rework the dts to a common unifi-ac dtsi
pro network is connected via phy0 and has usb ports
lite network is connected via phy4 without usb ports
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
This target can automatically detect the correct memory size and we've
been using it for long in ar71xx.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Check if the GPIO is valid (or set at all). If no GPIO is set in the
devicetree, a gpiolib related kernel warning + stacktrace is shown during
boot and gpio-export reports GPIOs as exported albeit none really is.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The original device support patch configured the amber wlan LEDs (which
are meant as error indicator by the OEM) controlled by the SOC's GPIO
as wlan traffic indicators, as the correct white wlan LEDs are
connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were
not accessible. The recent addition of GPIO/ LED support to ath10k now
makes it possible to use the correct white LEDs instead - and
"mac80211: ath10k: use tpt LED trigger by default" also enables them by
default. While both LEDs are independent of each other (two separate
LEDs sharing one light tunnel), triggering both on wlan traffic is not
the intended behaviour (bright yellow light).
Tested on the ZyXEL NBG6817.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Move to i2c pins pinmux node to the pinctrl node.
Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")
Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The previous callback code was fragile, dependent on some UCI callback
bugs and side-effects now fixed in master commit 73d8a6ab.
Update scripts to use callbacks where appropriate and necessary, while
using normal UCI config parsing for all else. This results in smaller,
simpler, more robust code. Use callbacks in generate.sh to only process
'interface' defaults and the varying entries for 'reclassify', 'default'
and 'classify' sections. Also switch qos-stat to use non-callback UCI
handling.
The current changes work independently of 73d8a6ab (i.e. both before and
after), and are consistent with UCI config parsing documentation.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Remove the "firmware" partition definition from the DTS of R7800
to fix sysupgrade.
Commit 4645a6d3 defined CONFIG_MTD_SPLIT_UIMAGE_FW=y for ipq806x
and that causes mtd to misbehave as additional kernel and ubi
partitions are detected from inside the "firmware" partition.
[ 1.111324] 0x000001480000-0x000001880000 : "kernel"
[ 1.121005] 0x000001880000-0x000007900000 : "ubi"
[ 1.283912] 0x000007900000-0x000008000000 : "reserve"
[ 1.296407] 0x000001480000-0x000007900000 : "firmware"
[ 1.468043] no rootfs found after FIT image in "firmware"
[ 2.426860] 2 uimage-fw partitions found on MTD device firmware
[ 2.426931] 0x000001480000-0x000001880000 : "kernel"
[ 2.440420] 0x000001880000-0x000007900000 : "ubi"
Both kernel and ubi are already defined in DTS, so this duplication
leads into errors in sysupgrade:
Writing from <stdin> to kernel ...
ubiattach: error!: strtoul: unable to parse the number '6 mtd10'
ubiattach: error!: bad MTD device number: "6 mtd10"
The partition is defined to same area as kernel+ubi, and is not
needed for sysupgrade anymore. Remove it to fix things.
Only tested for the R7800 but all of them should behave equal.
Fixes: FS#1617
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[squashed commits, add "tested on" note]
Signed-off-by: Mathias Kresin <dev@kresin.me>
In order to be able to better compare files to sync in the future, include
all BIN_DIR subdirectories in the checksum calculation.
To not break existing applications, restrict the recursive checksumming to
CONFIG_BUILDBOT for now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are
orderd on the device as follows:
4 3 2 1 0
1-4: lan
0: wan
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
With current uboot default configuration the bootloader will
fail to start the OpenWrt firmware with the following error:
-----
unexpected character 'b' at the end of partition
Error initializing mtdparts!
incorrect device type in ubi
Partition ubi not found!
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
Error occured, error code = 112
-----
If the uboot configuration is examined with printenv
I can see that mdtparts line (on a nsa310) is wrong:
-----
mtdparts=mtdparts=orion_nand:0x0c0000(uboot),
0x80000(uboot_env),0x7ec0000(ubi)bootargs_root=
----
The "bootargs_root=" that was appended to it should not be there.
Fix the issue by adding a \0 line terminator at the end of affected lines,
mimicking what is also done by uboot upstream.
This issue was detected and confirmed on a nsa310, nsa325 and
a pogoplug v4, but it's not hardware-specific, so apply the same fix
to other devices as well.
Note that the issue is with the uboot's integrated boot configuration,
which is not used unless the uboot configuration in flash is unavailable
(erased or corrupted), which happens only on first time installation,
or if the user deletes the uboot configuration when upgrading uboot.
People just upgrading from an older uboot without erasing their previous
uboot configuration stored in flash would not have noticed this issue.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Add a menuconfig option to set the HOME_URL exposed in
/usr/lib/os-release independent from the
LEDE_DEVICE_MANUFACTURER_URL.
Fixes: FS#1123
Signed-off-by: Mathias Kresin <dev@kresin.me>
A new python script scripts/download.py is added to fetch tarballs using
GitHub archive API [1], then repack in a reproducible way same as the
current DownloadMethod/git
GitHub imposes a 60 reqs/hour rate limit on unauthenticated API
access[2]. This affects fetching commit date for feeding tar --mtime=
argument. However, observation indicates that archive download is NOT
subject to this limit at the moment. In the rare cases where download
fails because of this, we will falback to using DownloadMethod/git
The missing piece in the GitHub API is that it cannot provide in the
tarball dependent submodules's source code. In that case, the
implementation will also fallback to using DownloadMethod/git
[1] Get archive link, https://developer.github.com/v3/repos/contents/#get-archive-link
[2] Rate limiting, https://developer.github.com/v3/#rate-limiting
v2 <- v1:
- allow passing multiple urls with --urls argument
- add commit ts cache. can be helpful on retry
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
dfd9827 version: bump snapshot
88729f0 wg-quick: android: prevent outgoing handshake packets from being dropped
1bb9daf compat: more robust ktime backport
68441fb global: use fast boottime instead of normal boottime
d0bd6dc global: use ktime boottime instead of jiffies
18822b8 tools: fix misspelling of strchrnul in comment
0f8718b manpages: eliminate whitespace at the end of the line
590c410 global: fix a few typos
bb76804 simd: add missing header
7e88174 poly1305: give linker the correct constant data section size
fd8dfd3 main: test poly1305 before chacha20poly1305
c754c59 receive: don't toggle bh
Compile-tested-for: ath79 Archer C7 v2
Run-tested-on: ath79 Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
After a very enlightening but unfortunately far too short exchange with Jes
we mutually agreed to drop the patches. They are unfortunately not ready
yet.
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Add xt_bpf modules to {kmod-ipt,iptables-mod}-filter.
Match using Linux Socket Filter. Expects a BPF program in decimal
format. This is the format generated by the nfbpf_compile utility.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Refresh patches.
Remove patch that can be reverse applied:
mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch
mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch
Update patch that no longer applied:
ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch
Compiled-tested-for: lantiq, ramips
Run-tested-on: lantiq BT hh5a, ramips MIR3g
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Michael Yartys <michael.yartys@protonmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Netgear WNR612 v2:
- cpu Atheros AR7240 (Python) @400MHz
- flash 4MB
- ram 32MB
- ethernet 10/100: 1xwan + 2xlan (only two)
- radio AR9285
As there is a rebranded WNR612v2 called ON Networks N150R, add
a dtsi which includes all device support, and add a separate dts
for the device only (with a separate one for the subsequent N150R).
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Have mktplinkfw fill in the rootfs offset so the firmware splitter can
find it without aligning to erase blocks.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Add support to dynamically split the firmware partition into os-image
and file-system partitions. This is done by replacing those entries in
the partition table with a single unified firmware partition, which is
then split according to actual kernel image size.
The factory image will have the file-system partition aligned to a 64K
erase block, but the sysupgrade image skips this and aligns only the
JFFS2 EOF marker to squeeze out more space.
This should prevent further creeping updates to the kernel partition
size while maximizing space for the overlay filesystem on smaller
devices.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Add an option (-O) to calculate rootfs offset for combined images.
This is needed for the TP-Link mtdsplit driver to locate the rootfs
when the start is not aligned to an erase block. This will be the
case for sysupgrade images produced by tplink-safeloader with upcoming
dynamic partition splitting.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Commit 61d57a2f88 adds ath10k LED
support, but doesn't add an option to actually enable it.
After enabling this option, a LED named ath10k-phy0 appears in sysfs,
and a trigger can be assigned to it. Since 60deb3cdef the default set
trigger is the tpt one.
Enable it by default, as most devices using ath10k chips shouldn't be
severely space-constrained. There are likely many devices that can
benefit from having it enabled, like my testing device.
Before:
text data bss dec hex filename
245311 8899 16 254226 3e112 ath10k_core.ko
After:
text data bss dec hex filename
245979 8899 16 254894 3e3ae ath10k_core.ko
Tested on a D-Link DAP-2695-A1 (ar71xx).
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use the tpt LED trigger for each created phy led. Ths way LEDs attached
to the ath10k GPIO pins are indicating the phy status and blink on
traffic.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specification:
- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0
Preparing a TFTP recovery image for initial flashing:
Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!
Create a TFTP recovery image:
1) Download a stock TP-Link Firmware file here:
https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
#> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
#> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin
The resulting image can be flashed via TFTP recovery mode.
Flash instructions:
1) To flash the recovery image, start a TFTP server from IP address
192.168.0.66 and serve the recovery image named
ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
and power it up. Keep pressing the WPS/Reset button for 10 seconds.
It will try to download the recovery image and flash it.
It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
The rtl8367b driver never supported a mdio property and it is quite
likely that the switch never worked for the board.
Use the mii-bus property instead to manage the switch via a mdio bus.
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
Differing from all other archs supported by musl, MIPS defines SO_PEERSEC
to 30 instead of 31.
Patch has also been submitted upstream.
Reported-by: Andrey Jr. Mlenikov <temnota.am@gmail.com>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add support for detecting TP-Link Pharos v2 boards.
They use different format in product-info partition than v1 boards.
Code was written mostly by Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch kernel patches
break the possibility for using an ip4ip6 tunnel interface as a fall
back interface accepting ip4-in-ip6 tunneled packets from any remote
address. This works out of the box with any normal (non-666-patched)
kernel and can be configured by setting up an 'ip -6 tunnel' with type
'any' or 'ip4ip6' and a remote address of '::'.
The misbehavior comes with line 290 the patch which discards all packets
that do not show the expected saddr, even if no single fmr rule was
defined and despite the validity of the saddr was already approved earlier.
Signed-off-by: Axel Neumann <neumann@cgws.de>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
This commit adds support for the MT7623A-based UniElec U7623-02 router,
with eMMC storage and 512MB RAM. The router can be delivered with NAND
Flash and more memory, but I only have access to the one configuration.
The DTS is structured in such a way that adding support for
more/different storage/memory should be straight forward.
The device has the following specifications:
* MT7623A (quad-core, 1.3 GHz)
* 512MB RAM (DDR3)
* 8GB storage (eMMC 4.5)
* 2x normal miniPCIe slots
* 1x miniPCIe slot that is connected via an internal USB OTG port
* 5x 1Gbps Ethernet (MT7530 switch)
* 1x UART header
* 1x USB 3.0 port
* 1x SATA 3.0
* 1x 40P*0.5mm FPC for MIPI LCD
* 1x SIM slot
* 12x LEDs (2 GPIO controlled)
* 1x reset button
* 1x DC jack for main power (12V)
The following has been tested and is working:
* Ethernet switch
* miniPCIe slots (tested with Wi-Fi cards)
* USB 3.0 port
* sysupgrade
* reset button
Not working:
* The miniPCIe connected via USB OTG. For the port to work, some MUSB
glue must be added. I am currently in the process of porting the glue
from the vendor SDK.
Not tested:
* SATA 3.0
* MIPI LCD
Installation:
The board ships with u-boot, and the first installation needs to be done
via the bootloader using tftp. Step number one is to update the MBR of
the eMMC, as the one that ships with the device is broken. Since the
device can ship with different storage sizes, I will not provide the
exact steps for creating a valid MBR. However, I have made some
assumptions about the disk layout - there must be one 8MB recovery
partition (FAT32) and a partition for the rootfs (Linux).
The board loads the kernel from block 0xA00 (2560) and I have reserved
32MB for the kernel (65536 blocks). I have aligned the partitions on the
erase block size (4096 byte), so the recovery partition must start on
block 69632 and end on 86016 (16385 sectors). The rootfs is assumed to
start on sector 90112.
In order to install the mbr, you run the following commands from the
u-boot command line:
* tftpboot ${loadaddr} <name of mbr file>
* mmc device 0
* mmc write ${loadaddr} 0x00 1
Run the following commands to install + boot OpenWRT:
* tftpboot ${loadaddr} openwrt-mediatek-mt7623-7623a-unielec-u7623-02-emmc-512m-squashfs-sysupgrade-emmc.bin.gz
* run boot_wr_img
* run boot_rd_img
* bootm
Recovery:
In order to recover the router, you need to follow the installation
steps above (no need to replace MBR).
Notes:
* F2FS is used as the overlay filesystem.
* The device does not ship with any valid MAC address, so a random
address has to be generated. As a work-around, I write the initial
random MAC to a file on the recovery partition. The MAC of the WAN
interface is set to the MAC-address contained in this file on each boot,
and the address of the LAN-interfaces are WAN + 1. The MAC file is kept
across sysupgrade/firstboot.
My approach is slightly different than what the stock image does. The
first fives bytes of the MAC addresses in the stock image are static,
and then the last byte is random. I believe it is better to create fully
random MAC addresses.
* In order to support the miniPCIe-slots, I needed to add missing
pcie-nodes to mt7623.dtsi. The nodes are just c&p from the upstream
dtsi.
* One of the USB3.0 phys (u3phy2) on the board can be used as either USB
or PCI, and one of the wifi-cards is connected to this phy. In order to
support switching the phy from USB to PCI, I needed to patch the
phy-driver. The patch is based on a rejected (at least last time I
checked) PCI-driver submitted to the linux-mediatek mailing list.
* The eMMC is configured to boot from the user area, and according to
the data sheet of the eMMC this value can't be changed.
* I tried to structure the MBR more nicely and use for example a
FAT32-parition for the kernel, so that we don't need to write/read from
some offset. The bootloader does not support reading from
FAT32-paritions. While the command (fatload) is there, it just throws an
error when I try to use it.
* I will submit and hope to get the DTS for the device accepted
upstream. If and when that happens, I will update the patches
accordingly.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
