsprogs-release.html#1.43.4
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [use @KERNEL instead of hardcoded URL]
This commit combines all the changes I've made on my staging tree
into a single commit fixing many issues with our patch for MT7620.
First of all, checkpatch.pl revealed numerous code style issues with
the patch, so fix all the white-space and commets. Also use
usleep_range instead of legacy timing and relax timing for VCO
calibration just like the vendor driver does.
Several line programming registers were commented out in the patch.
Originally this came from the features present but disabled by default
in the vendor's driver (RTMP_TEMPERATURE_CALIBRATION and
ADJUST_POWER_CONSUMPTION_SUPPORT). Remove the dead code for now, it can
easily be re-added if we actually intend to support those features.
Move values from mt7620_freqconfig type into the existing rf_channel
struct, this shouldn't be a new typedef and it is possible to use the
existing struct because rf_channel got 4 32-bit fields, so two of the
8-bit values from mt7620_freqconfig can easily be stored in the same
32-bit field.
Map values such that
Rdiv -> rf1
N -> rf2
K -> rf3[0:7]
D -> rf3[8:15]
Ksd -> rf4
This makes the channel switching logic already look a bit more like
what we are used to in rt2x00... Probably many of the read-modify-write
calls could still be replaced by macros intended for that.
iq calibration seems to be identical to RT5592, so just enable it.
Test shows that this improves things quite a lot, datarates went up
by a couple of megabits when running iperf, signal quality seems jumpy
in the first few seconds once a station connencts, the stabelizes on a
value significantly better than what it was before.
Add description to the patch and reference the original OpenWrt commit
by which it was added.
The patch now passes checkpatch.pl and can thus be discussed with the
upstream authors of the rt2x00 driver.
Funded-by: https://www.kickstarter.com/projects/1327597961/better-support-for-mt7620a-n-in-openwrt-lede/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Bump to dnsmasq 2.77test1 - this includes a number of fixes since 2.76
and allows dropping of 2 LEDE carried patches.
Notable fix in rrfilter code when talking to Nominum's DNS servers
especially with DNSSEC.
A patch to switch dnsmasq back to 'soft fail' for SERVFAIL responses
from dns servers is also included. This mean dnsmasq tries all
configured servers before giving up.
A 'localise queries' enhancement has also been backported (it will
appear in test2/rc'n') this is especially important if using the
recently imported to LEDE 'use dnsmasq standalone' feature 9525743c
I have been following dnsmasq HEAD ever since 2.76 release.
Compile & Run tested: ar71xx, Archer C7 v2
Tested-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ref commit 9525743c07
dnsmasq: make DHCPv6 viable for standalone dnsmasq install
Above commit broke instancing by missing filter_dnsmasq()
as part of the dhcp_add() execution.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Do not spam the syslog with DHCPv6 lease info if quietdhcp option
is selected. This already works for DHCPv4, make it work in the same
way for DHCPv6.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
[Originally written by Arjen de Korte on GitHub but had issues providing
a SoB in correct format.]
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Adds the following fixes:
91acde6 libubus: do not modify uloop_cancelled
763b9b2 libubus: reset ctx->sock.eof to fix reconnect issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adds the following changes:
de3f14b uloop: add uloop_cancelling function
3b6181b utils: fix build on Mac OS X 10.12
7f671b1 blobmsg: add support for double
0fe1374 utils: add helper functions useful for allocating a ring buffer
8fc1c30 libubox: replace strtok with _r version.
4a9f74f libubox: allow reading out the pid of uloop process in lua
372e1e6 uloop: remove useless epoll data assignment
f9db1cb libubox: allow reading out the remaining time of a uloop timer in Lua
Signed-off-by: Felix Fietkau <nbd@nbd.name>
key_direction shows up as an openvpn option in the user-interface but does not end up in the /var/etc/openvpn*.conf file. Adding it to the list here fixed the issue for me.
Signed-off-by: Brandon Koepke <bdkoepke@fastmail.com>
Update ubox to latest Git HEAD in order to import the following fixes:
ac2d43e kmodloader: support '-q' quiet option
f8d3d16 ubox: Add an option for more accurate timestamps in log
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Lots of users try random stuff when they encounter any kind of
difficulty. I've had to debug a number of cases where people had enabled
this option for no reason. Hopefully this warning will reduce the number
of useless support cases.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
I needed a moment to figure out relation between this patchset and the
nl80211: fix validation of scheduled scan info for wowlan netdetect
It appears nl80211 commit will go on top of brcmfmac changes so it's
safe to backport these patches.
One patch that was excluded is commit 2a2a5d1835b6 ("brcmfmac: add
.update_connect_params() callback") as it depends on missing commit
088e8df82f91 ("cfg80211: Add support to update connection parameters").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
samba.org has started to enforce https and
currently plain http downloads with curl/wget fail,
so convert samba.org download links to use https.
Modernise links at the same time.
Also convert samba.org URL fields to have https.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
dnsmasq has sufficient services to meet the needs of DHCP
and RA with IP6 for single router router users. This is
the most common use for consumer routers. Its reenforced
as most ISP tend to only DHCP-PD /64. dnsmasq has year
over year demonstrated great flexibility in its option
set, and support for off-standard DHCP clients.
odhcpd has enhanced capabilities focused on IP6 such
as DHCP/RA relay and NDP proxy. However, it is not as
flexible in its option set. odhcpd is not as forgiving
with off-standard DHCP clients. Some points may represent
a long term TODO list, but it is the state currently.
These changes make any such combination possible. Already
odhcpd can be set as the main dhcp server. Now odhcpd
can be removed or disabled and dnsmasq will take over
if DHCPv6 compiled in. The existing DHCPv6 and RA UCI
are translated into dnsmasq.conf. The changes focus on
'--dhcp-range', '--dhcp-host', and '--dhcp-options'.
DHCP host ID is least 16 bits [::1000-::FFFF], but
leaves low range for typical infrastructure assignments.
dnsmasq accepts DHCPv6 options in the tranditional
'--dhcp-option' put they must be prefixed 'option6:'.
dnsmasq will also discover SLAAC DNS entries from DHCPv4
clients MAC, and confirm with a ping at least renew.
Long term TODO include improving use of dnsmasq relay
options for DHCPv4 and DHCPv6 in parallel. It would also
be possible to preconfigure DHCP-PD in host-with-options
records for fixed infrastructure.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
[Jo-Philipp Wich: emit proper IPv6 hostid format in dhcp-host directive]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
ref commit 612e2276b4
ref commit ec63e3bf13
'option add_local_hostname' scripted implementation statically assigns
this host in auto generated host file at init. If IFUP or other signals
do not occur, then address changes are not tracked. The script doesn't
apply all the addresses at an interface. This may make logs obscure.
The script only puts the bare host name (maybe not FQDN) in host file,
but if '--exapandhosts' is enabled, then /etc/hosts entries will be
suffixed, and "127.0.0.1 localhost" becomes "localhost.lan".
dnsmasq provides an option to perform this function, but it is rather
greedy. '--interface-name=<name>,<iface>' will assign the name to all
IP on the specified interface (except link local). This is a useful
feature, but some setups depend on the original restrictive behavior.
'option add_local_fqdn' is added to enhance the feature set, but
if not entered or empty string, then it will default to original
option and behavior. This new option has a few settings. At each
increased setting the most detailed name becomes the PTR record:
0 - same as add_local_hostname 0 or disabled
1 - same as add_local_hostname 1
2 - assigns the bare host name to all IP w/ --dnsmasq-interface
3 - assigns the FQDN and host to all IP w/ --dnsmasq-interface
4 - assigns <iface>.<host>.<domain> and above w/ --dnsmasq-nterface
'option add_wan_fqdn' is added to run the same procedure on
inferred WAN intefaces. If an interface has 'config dhcp' and
'option ignore 1' set, then it is considered WAN. The original
option would only run on DHCP serving interfaces.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Instead of only using tagged CPU port configurations when more than one VLAN
is present on the switch, always emit tagged configurations unless a board
explicitely opts out of this behaviour by using the previously introduced
[0-9]u@netdev syntax.
Emitting default tagged configurations has the following benefits:
- Relation of switch vlans to netdevs is easier to understand, especially
for multi-cpu-port switches
- Adding additional VLANs (e.g. to break out a LAN port for other purposes)
becomes easier as users are not forced to change the existing untagged
VLAN to tagged and the existing ifname notation from ethX to ethX.Y
anymore, drastly reducing the likelyhood of soft-bricks.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes firmware crash in rare cases and a bug
ath10k_pci 0001:01:00.0: received unexpected tx_fetch_ind event: in
push mode
for those who kept experiencing it after previous firmware update.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Uses upstream code to parse DT supported band/frequency information.
Update existing .dts files to the new format and remove unnecessary
overrides.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
And, update support for 9880 chipsets. The new firmware
fixes a regression with EAPOL 4/4 packets added in
a recent commit.
It also fixes a case where the firmware would improperly try
to use STBC when configured for 1x1 (as 9887 always is).
Signed-off-by: Ben Greear <greearb@candelatech.com>
The driver had a bug when calculating the rateset. This resolves
that and allows full VHT mcs rates on 2x2 hardware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Some debugging/error messages are printed using wpa_printf and this
change allows finally reading them out of the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This will allow starting hostapd with the new -s parameter and finally
read all (error) messages from the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
wash, mpu & some memory optimisation have now made it to the official
cake repository.
Point LEDE to the official repository.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
c13b6a0 dhcpv6: fix white space error
e9d80cc dhcpv6: trigger restart of DHCPv6 state machine when not
receiving statefull options
c7122ec update README
419fb63 dhcpv6: server unicast option support
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The condition is always true due to the literal string followed the
-n test parameter. A model name set by target scripts always gets
overwritten this way.
Change the condition to check for an already existing destination file
as it was before 5e85ae9 ("base-files: fix error message during boot").
Signed-off-by: Mathias Kresin <dev@kresin.me>
It wasn't possible to read hostapd wpa_printf messages unless running
hostapd manually. It was because hostapd was printing them using vprintf
and not directly to the syslog.
We were trying to workaround this problem by redirecting STDIN_FILENO
and STDOUT_FILENO but it was working only for the initialization phase.
As soon as hostapd did os_daemonize our solution stopped working.
Please note despite the subject this change doesn't affect debug level
messages only but just everything printed by hostapd with wpa_printf
including MSG_ERROR-s. This makes it even more important as reading
error messages can be quite useful for debugging.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes build issues with some toolchains that don't add lcrypt in the default
search paths:
CMakeFiles/rpcd.dir/session.c.o: In function `rpc_login_test_password':
build_dir/target-mipsel-linux-gnu/rpcd-2016-12-03-0577cfc1/session.c:823: undefined reference to `crypt'
collect2: error: ld returned 1 exit status
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Some toolchains will produce executables with an interpreter that is e.g:
ld.so.1 (typically a symbolic link). Due to our current LIBC_SPEC_FILE value,
we would not be able to copy this symbolic link/file over to the rootfs and
executables would fail to load. Extend the search pattern to include all
ld*.so* files that could be needed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Refresh patches, delete patches that have been applied upstream.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix defaults]
The "new style" busybox applet approach moves all config and build
definitions related to an applet to its .c file. This makes the
patches easier to maintain, as they only add new files to the busybox
build directory, without modifying BusyBox files.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This fixes the following security problems:
CVE-2017-3731: Truncated packet could crash via OOB read
CVE-2017-3732: BN_mod_exp may produce incorrect results on x86_64
CVE-2016-7055: Montgomery multiplication may produce incorrect results
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not put the apex images into the kernel build directory as this directory
might get removed after kernel updates while the apex packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing u-boot images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This adds support for the PCB LEDs and Reset Button found on the PC
Engines APU2/APU3 embedded boards.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Updates to openvpn.init were included in early OpenVPN 2.4 patch
series, but got lost along the way and were never merged.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
HTB and TBF are the basic traffic shapers used by sqm-scripts. Moving
these into kmod-sched-core enables sqm-scripts to downgrade its
dependency from kmod-sched to kmod-sched-core, potentially making it
useful on devices with smaller flash sizes.
This adds around 30k to the size of kmod-sched-core (20k for sch_htb.ko
and 10k for sch_tbf.ko).
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This adds support for the SuperIO chip nct5104d found on the PC Engines
APU boards, which allows for a handful of additional ports, such as 2x
additional UART pinouts, enabling an external watchdog (no driver for
this functionality yet), and 16 GPIO pins. More info can be found at
https://pcengines.ch/ht_gpio.htm
Thanks to @feckert for helping package this.
Cc: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The name will appear in shell prompt and LuCI page title. Uppercase
letters seem to be more vigorous
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Update ubox to latest Git head in order to import the following fixes:
14839f0 kmodloader: make insert_module() idempotent
6e3c6dc kmodloader: add module alias awareness
9371411 kmodloader: fix out-of-bound access when parsing .modinfo
a62c946 kmodloader: modprobe: skip possible command line arguments
46a4b5f kmodloader: log to kmsg when loading directories of modules
eacc426 kmodloader: remove redundant glob wildcard char
8488bb5 ubox: Initialize conditionally uninitialized variable
db070f1 ubox: Fix some memory leaks
acc48b5 kmodloader: Fix typo in error message
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is how other Linux distributions are doing and kernel
modprobe_path[] of request_module() also has a default value of
/sbin/modprobe
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
A given signal-name is now converted to the corresonding number. In general
it's good style to use names (readability) and it's more portable: signal
numbers can be architecture-dependent, so we are more safe giving names.
A real world example is signal 10, which is BUS on ramips and USR1 on PPC.
All users of 'procd_send_signal' must change their code to reflect this.
Signed-off-by: Bastian Bittorf <bb@npl.de>
When relying on x.509 certs for auth and / or encryption of traffic you can't
use package openvpn-nossl.
Just have your package depend on openvpn-crypto to have SSL-encryption and
X.509-support enabled in OpenVPN. If encryption / X.509 is not a must, use
virtual packge openvpn, which is provided by all OpenVPN-variants.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
ap_setup_locked is named wps_ap_setup_locked in uci for consistency with other
wps related uci options.
Signed-off-by: Steven Honson <steven@honson.id.au>
The author of the upstream mwlwifi edited the history of the previous commit.
This commit not only fixes the updated hash but also sends in the latest
commits he made to the code which are mainly testing.
Signed-off-by: Gabe Rodriguez <lifehacksback@gmail.com>
Clarify opkg's messages related to downloads:
* more visible error message for package list download failure
* separate error message for signature file download error
* if wget returns 4, signal the network error more clearly
* remove '.' from end of filenames and URLs
* try signature check only if the package list was downloaded ok.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The radio would stop communicating completely. This issue was easiest to
trigger on AR913x devices, e.g. the TP-Link TL-WR1043ND, but other
hardware was occasionally affected as well.
The most critical issue was a race condition in disabling/enabling IRQs
between the IRQ handler and the IRQ processing tasklet
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All SPL variants are lzo compressed. The lzop binary is used for
compression but is not available in tools.
Additionally at least the NAND SPL support is broken and doesn't create
working bootloaders.
The fb3370 SPI NOR SPL enabled u-boot isn't required for LEDE since the
LEDE images are targeting the pre-installed EVA bootloader.
Mark these u-boot variants as well as the SPL variants for the
reference boards as broken till the lzma issues are fixed upstream and
we can use lzma instead of lzo compression.
Signed-off-by: Mathias Kresin <dev@kresin.me>
If only a single opkg control file exists (which can happen with
CONFIG_CLEAN_IPKG), grep would not print the file name by default. Instead
of forcing it using -H, we just switch to -l (print only file names) and
get rid of the cut.
Add -s to suppress an error message when no control files exist.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
There was a bug in brcmfmac patch that could result in treating random
memory as source of country codes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit c296ba834d.
According to several reports, the issues with the airtime fairness
changes are gone in current versions.
It's time to re-apply the patch now.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
accessing the u-boot's envs on this device is required to read the mac address.
These are the envs of the new u-boot, not of the stock one.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Instead of referencing u-boot packages from device profiles and having a
-all metapackage, make the u-boot packages hidden (they don't install to
bin/ anyway), and name the files in KERNEL_BUILD_DIR appropriately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
this commit allows to make a standalone u-boot for nsa310b.
While both first-stage and second-stage u-boot work fine if
installed to flash or loaded with kwboot,
I could not get stock u-boot nor bodhi's u-boot to chainload
any second stage u-boot (I also tried with dockstar's uboot
that works fine on this device if loaded with kwboot).
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
The subtarget on which the driver still depends was removed with
dee8986b95 because it was unmaintained
for a long time.
Signed-off-by: Mathias Kresin <dev@kresin.me>
