the old FE_INT_STATUS register becomes two registers.
FE_INT_STATUS and INT_STATUS. so the hw status almost full
must change to read from FE_INT_STATUS register.
tx/rx done read from INT_STATUS register.
mt7620 datasheet define CNT_GDM1_AF at BIT(29).
but after test it should be BIT(13). why?
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44371
- budget is decremented with completed frames, so don't check if done is
smaller
- ACK the interrupt before processing further frames to fix a small race
condition.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44234
The mac address usually write in factory block. but sometime user erase this block , the mac address will change to ff:ff:ff:ff:ff:ff.
This patch is purpose to fix this issue.
Signed-off-by: wengbj <linux.c@foxmail.com>
SVN-Revision: 44166
* fix TSO features verify on mt7621 firewrt board
* improve tx clean up. no need to access uncached
memory. also use TX_DTX register instead of
read tx ring DONE bit
* mt7621 need napi weight 64 to get more performance
* remove netif_receive_skb, after kernel version
3.7 tcp4_gro_receive can handle tcp checksum.
on rt2880 use iperf tcp LAN to WAN throughput test.
with gro 135 Mbits/sec. without gro 80.4Mbits/sec.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44118
on mt7621 don't have tx vlan vid registers.
so set FE_REG_FE_DMA_VID_BASE to 0.
set rx vlan offload register to disable.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44117
the rx_buf_size now is 1534 when mtu is 1500.
the ethernet frame with vlan tag and FCS is 1522.
so the buffer is enough.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44116
* use default timeout value
* print more debug ring info
* move timeout reset function to workqueue
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44043
hardware status and tx vlan offload support on all targets
except rt5350. so i modify the IS_ENABLE condition only for
mt7621.
support mt7621 hardware status reference by SDK. but i don't
have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE
to 0 to let software count.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43303
hardware tx vlan offload only support max 16 vids
now use add/delete vlan interface to update vlan id table
when duplicate vlan id index detect.
disable hardware tx vlan offload support.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43301
the SDK does a bit of extra init that we did not do yet when using an external mt7530.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43245
r43200 tries to detect if the fixup is needed or not. control the behaviour via
OF instead and disable unused ports.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43201
add ALL5003 to board description in mach-all5002.c
adapt detection in user-space accordingly
(no functional changes)
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35851
Ralink RT3052F, 4MB flash, 32MB ram, one USB 2.0, two buttons
and seven leds.
Factory image should be used to flash from original firmware.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35244
