Commit graph

2524 commits

Author SHA1 Message Date
Felix Fietkau
5343c7694e ar71xx: enable usb quirks for all chipidea based devices
The most important one is qca_force_host_mode, which also sets the
'Stream Disable' bit in the usbmode register.

Fixes usb stability issues on AR933x and AR7241/AR7242

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40841
2014-05-24 08:01:42 +00:00
Felix Fietkau
83dc560621 ar71xx: fix typo in tl-wr710n mac setup (fixes #16469)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40840
2014-05-24 08:01:33 +00:00
Hauke Mehrtens
f5e5477c81 kernel: modify mtd related patches for 3.14
The change is the same as ("kernel/generic: modify mtd related
patches"). Since these files are under files directory, not a files
directory of specific kernel version, better to also change them. So
it will avoid adding files to future specific files directory
(e.g. files-3.14) for this mtd related change.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>

SVN-Revision: 40732
2014-05-08 21:52:04 +00:00
Felix Fietkau
b4d93a52cf ar71xx/ath9k: fix reading the WMAC revision on AR953x (fixes #15581)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40695
2014-05-04 23:26:20 +00:00
Gabor Juhos
1374e5a721 ar71xx: rb91x: fix ethernet packet loss issues
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.

Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40509
2014-04-13 20:41:52 +00:00
Gabor Juhos
46a8af4c47 ar71xx/mikrotik: enable the AT803x PHY driver
It will be used on the RB91x boards.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40508
2014-04-13 20:41:51 +00:00
Gabor Juhos
02ea5b9e56 ar71xx: allow to configure AR803x PHYs via platform data
Add a patch for the at803x phy driver, in order to be able
to configure some register settings via platform data.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40507
2014-04-13 20:41:50 +00:00
Gabor Juhos
27dec09907 ar71xx: add phy_mmd_{read,write} helpers
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40506
2014-04-13 20:41:48 +00:00
Gabor Juhos
6a0f8ea201 ar71xx: enable console on the RB91x boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40505
2014-04-13 20:41:42 +00:00
Gabor Juhos
0d7197116e ar71xx: add profile and build image for the ZyXEL NBG6716 board
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: remove the non-existing zyxelnand subtarget specific stuff]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40502
2014-04-13 08:29:09 +00:00
Gabor Juhos
ecec091d33 ar71xx: add user-space support for the ZyXEL NBG6716 board
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40500
2014-04-13 08:29:07 +00:00
Gabor Juhos
a5e398abad ar71xx: add kernel support for ZyXEL NBG 6716
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot

Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
  - rename and refresh kernel patch,
  - fix a few typos,
  - change button key codes,
  - use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40499
2014-04-13 08:29:05 +00:00
Gabor Juhos
22916814e3 ar71xx: build firmware image for the WNDR3700 v4 board
Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40481
2014-04-12 20:22:41 +00:00
Gabor Juhos
a67578ce33 ar71xx/image: allow to use more arguments for some macros
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40480
2014-04-12 20:00:37 +00:00
Gabor Juhos
4149ab5193 ar71xx: wndr4300: indicate WNDR3700v4 in the kernel support files
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40479
2014-04-12 19:58:23 +00:00
Gabor Juhos
7b85e2e527 ar71xx: wndr4300: enable 5V power for the USB port
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.

Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40478
2014-04-12 19:58:20 +00:00
Gabor Juhos
ed72141fd4 ar71xx: wndr4300: use KEY_RFKILL code for the Wireless button
Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40477
2014-04-12 17:53:34 +00:00
Gabor Juhos
b971a4b5b9 ar71xx: add default LED config for WiFi LEDs on the WNDR4300
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40476
2014-04-12 17:42:36 +00:00
Gabor Juhos
4fe71cedfe ar71xx: wndr4300: add LED for 2.4Ghz wifi interface
Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40475
2014-04-12 17:42:35 +00:00
Gabor Juhos
db123a8a21 ar71xx: wndr4300: select GPIO_OUT functionality for LED GPIOs
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40474
2014-04-12 17:42:34 +00:00
Gabor Juhos
9b7b57aeb4 ar71xx: wndr4300: change 'orange' to 'amber' in LED color names
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.

Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40473
2014-04-12 17:42:33 +00:00
Gabor Juhos
a93c87d772 ar71xx: fix typos in TP-Link rssileds definition
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5109/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40472
2014-04-12 16:01:45 +00:00
Gabor Juhos
087547d3e2 ar71xx: add rssileds for Ubiquiti XM boards
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40471
2014-04-12 16:01:43 +00:00
Gabor Juhos
d2812cb036 kernel: update 3.10 to 3.10.36
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40467
2014-04-12 11:59:07 +00:00
Gabor Juhos
17f848538c ar71xx: fix image generation
Move the comments out from the shell script to fix build
breakage introduced in r40464.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40466
2014-04-12 11:59:05 +00:00
Gabor Juhos
cd75606712 ar71xx: avoid spurious restarts caused by the watchdog on AR934x
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40465
2014-04-12 10:21:04 +00:00
Gabor Juhos
fd53cfa31b ar71xx: add comments for image Makefile.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5075/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40464
2014-04-12 09:52:58 +00:00
Gabor Juhos
1bce5e8328 ar71xx: initial support for TP-Link Archer C7v2
The C7v2 has 16 MB flash and QCA9880-BR4A rev 2 supported by ath10k driver.
The C7v1 had 8 MB flash and the unsupported QCA9880-AR1A rev 1.

Signed-off-by: Adam Serbinski <adam@serbinski.com>
Patchwork: http://patchwork.openwrt.org/patch/5071/
[juhosg:
 - remove the v2 specific profile add the ath10k driver to the existing
   Archer C7 profile instead. Although on v1 devices it does not change
   the non-working behaviour, but the ath10k driver is useful for users
   whom have replaced the wifi card with a supported one in their units.
 - update image/Makefile to build firmware image for both boards if the
   Archer C7 profile is selected]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40463
2014-04-12 09:52:54 +00:00
Felix Fietkau
8be7f487e2 ar71xx: move some always-used led related functionality from kmod packages to the kernel image
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40413
2014-04-07 10:44:52 +00:00
Felix Fietkau
4a9ea80ef0 /lib/functions.sh: move rarely used mtd and macaddr related functions to /lib/functions/system.sh
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40411
2014-04-07 10:29:47 +00:00
Felix Fietkau
7131a104f5 ar71xx: add support for the TP-LINK TL-WR841N/ND v9
Everything seems to be working fine. Potential issues:

* VLAN port IDs are reversed with regard to the numbers on the case.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 40400
2014-04-07 08:00:02 +00:00
Felix Fietkau
f80f0c7d22 ar71xx: add support for QCA953x SoC
I don't have access to the specs, so I'm not sure about every detail, but I
haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty
much like a QCA955x without PCI, a little twist in the clock calculation and
a AR9331-compatible switch.

Features not yet supported:

* EHCI (my test system doesn't have USB)
* ? (I have no idea if the QCA953x has any other features I don't know about
that aren't used by the TL-WR841N v9)

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 40399
2014-04-07 07:59:45 +00:00
Gabor Juhos
627baa28d3 kernel: update 3.10 to 3.10.34
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40291
2014-03-27 09:28:33 +00:00
Gabor Juhos
b68564ed3f ar71xx: build image for TL-WDR4300v1 (IL)
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.

Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40038
2014-03-27 06:36:59 +00:00
Gabor Juhos
4ea54b827f ar71xx: add profile and build firmware image for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40036
2014-03-27 06:36:57 +00:00
Gabor Juhos
02f2e90d5f ar71xx: add user space support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: use correct board name in uci-defaults/02_network]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40033
2014-03-27 06:36:47 +00:00
Gabor Juhos
5256bbdc56 ar71xx: add kernel support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
 - use a separate patch for kernel changes,
 - reorder Kconfig and Makefile entries,
 - change function and variable names to be lowercase only
   and fix misaligned tabs in mach-gs-oolite.c,
   ... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40032
2014-03-27 06:36:46 +00:00
Gabor Juhos
f0dc89b46f ar71xx: rename RB951Ui specific kernel patch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40031
2014-03-27 06:35:55 +00:00
Gabor Juhos
47dfbb5bc6 ar71xx: rb95x: use correct SPI flash address
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.

Compile tested only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39891
2014-03-12 12:52:39 +00:00
Gabor Juhos
25e870eed6 ar71xx: ar934x_nfc: fix memory initialization bug
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type)  * array_size   should be used in memset.

Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39890
2014-03-12 12:52:36 +00:00
Felix Fietkau
802d17ceaf ar71xx: Add 16MB Flash version for Embedded Wireless Dorin Platform
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>

SVN-Revision: 39764
2014-02-28 11:08:14 +00:00
Felix Fietkau
d83750083d ar71xx: adjust ew-dorin platform for LAN+WAN setup
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>

SVN-Revision: 39763
2014-02-28 11:08:04 +00:00
Gabor Juhos
e9c80a1224 ar71xx: fix failsafe acces on several devices
The ar71xx platform always uses the eth0 interface to provide
access to the device in failsafe mode. Due to this, failsafe
access is broken on devices where the LAN ports are connected
to the 'eth1' interface.

Update the relevant script to correctly set the ifname variable
for these devices.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39752
2014-02-25 17:40:04 +00:00
Gabor Juhos
f677b1bc7e kernel: update 3.10 to 3.10.32
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39707
2014-02-23 10:59:40 +00:00
Gabor Juhos
590bafe3de ar71xx: define status LED for the RB91x boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39705
2014-02-23 08:11:54 +00:00
Gabor Juhos
da2f3c1448 ar71xx: rb91x: register GPIO LEDs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39704
2014-02-23 08:11:53 +00:00
Gabor Juhos
14d95026b2 ar71xx: rb91x: add SPI device for the serial shift register
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.

Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39703
2014-02-23 08:11:52 +00:00
Gabor Juhos
7b89005f0d ar71xx/mikrotik: enable the 74x164 GPIO driver
That will be used to drive the 74HC595 serial-in/parallel-out
8-bits shift register which can be found on some RouterBOARDs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39702
2014-02-23 08:11:50 +00:00
Gabor Juhos
5f224ef8a3 ar71xx: improve platform device support in the gpio-74x164 driver
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39701
2014-02-23 08:11:49 +00:00
Gabor Juhos
3d906ac6ac ar71xx: rb91x-nand: rewrite to use GPIO API
Rewrite tha rb91x-nand driver to use GPIO API to
modify the NAND control lines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39700
2014-02-23 07:19:32 +00:00
Gabor Juhos
8fea668cb7 ar71xx: rb91x: register a gpio-latch platform device
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39699
2014-02-22 18:05:32 +00:00
Gabor Juhos
da5caba072 ar71xx/mikrotik: enable the GPIO latch driver
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39698
2014-02-22 18:05:31 +00:00
Gabor Juhos
ab08c40487 ar71xx: add a generic GPIO latch driver
It will be used for the Mikrotik boards.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39697
2014-02-22 18:05:29 +00:00
Gabor Juhos
be18a3849b ar71xx/mikrotik: enable small sector erase in the m25p80 driver
The serial flash devices used on the ROuterBOARDs are
supporting 4KiB erase blocks. Enable the small sector
erase option in the m25p80 driver to avoid superfluous
erase/write of adjacent blocks.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39696
2014-02-22 16:26:55 +00:00
Gabor Juhos
b7539ab109 ar71xx: spi-ath79: fix initial GPIO CS line setup
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39695
2014-02-22 16:17:28 +00:00
Gabor Juhos
3e6c7ed4f2 ar71xx: refresh unaligned access hacks patch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39694
2014-02-22 16:17:27 +00:00
Gabor Juhos
4e0309630b ar71xx: rb91x: fix pll_1000 value for eth0 to avoid packet loss
When the RB91x device uses a GbE link the connection
suffers from packet loss:

  root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 20 -q
  PING 192.168.1.254 (192.168.1.254): 65507 data bytes

  --- 192.168.1.254 ping statistics ---
  20 packets transmitted, 9 packets received, 55% packet loss
  round-trip min/avg/max = 4.570/4.815/4.999 ms

Using a different PLL value fixes the issue.

  root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 100 -q
  PING 192.168.1.254 (192.168.1.254): 65507 data bytes

  --- 192.168.1.254 ping statistics ---
  100 packets transmitted, 100 packets received, 0% packet loss
  round-trip min/avg/max = 4.449/5.413/13.870 ms

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39642
2014-02-20 17:07:56 +00:00
Gabor Juhos
d19b868b12 ar71xx: Add support for MikroTik RB951Ui-2HnD
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result.  I have cleaned up this patch.

When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.

This patch applies cleanly to SVN 39392.

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
  - drop the 'rb951ui_wlan_init' function and rework the code to
    use the recently introduced rb95x_wlan_init function instead,
  - fix GPIO number of the port5 LED,
  - rename LEDs according to the standard LED naming conventions,
    and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39641
2014-02-20 17:07:51 +00:00
Gabor Juhos
f433088d50 ar71xx: add profile and build image for TP-Link TL-WDR4900 v2.0 board
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4850/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39637
2014-02-19 12:15:35 +00:00
Gabor Juhos
7ec2d80ae3 ar71xx: add user-space support for TP-Link TL-WDR4900 v2.0 board
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4849/
[juhosg:
  - use the Archer C7 specific LED setup instead of adding
    identical code]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39636
2014-02-19 12:15:34 +00:00
Gabor Juhos
db0e6e264d ar71xx: add kernel support for the TP-Link TL-WDR4900 v2.0 board
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4848/
[juhosg:
  - rename and refresh kernel patch,
  - merge the board setup code into mach-archer-c7.c and drop
    mach-tl-wdr49000-v2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39635
2014-02-19 12:15:32 +00:00
Gabor Juhos
6b8eb55ddb ar71xx: fix unaligned access hacks for tcp timestamps
This missing bit of the hack saves hugely on instruction traps
on tcp connections to ar71xx based routers.

Patch-by: Dave Taht <dave.taht@bufferbloat.net>
Patchwork: http://patchwork.openwrt.org/patch/4905/
[juhosg: adjust subject, refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39626
2014-02-18 17:34:17 +00:00
Gabor Juhos
d6cb5215a9 ar71xx: WNR2200: fix mounting root fs problem
Solves ticket #14356 <https://dev.openwrt.org/ticket/14356>

Without this patch, UART output will show only 4 partitions:
  [    0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
  [    0.750000] Creating 4 MTD partitions on "spi0.0":
  [    0.750000] 0x000000000000-0x000000050000 : "u-boot"
  [    0.760000] 0x000000050000-0x000000070000 : "u-boot-env"
  [    0.770000] 0x000000070000-0x0000007f0000 : "firmware"
  [    0.790000] 0x0000007f0000-0x000000800000 : "art"
and then linux complains :VFS: Cannot open root device "(null)"

With this patch, UART out will show 7 partitions:
  [    0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
  [    0.750000] Creating 4 MTD partitions on "spi0.0":
  [    0.750000] 0x000000000000-0x000000040000 : "u-boot"
  [    0.760000] 0x000000040000-0x000000050000 : "u-boot-env"
  [    0.770000] 0x000000050000-0x0000007f0000 : "firmware"
  [    0.780000] 2 netgear-fw partitions found on MTD device firmware
  [    0.780000] 0x000000050000-0x00000014b440 : "kernel"
  [    0.790000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  [    0.800000] 0x00000014b440-0x0000007f0000 : "rootfs"
  [    0.810000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  [    0.820000] mtd: device 4 (rootfs) set to be root filesystem
  [    0.830000] 1 squashfs-split partitions found on MTD device rootfs
  [    0.830000] 0x000000340000-0x0000007f0000 : "rootfs_data"
  [    0.840000] 0x0000007f0000-0x000000800000 : "art"

This patch is tested against r39502 of trunk.

Signed-off-by: Jonathan Chang <changcs@santos.ee.ntu.edu.tw>
Patchwork: http://patchwork.openwrt.org/patch/4870/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39625
2014-02-18 17:34:16 +00:00
Jo-Philipp Wich
b1d7ebae09 ar71xx: fix mtdpartsize macro in image Makefile (#14961)
The mtdpartsize macro triggers shell errors on various Linux distributions
when the partname argument $(1) does not appear within the partmap $(2).

Change the sed pattern to only emit anything if a successful substitution
occured and only evaluate the arithmetic expression if something was printed
by the sed program.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 39583
2014-02-13 21:19:00 +00:00
Gabor Juhos
037b42838f ar71xx: dragino2: add missing sysupgrade support.
The original dragino2 board support was missing some changes from the
upstream svn repository (http://svn.dragino.com/dragino2) that supported
sysupgrade.

[juhosg: change subject]

Signed-off-by: Karl Palsson <karlp@remake.is>
Patchwork: http://patchwork.openwrt.org/patch/4801/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39429
2014-01-30 17:08:02 +00:00
Gabor Juhos
3b8c51771d ar71xx: wpe72: set active_low flag for the reset button
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39401
2014-01-26 14:55:34 +00:00
Gabor Juhos
b503dc026e ar71xx: wp543: set active_low flag for the buttons
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39400
2014-01-26 14:55:32 +00:00
Gabor Juhos
a2543d72d8 kernel: update 3.10 to 3.10.28
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39399
2014-01-26 11:30:34 +00:00
Gabor Juhos
e41e531e3b ar71xx: image: reserve 4 erase blocks on the TP-Link devices
This ensures that the generated images will have enough erase
blocks for JFFS2.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39397
2014-01-25 18:12:13 +00:00
Gabor Juhos
50f38063cd ar71xx: archer c7: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39395
2014-01-25 11:16:59 +00:00
Gabor Juhos
f1a9ed8345 ar71xx: image: move WNDAP360 macro
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39394
2014-01-25 08:31:45 +00:00
Gabor Juhos
f85231257e ar71xx: fix bad RX sensitivity on newer TL-WDR4300 boards
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.

Setup the GPIOs of the external LNAs to fix the issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39392
2014-01-24 17:40:17 +00:00
Gabor Juhos
09bf46d418 ar71xx: image: generate sysupgrade images for the Compex boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39391
2014-01-24 17:15:03 +00:00
Gabor Juhos
252e906dda ar71xx: add sysupgrade support for the Compex boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39390
2014-01-24 17:15:02 +00:00
Gabor Juhos
0c0b87293e ar71xx: image: use a single firmware partition on Compex devices
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39389
2014-01-24 17:15:01 +00:00
Gabor Juhos
2995030b47 ar71xx: enable MTD_SPLIT_LZMA_FW option
It will be used for Compex devices.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39388
2014-01-24 17:15:01 +00:00
Gabor Juhos
998c89a9a6 ar71xx: image: detect partition sizes in the Image/Build/Ath macro
Get the size of the mtd partitions directly from the
MTD layout and remove the superfluous macro parameters.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39384
2014-01-24 11:59:35 +00:00
Gabor Juhos
4556632578 ar71xx: image: fix size verification in the CatFiles macro
The macro checks the size of the rootfs image even if
the second parameter of the macro contains the size of
an eraseblock. It is wrong because the size of the
kernel image will be adjusted to the next eraseblock
and the resulting image might be too large.

Fix the macro to check the size of the final image
instead of the rootfs image.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39383
2014-01-24 11:59:32 +00:00
Gabor Juhos
56136c0f34 ar71xx: ap83: define mtd layout via command line
Also use the RKuImage macro becasue the original
firmware starts with the rootfs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39379
2014-01-23 16:47:42 +00:00
Gabor Juhos
a59e82761f ar71xx: ap81: define mtd layout via command line
Also use the RKuImage macro becasue the original
firmware starts with the rootfs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39378
2014-01-23 16:47:41 +00:00
Gabor Juhos
9f4e2bf326 ar71xx: image: show size limit in warning messages
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39376
2014-01-23 12:27:28 +00:00
Gabor Juhos
447530995a ar71xx: add initramfs image support for Compex devices
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39375
2014-01-23 12:23:10 +00:00
Gabor Juhos
b629009eaa ar71xx: wp543: use KEY_RESET code for the sw4 button
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39374
2014-01-23 12:23:08 +00:00
Luka Perkov
cbc892a549 ar71xx: create wndr3700 network config from uci-defaults
Since that was the last configuration in defconfig directory we can drop the
defconfig init script too.

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 39373
2014-01-23 11:33:42 +00:00
Gabor Juhos
0b599c51cc ar71xx: mynet-n750: define LEDs connected to the AR8327 switch
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4743/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39361
2014-01-21 17:17:42 +00:00
Gabor Juhos
506b40b628 ar71xx: tl-wr1043nd-v2: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39346
2014-01-20 10:23:06 +00:00
Gabor Juhos
c17cfab560 ar71xx: tl-wdr4300: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39345
2014-01-20 10:23:05 +00:00
Gabor Juhos
db5f22a2d7 ar71xx: set default LED config for the RB2011* boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39344
2014-01-20 10:23:04 +00:00
Gabor Juhos
927809e59b ar71xx: set status_led for the RB2011* boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39343
2014-01-20 10:23:03 +00:00
Gabor Juhos
07f76a164a ar71xx: fix indentation in diag.sh
Replace the leading spaces with tabs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39342
2014-01-20 10:23:02 +00:00
Gabor Juhos
4c54635106 ar71xx: rb2011: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39341
2014-01-20 10:23:01 +00:00
Gabor Juhos
31d6ad289f ar71xx: enable AR8327 LED support
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39340
2014-01-20 10:23:00 +00:00
Gabor Juhos
b4dc45e07d ar71xx: rb2011: fix eth5 LED
The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39335
2014-01-20 10:22:49 +00:00
Imre Kaloz
b6e1cbd8dd generate images for the On Networks N150 (rebranded Netgear WNR612v2)
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 39320
2014-01-18 19:44:40 +00:00
Gabor Juhos
0e2586a774 kernel: update 3.10 to 3.10.26
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39220
2014-01-11 16:06:37 +00:00
Gabor Juhos
30ebad2dee ar71xx: ag71xx: increase calculated max frame length value
The r39147 commit introduces a regression: at lease on some routers
with ar8216 switch large packets get lost if 802.1q tagged port is
used on the interface connected to the aforementioned switch.

The r39147 changes code in the way so interface is set to accept
packets no longer than max ethernet frame length for a given mtu.

Unfortunately ar8216 has a feature: it sends two additional bytes
as a packet header and those this header needs to be added to the
max frame length. Otherwise long enough packets get lost.

The problem only manuifests itself if interface is used in vlan
tagged mode. If interface is untagged then ar8216's header fits
into space used by 802.1q tag and not packets are lost.

Include two additional bytes in the max frame length calculation
to fix the issue.

This patch is tested and works with Trendnet TEW-632BRP.

Signed-off-by Nikolay Martynov <mar.kolya@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4656/
[juhosg:
  - simplify the patch to include the additional bytes of the
    switch header unconditionally,
  - change subject and update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39219
2014-01-11 11:15:30 +00:00
Gabor Juhos
c977d49a29 ar71xx: my net n750: simplify LNA GPIO setup
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39217
2014-01-10 09:37:59 +00:00
Gabor Juhos
cc3beb9c76 ar71xx: my net n600: simplify LNA GPIO setup
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39216
2014-01-10 09:37:58 +00:00
Gabor Juhos
182e8ef949 ar71xx: add a helper function for external LNA GPIO setup
The built-in wireless MAC of the AR934x SoC can handle
external LNAs and the control signal of the LNAs can be
routed to any GPIO line. Add a helper function which
can be used to configure the GPIO lines.

The helper function will be used for AR934x boards
which are using externel LNAs to improve sensitivity.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39215
2014-01-10 09:37:57 +00:00
Gabor Juhos
32aef686f7 ar71xx: Fix WD My Net N600 weak signal issue
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.

Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
  - remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
  - change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39214
2014-01-10 09:07:12 +00:00
Gabor Juhos
01727717f7 ar71xx: Fix WD My Net N750 weak signal issue
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.

Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39213
2014-01-10 09:07:11 +00:00
Gabor Juhos
05f8604e2e ar71xx: fix max frame length of the QCA955x SoCs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39161
2013-12-23 17:05:23 +00:00
Gabor Juhos
76f37c5d46 ar71xx: don't set builtin_switch flag for QCA9558
It makes no sense, the SoC has no built-in switch.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39160
2013-12-23 17:05:21 +00:00
Gabor Juhos
f2cd3399f7 ar71xx: allow to use large ethernet frames on AR934x SoCs
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.

Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39149
2013-12-20 11:41:23 +00:00
Gabor Juhos
2b220f3550 ar71xx: ag71xx: fix max frame length setup of the built-in switches
The currently used bitmask of the maximum frame length field
is wrong for both models. On AR724x/AR933x the largest frame
size is 2047 bytes, on the AR934x it is 16383 bytes.

Make the MTU setup code model specific, and use the correct
bitmask for both models. Also change the value to the maximum.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39148
2013-12-20 11:41:22 +00:00
Gabor Juhos
35d601f974 ar71xx: ag71xx: calculate max frame len register value from the MTU
Set the MAX_FRAME_LEN register to zero in ag71xx_hw_init()
and write the correct value into that from the ag71xx_open()
and ag71xx_fast_reset() functions.

Also recalculate the RX buffer size based on the actual
maximum frame length value to optimize memory allocation.
Additionaly, disallow to change the MTU value while the
interface it running.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39147
2013-12-20 11:41:20 +00:00
Gabor Juhos
9e7d77de2d ar71xx: ag71xx: add ag71xx_max_frame_len() helper
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39146
2013-12-20 11:41:18 +00:00
Gabor Juhos
2c4e3cf33a ar71xx: ag71xx: get max_frame_len and desc_pktlen_mask from platform data
This will allow to use SoC specific values for both.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39145
2013-12-20 11:41:17 +00:00
Gabor Juhos
9be1e508f9 ar71xx: ag71xx: store descriptor packet length mask in ag71xx struct
The currently used bitmask is not correct for all SoCs.
Introduce a new field in struct ag71xx and store the
bitmask in that. Use the current value for now, it will
be adjusted for each SoCs in further patches.

Aslo use the new field directly in the ag71xx_rx_packets
and ag71xx_hard_start_xmit() functions and remove the
ag71xx_desc_pktlen() helper.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39144
2013-12-20 11:41:16 +00:00
Felix Fietkau
a787a02873 ar71xx: add missing tx gain table flag for buffalo wzr-hp-g450h
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39139
2013-12-19 17:18:12 +00:00
Gabor Juhos
2318a46d84 ar71xx: enable images for WD My Net N750
Now that the switch works correctly we can enable the images for this
board.

Flashing from the factory firmware, the factory failsafe loader and
sysupgrade was tested successfully.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4617/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39130
2013-12-17 22:14:13 +00:00
Gabor Juhos
1ebf211340 ar71xx: fix WD My Net N750 switch led cfg
Now that the switch is working correctly I had the chance to actually
test the LED config.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39129
2013-12-17 22:14:12 +00:00
Gabor Juhos
c72313fd98 ar71xx: implement switch fix for WD My Net N750
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.

This fix implements just that.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39128
2013-12-17 22:14:11 +00:00
Gabor Juhos
8b712436f3 ar71xx: implement callback in mdio reset
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39127
2013-12-17 22:14:10 +00:00
Gabor Juhos
ba860e4c3a ar71xx: make ag71xx_mdio_platform_data visible
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39126
2013-12-17 22:14:07 +00:00
Gabor Juhos
31de995025 ar71xx: ag71xx: compute the RX buffer size from the maximum frame size
Currently, the AG71XX_RX_PKT_SIZE value limits the received
frame size to 1514/1516 bytes with/without a VLAN header
respectively. However the hardware limit is controlled by
the value the AG71XX_REG_MAC_MFL register which contains
the value of the max_frame_len field.

Compute the RX buffer size from the max_frame_len field
to get rid of the 1514/1516 byte limitation. Also remove
the unused AG71XX_RX_PKT_SIZE definition.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39121
2013-12-17 16:27:46 +00:00
Gabor Juhos
b35e0da0f4 ar71xx: ag71xx: store RX buffer size in the ag71xx struct
This allows to change the value dynamically.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39120
2013-12-17 16:27:44 +00:00
Gabor Juhos
6072e777e9 ar71xx: ag71xx: store maximum frame length in the ag71xx struct
This will allow to use different values for the
different SoCs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39117
2013-12-17 15:18:16 +00:00
Gabor Juhos
ea89cc9250 ar71xx: ag71xx: use mdio bus name in ar7240_probe messages
The ar7240_probe function uses the network device name
in the kernel log messages, however the name is not yet
initialized when the ar7240_probe function is called.
Use the mdio bus name in the messages to avoid ugly
log lines like the following one:

  eth%d: Found an AR7240/AR9330 built-in switch

Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39116
2013-12-17 15:12:52 +00:00
Gabor Juhos
0d7a6748e1 ag71xx: ag71xx: use device name for debugfs entry
The ag71xx debugfs code uses the network device name
for the device specific debugfs directory. Since r38689
'ar71xx: ag71xx: fix a race involving netdev registration'
the debugfs initialization happens before the ethernet
device gets registered and the network device name contains
'eth%d' at this point. If the board setup code registers
multiple ag71xx devices, the debugfs code tries to create
the device specific dir with the same name which causes
an error like this:

  eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
  ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
  ag71xx: probe of ag71xx.0 failed with error -12

Use the device name for the debugfs directory to avoid the
collisions. Also add an error message and change the return
code if the debugfs_create_dir call fails.

Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39115
2013-12-17 15:12:50 +00:00
Gabor Juhos
5237a50089 ar71xx: add initial support for the Mikrotik RB911G/RB912UAG boards
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39102
2013-12-16 18:08:51 +00:00
Gabor Juhos
8461ffccc1 ar71xx: add NAND driver for the Mikrotik RB91x boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39097
2013-12-16 12:57:24 +00:00
Gabor Juhos
d7a0184446 ar71xx: rb2011: use board name from the hardware config
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39096
2013-12-16 12:41:48 +00:00
Gabor Juhos
26ca95fefa ar71xx: rb2011: simplify setup code
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39095
2013-12-16 10:28:42 +00:00
Gabor Juhos
59b6cf1e70 ar71xx: rb2011: use the new RouterBOOT helpers
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39094
2013-12-16 10:28:41 +00:00
Gabor Juhos
627651dfca ar71xx: rb95x: use the rb_get_wlan_data helper
Also remove unused RB_* defines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39092
2013-12-16 10:11:02 +00:00
Gabor Juhos
16565ec94b ar71xx: add some RouterBOOT specific helper functions
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39091
2013-12-16 10:11:01 +00:00
Gabor Juhos
c92a4a427e ar71xx: refresh m25p80 patches
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39089
2013-12-16 10:10:58 +00:00
Gabor Juhos
728c2c6cff ar71xx: rb95x: nuke rb95x_gpio_init
Set up the chipselect GPIO directly in rb95x_nand_init
instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39087
2013-12-16 08:17:40 +00:00
Gabor Juhos
f1eabfb23b kernel: remove obsolete yaffs options from target configs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39085
2013-12-16 07:51:21 +00:00
Gabor Juhos
6928b4121f ar71xx/mikrotik: disable unused MTD options
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39080
2013-12-16 07:39:22 +00:00
Gabor Juhos
d208d3fe1a ar71xx: add dummy rle_decode function if CONFIG_RLE_DECOMPRESS is not set
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39079
2013-12-16 07:37:31 +00:00
Gabor Juhos
7038fd9c52 ar71xx: add userspace support for WD My Net N750
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: remove the image generation part until the ethernet
         switch issue is resolved]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39078
2013-12-16 07:16:43 +00:00
Gabor Juhos
3dc1cbb167 ar71xx: add kernel support for WD My Net N750
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39077
2013-12-16 07:16:42 +00:00
Gabor Juhos
749c44b24d ar71xx: build image for the TP-Link TL-WA901ND v3 board
Based-on: http://patchwork.openwrt.org/patch/4507/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39075
2013-12-15 21:34:20 +00:00
Gabor Juhos
3af206abb3 ar71xx: add user-space support for the TP-Link TL-WA901ND v3 board
Based-on: http://patchwork.openwrt.org/patch/4508/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39074
2013-12-15 21:34:19 +00:00
Gabor Juhos
fd393c0b05 ar71xx: add kernel support for the TL-WA901ND v3 board
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39073
2013-12-15 21:34:18 +00:00
Gabor Juhos
9ce06f2ac8 ar71xx: move TL-WA801ND v2 setup code
The TL-WA801ND v2 board has only one LAN port which makes
it more similar to the TL-WR[78]50RE devices. Move the
board setup code into the mach-tl-wax50re.c file.

Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39072
2013-12-15 21:34:17 +00:00
Gabor Juhos
40f081ad08 ar71xx: refactor TL-WAx50RE setup code
This way it is a bit easier to add other TP-LINK devices based on the
Atheros AP123 reference board with one LAN port.

Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39071
2013-12-15 21:34:15 +00:00
Gabor Juhos
e2fc4dc4e7 ar71xx: build firmware image for the TL-WA801ND v2
Patch to add the profile for the TP-LINK WA801ND v2

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4502/
[juhosg: change subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39065
2013-12-15 20:39:12 +00:00
Gabor Juhos
3e994a81d4 ar71xx: add user space support for the TL-WA801ND v2
Patch to add the user space support for the TL-WA801ND v2

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4501/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39064
2013-12-15 20:39:11 +00:00
Gabor Juhos
e3e559fd52 ar71xx: add kernel support for the TL-WA801ND v2 board
Patch to add kernel support for the TP-LINK WA801ND v2

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4500/
[juhosg:
  - the TL-WA801ND v2 does not have a sliding switch, it uses a push button
    for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that,
  - rename kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39063
2013-12-15 20:39:10 +00:00
Hauke Mehrtens
952db22551 kernel: update kernel 3.10 to 3.10.24
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 39059
2013-12-15 19:16:30 +00:00
Felix Fietkau
7a260c3620 ath9k: merge initval and tx gain table updates, calibration fixes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39001
2013-12-08 14:48:30 +00:00
Gabor Juhos
f1ef0b92be kernel: update 3.10 to 3.10.21
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38972
2013-12-01 09:59:53 +00:00
Luka Perkov
f51d78f4f2 ar71xx: merge board specific patches into one
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 38971
2013-11-30 19:48:05 +00:00
Gabor Juhos
9c4c620a11 kernel: refresh kernel configs with kconfig.pl
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38970
2013-11-30 18:31:10 +00:00
Gabor Juhos
e629881e2d ar71xx: update Userspace support for the WA850/WA750
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38969
2013-11-30 18:31:08 +00:00
Gabor Juhos
6688857d39 ar71xx: Update profile for the wa750/wa850 to include rssileds by default
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38968
2013-11-30 18:31:06 +00:00
Gabor Juhos
6ad568902e ar71xx: use cybertan_check_image for image verification on the WRT160NL
That function provides a slightly improved sanity check than the
currently used solution.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38967
2013-11-30 18:31:04 +00:00
Gabor Juhos
1fa75d430a ar71xx: sysupgrade for My Net Wi-Fi Range Extender
This patch enables the convenient sysupgrade feature for
WD's Wi-Fi Range Extender.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4341/
[juhosg:
  - rename 'mynet_rext_check_image' function to 'cybertan_check_image'
    and move that into platform.sh,
  - remove the the model specific 'platform_do_upgrade_mynet_rext' function,
  - drop the mynet-rext.sh script,
  - remove the image/Makefile change,
  - update commit message]
[christian:
  - check all 8 bytes of the firmware/device magic]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38966
2013-11-30 18:31:03 +00:00
Gabor Juhos
3674062469 ar71xx: image: unify CyberTAN macros
Make the Image/Build/CyberTAN macro more generic,
and use simple wrappers for the GZIP/LZMA variants.
This simplifies the Makefile a bit, and allows to
build sysupgrade images for the devices which are
using LZMA compressed uImages.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38965
2013-11-30 18:31:01 +00:00
Gabor Juhos
cb67115b4c ar71xx: image: fix CyberTAN sysupgrade images
In the current sysupgrade images, the CRC32 value of
the TRX header covers the whole rootfs data. Due to
this, the CRC value should be changed during sysupgrade
otherwise the bootloader refuses to load the image on
the next boot.

Change the image generation to create sysupgrade images
where the CRC32 value covers the kernel data only. This
allows to skip the 'fixtrx' step during sysupgrade on
the target.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38964
2013-11-30 18:30:59 +00:00
Gabor Juhos
a6ecce827a ar71xx: build image for the TL-WR1043ND v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38958
2013-11-29 20:51:16 +00:00
Gabor Juhos
7db7757bf2 ar71xx: add user-space support for the TL-WR1043ND v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38956
2013-11-29 20:51:13 +00:00
Gabor Juhos
bc2d7b8193 ar71xx: add kernel support for the TL-WR1043ND v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38955
2013-11-29 20:51:12 +00:00
Gabor Juhos
fd892350c2 ar71xx: add profile and build image for the Sitecom WLR-8100
- partitions on factory fw are a bit strange
  - unknown contained some strings in factory
  - unknown2 contains some atheros (2nd art ?)

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4149/
[juhosg: edit commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38954
2013-11-29 20:18:50 +00:00
Gabor Juhos
a0ad2a0f86 ar71xx: fix switch port map for the Sitecom WLR-8100
There was no way to determine a working config, because
the switch (ar8337) was not working previously.

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4470/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38953
2013-11-29 20:18:49 +00:00
Gabor Juhos
c1fb0e5e39 ar71xx: rssi leds for My Net WiFi Range Extender
The device has three extra LEDs which indicate the quality
of the wireless link. Thanks to rssileds, this feature now
works out of the box.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4462/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38950
2013-11-29 20:18:45 +00:00
Gabor Juhos
981e3b354a ar71xx: improve support for the My Net Wi-Fi Range Extender device
This patch improves support for the device considerably.

1. The wifi didn't work in the initial release. This was because
the WMAC of the AR9340 is not connected to the antennas.
(However, it can pick up wifi signals, if they are strong enough!)
Instead there's a dedicated AR9300 chip on the same board, which
works.

2. Ethernet throughput is improved. iperf shows that the hardware
can sustain more than 200Mbit/s and no longer drops any packages
when the link is under load.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4461/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38949
2013-11-29 20:18:44 +00:00
Gabor Juhos
1167f92ac6 ag71xx: add F1E specific feature bit definitions to AR934X register file
The F1E Phy (AR8035?) requires additional bits to be
set in order to provide a fast and reliable connection
over gigabit links.

When enabled, the link doesn't suffer anymore from a small
package loss under load and the performance is improved
quite a bit as well. (203 mbit/s vs 112 mbit/s, iperf tcp).

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4460/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38948
2013-11-29 20:18:43 +00:00
Gabor Juhos
cad5257732 ar71xx: user space support update tl-wr842n_v2 add default led support
Small update to uci_defaults/01_leds, to support the usb led

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38947
2013-11-29 20:18:42 +00:00
Gabor Juhos
af4873e41c ar71xx: Kernel support update tl-wr842n_v2 added missing usb led
Just a small oversight my part, added the support for the USB led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4425/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38946
2013-11-29 20:18:40 +00:00
Gabor Juhos
1f34789015 ar71xx: add profile for the WR842N/ND v2
Patch to add the profile for the TP-LINK WR842N/ND v2
Small update, because of a change in the Makefile.

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4382/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38815
2013-11-15 10:11:25 +00:00
Gabor Juhos
ed036155ee ar71xx: add user space support for the TL-WR842N/ND v2
Patch to add the user space support for the TL-WR842N/ND v2

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4354/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38814
2013-11-15 10:11:24 +00:00
Gabor Juhos
625cf61c5b ar71xx: Add kernel support for the WR842N/ND v2
Patch to add kernel support for the TP-LINK WR842N/ND v2

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4352/
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38813
2013-11-15 10:11:20 +00:00
Gabor Juhos
67eded254a ar71xx: wndr4300: set official mac addresses
Get the factory assigned mac addresses stored in the caldata
partition and asign them to lan and wan interfaces. Also put
the correct mac addresses into the WiFi eeprom files to ensure
that the ath9k driver will use the correct ones.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Patchwork: http://patchwork.openwrt.org/patch/4350/
[juhosg:
  - move WiFi MAC address setup to the firmware hotplug file,
  - use the official MAC address for the 2.4GHz as well,
  - remove uci-defaults.sh modifications,
  - update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38812
2013-11-15 08:21:59 +00:00
Felix Fietkau
ff17114ba1 ar71xx: Unifi AP Pro sysupgrade patch
The current implementation of mtd will not append the backup
file created by sysupgrade to the correct partition, as mtd will append
the data to first jffs2 partition it finds. As the kernel is also
stored on a jffs2 partition (which resides before the overlay
partition), the data will be appended to this partition.

To fix this problem, a new option

-s <number>             skip the first n bytes when appending data to the jffs2 partiton, defaults to "0"

is added to mtd.

Signed-off-by: Peter Wagner <tripolar@gmx.at>

SVN-Revision: 38807
2013-11-14 19:38:54 +00:00
Felix Fietkau
f38e6c782c ar71xx: use the new padjffs2 padding on Ubiquiti UAP-PRO to make the boot loader stop searching after the kernel partition
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 38805
2013-11-14 19:04:48 +00:00
Gabor Juhos
25756c61bc ar71xx: Use KEY_RESTART key code for the reset button on WD My Net N600 boards
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38720
2013-11-11 08:10:02 +00:00
Gabor Juhos
3d341e8ca5 ar71xx: add profile and build image for the TL-WA750RE TL-WA850RE range extender
Patch to add profile and build image for the tplink TL-WA750RE/WA850RE board

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38719
2013-11-11 08:04:48 +00:00
Gabor Juhos
d4cc7aac4b ar71xx: add user space support for the TL-WA750RE/WA850RE Range extender
Patch to add user space support for the TL-WA750RE/WA850RE range extender

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38718
2013-11-11 08:04:47 +00:00
Gabor Juhos
79163c8919 ar71xx: Add kernel support for the TP-Link WA750RE / WA850RE range extender
Patch to add kernel support for the TP-LINK WA750RE and the WA850RE
range extender

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38717
2013-11-11 08:04:46 +00:00
Gabor Juhos
ec09569b17 ar71xx: ag71xx: fix ag71xx_probe error path
Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38716
2013-11-11 07:47:00 +00:00
Gabor Juhos
7bd3a7bc7b ar71xx: ag71xx: fix a race involving netdev registration
In particular, phy_connect before register_netdev. This is because
register_netdev runs the netdev notifiers, which can race with the rest of
the initialization in ag71xx_probe. In my case this manifested in two ways:

1) If ag71xx is compiled as a module and inserted after netifd has started,
   netifd is notified by register_netdev before the call to
   ag71xx_phy_connect. netifd tries to bring the interface up, which calls
   ag71xx_open, which in turn enters ag71xx_phy_start. This keys off
   ag->phy_dev (which is still NULL) and thinks this is a fixed-link board,
   and enters ag71xx_link_adjust. This looks at ag->speed which is not yet
   initialized and hits the BUG() in the switch (ag->speed) in
   ag71xx_link_adjust.

   This is the wrong code path for ag71xx_phy_start - my board has PHYs that
   need to be brought up with phy_start. Doing ag71xx_phy_connect before
   register_netdev ensures that ag->phy_dev is non-NULL before
   ag71xx_phy_start is ever called.

2) When ag71xx is built into the kernel, and netconsole is enabled, there
   is a gap in the initial burst of replayed printks right after the netdev
   comes up. My assumption is that netconsole is also triggered by a netdev
   notifier, and part of this printk burst happens before the call into
   ag71xx_phy_connect, so part of the burst is lost while the PHY comes up.
   This patch fixes the gap - all the printks before eth0 comes up are bursted
   in full when netconsole initializes.

ag71xx_phy_connect_xxx no longer runs with a registered netdev, so the
logging has been adjusted accordingly to avoid "unregistered net_device" or
"eth%d" messages in dmesg.

Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38689
2013-11-08 08:17:54 +00:00
Gabor Juhos
f02c8802e3 ar71xx: build image for the WD My Net Wi-Fi Range Extender
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg:
  - remove the Image/Build/CyberTANLZMA/loader macro, it is not used
  - move the MYNETREXT SingleProfile definition to the correct place]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38688
2013-11-07 22:31:54 +00:00
Gabor Juhos
ddcce63c78 ar71xx: add user-space support for the WD My Net Wi-Fi Range Extender
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38687
2013-11-07 22:31:53 +00:00
Gabor Juhos
ece1323ed4 ar71xx: add kernel support for the My Net Wi-Fi Range Extender device
This patch adds a new device definition for a
Western Digital device. The hardware seems to
be based on Qualcomm Atheros DB120 design.

Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38686
2013-11-07 22:31:52 +00:00
Gabor Juhos
18d08da07d ar71xx: image: add EOF marker to the WNDR4300 UBI image
Append EOF markers to the END of the UBI image
file. This forces the kernel to erase all blocks
after the marker even if those blocks are not
empty.

Additionally, the resulting image can be flashed
from the original web UI now, so use '-factory'
suffix for that.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38683
2013-11-07 19:53:02 +00:00
Gabor Juhos
04fdff9dc0 ar71x: image: don't use the wndr3700 utility
Pass the uImage magic value directly to mkimage instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38662
2013-11-06 10:16:39 +00:00
Gabor Juhos
0c740a80fd ar71xx: image: fix WNDR4300 initramfs image generation
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38659
2013-11-05 18:41:20 +00:00
Gabor Juhos
c98db0707c ar71xx: image: allow to use optional parameters for MkuImageLzma/initramfs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38658
2013-11-05 18:41:18 +00:00
Gabor Juhos
08e0613275 ar71xx: generate recovery image for WNDR4300
Extended the Makefile to generate a working factory reset image
for Netgear WNDR4300. The image uses UBI with two volumes squashfs
(rootfs) and JFFS2 (rootfs_data). In order to make stock U-Boot
happy, a fake rootfs image is placed into the last erase block
of the kernel partition.

Signed-off-by: Stefan Agner <stefan@agner.ch>
[juhosg:
  - restore the NetgearNAND/initramfs macro,
  - remove unused {Squash,Ubi}fsTemplate macros,
  - remove board specific mtd options from CONFIG_CMDLINE, append the
    board specific ubi.mtd parameter to the kernel command line instead,
  - increase kernel partition size to 2MiB,
  - use board specific ini file for ubinize,
  - put jffs2 eof mark into the rootfs_data ubi volume,
  - use KDIR_TMP for temporary images,
  - use the squashfs-raw image,
  - increase kernel partition size to 2MiB,
  - use a local ubinize macro,
  - fix macro parameter comments,
  - put the fake rootfs into the last erase block of the kernel
    partition,
  - move Image/Build/NetgearNAND/buildkernel macro before
    define Image/Build/NetgearNAND,
  - don't use the wndr3700 utility, use '-M' parameter of mkimage to set
    the uImage magic,
  - use '-recovery' suffix for the generated image, it is only usable via
    the fw_recovery function of the bootloader,
  - update commit log]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38655
2013-11-05 16:31:14 +00:00
Gabor Juhos
35656042f1 kernel: update 3.10 to 3.10.18
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38652
2013-11-05 08:25:45 +00:00
Gabor Juhos
d5555de5b0 ar71xx: move WNDR4300 profile to the nand subtarget
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38647
2013-11-04 18:37:09 +00:00
Gabor Juhos
3eb676240f ar71xx: Add new subtarget nand for WNDR4300
Add new subtarget nand with UBI/UBIFS including GLUEBI and squashfs.
This target will be used for NAND based router which make use of
UBI (and maybe UBIFS later on) in order to provide proper NAND
support.

Signed-off-by: Stefan Agner <stefan@agner.ch>
[juhosg:
  - tweak target.mk:
     change BOARDNAME variable,
     improve Target/Description,
     remove targz and ubifs from FEATURES and add broken flag,
  - optimize kernel configuration:
     disable ubifs, it is not used yet,
     disable unused MTD options,
     disable SPI support
     disable unused network drivers,
     tune kernel command line,
  - remove image/ubinize.cfg, it will be in a follow-up patch
  - move profile modifications into a separate patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38646
2013-11-04 18:37:08 +00:00
Gabor Juhos
496d3e1149 ar71xx: remove yaffs from the generic rootfstype list
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38645
2013-11-04 18:37:07 +00:00
Gabor Juhos
ccf7320205 ar71xx: image: dd root.* images in fs specific macros
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38644
2013-11-04 18:37:06 +00:00
Gabor Juhos
45d26941b4 ar71xx: image: only define profiles for the generic subtarget
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38636
2013-11-01 18:33:24 +00:00
Gabor Juhos
f0a877e5eb ar71xx: image: add IMAGE_PROFILE variable
Ensures that the 'Default' images are generated
even if the subtarget has no profiles.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38635
2013-11-01 18:33:22 +00:00
Gabor Juhos
b2bc45d21e ar71xx: always enable hw ecc support for the ar934x-nfc module
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38634
2013-11-01 18:33:18 +00:00
Hauke Mehrtens
0e655122c6 kernel: add missing config options
The buildbots found some new missing config options.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38633
2013-11-01 08:49:35 +00:00
Gabor Juhos
715f16806f ar71xx: move subtarget specific features to target.mk
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38600
2013-10-30 06:54:59 +00:00
Gabor Juhos
5a08328197 ar71xx: don't build uImages for the mikrotik subtarget
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38598
2013-10-30 06:54:55 +00:00
Gabor Juhos
6357738509 ar71xx: disable non Mikrotik boards in the mikrotik subtarget
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38597
2013-10-30 06:54:54 +00:00
Gabor Juhos
228c3484c3 ar71xx: fix Kconfig symbol selection for RB95x/RB2011
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38596
2013-10-30 06:54:53 +00:00
Gabor Juhos
64ea60d210 ar71xx: move CONFIG_MTD_NAND_AR934X_HW_ECC option to subtarget config
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38595
2013-10-30 06:51:02 +00:00
Gabor Juhos
47b7ce5ec2 ar71xx: add profile and build image for the BXU2000n-2 A1 board
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
  - remove MultiProfile, it makes no sense for a single board
  - move SingleProfile call and the mtdlayout to a different
    location keep things sorted (well, almost)]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38593
2013-10-30 06:50:59 +00:00
Gabor Juhos
003a801dd9 ar71xx: add user-space support for the BXU2000n-2 A1 board
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38592
2013-10-30 06:50:58 +00:00
Gabor Juhos
ef8306cfd2 ar71xx: add kernel support for BHU Networks BXU2000n-2 A1 board
BXU2000n-2 A1 is a BHU Networks WLAN board, use ar9341 chip.

Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
  - rename and refresh kernel patch,
  - fix some checkpatch warnings and adjust whitespaces in
    mach-bhu-bxu2000n2-a.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38591
2013-10-30 06:50:57 +00:00
Gabor Juhos
acd4ea62e7 ar71xx: add user space support for the Sitecom WLR-8100 wireless router
Patchwork: http://patchwork.openwrt.org/patch/4148/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38590
2013-10-30 06:50:55 +00:00
Gabor Juhos
22b5040c64 ar71xx: add kernel support for the Sitecom WLR-8100 wireless router
- unsure about copyright message
  - based on AP136-010

Patchwork: http://patchwork.openwrt.org/patch/4147/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38589
2013-10-30 06:50:54 +00:00
Gabor Juhos
f6638a8994 ar71xx: add profile and build image for the Dragino2 board
Patchwork: http://patchwork.openwrt.org/patch/4234/
Signed-off-by: Pau Escrich <p4u@dabax.net>
[juhosg: remove kernel+rootfs partition and use uimage split instead]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38588
2013-10-30 06:50:53 +00:00
Gabor Juhos
7074bb286d ar71xx: add kernel support for DRAGINO2
This patch adds support for DRAGINO2 board (used by
Meshpotato v2). Most of the files included can be
found in the official svn repository provided by the
company [1]. I have just adapt it to the last OpenWrt
trunk revision (Fri Oct 4 10:49:47 2013).

 1. http://svn.dragino.com/dragino2

Patchwork: http://patchwork.openwrt.org/patch/4234/
Signed-off-by: Pau Escrich <p4u@dabax.net>
[juhosg:
 - rename and refresh kernel patch,
 - fix checkpatch warnings in  mach-dragino2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38587
2013-10-30 06:50:52 +00:00
Gabor Juhos
9e01011b5c ar71xx: rename 'nand' subtarget to 'mikrotik'
It is for Mikrotik devices only, rename the subtarget
to reflect that. Also fix the wget2nand script to use
the new image names.

Based on the patch by Stefan Agner:
http://patchwork.openwrt.org/patch/4123/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38509
2013-10-23 15:43:26 +00:00
Gabor Juhos
757a6fdef9 ar71xx: change title and description for NAND subtarget
The nand subtarget supports Mikrotik boards only. Change
the title and the description to reflect that.

Based on the patch by Stefan Agner:
http://patchwork.openwrt.org/patch/4123/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38508
2013-10-23 15:43:19 +00:00
Gabor Juhos
a59934dbd0 ar71xx: remove 'Target/Description' from main Makefile
Ensure that menuconfig shows the correct help text for
subtargets.

Based on the patch by Stefan Agner:
http://patchwork.openwrt.org/patch/4123/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38507
2013-10-23 15:43:13 +00:00
Gabor Juhos
b6b06000eb kernel: update 3.10 to 3.10.17
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38506
2013-10-23 12:51:05 +00:00
Gabor Juhos
80a15fe8ad ar71xx: Fix sysupgrades for Allnet and OpenMesh devices
Both Allnet and OpenMesh sysupgrade uses fw_setenv from uboot-envtools to
change different settings in the uboot environment. uboot-envtools version
2013.01 introduced a filesystem lock "/var/lock/fw_printenv.lock" to guarantee
mutually exclusive access to the uboot environment. But the path /var doesn't
exist on the sysupgrade ramfs.

An upgrade on these devices fails since r36033 ("[package] uboot-envtools:
upgrade to version 2013.01.01") with following messages:

 Error opening lock file /var/lock/fw_printenv.lock
 failed to update U-Boot environment

Creating the "/var/lock" path before running fw_setenv is therefore a
requirement unless the locking functionality in fw_setenv is removed or
replaced with optional locking.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38483
2013-10-20 15:59:05 +00:00
Gabor Juhos
68e13de37d ar71xx: fix WLAN 5 GHz LED init on dir-825-c1
Fixes the 5 GHz LED.

The same function has no effect on the 2.4 GHz LED at all, so we might
as well remove it.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38482
2013-10-20 15:59:04 +00:00
Hauke Mehrtens
81e2f00367 kernel: update kernel to 3.10.15
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38384
2013-10-13 19:28:29 +00:00
Vasilis Tsiligiannis
aac26bfbca ar71xx: Fix sysupgrade when upgrading to images with small rootfs partition
Signed-off-by: Vasilis Tsiligiannis <acinonyx@openwrt.gr>

SVN-Revision: 38382
2013-10-13 18:39:09 +00:00
Imre Kaloz
5f272ca813 make the generated images actually flashable on the Unifi devices.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 38364
2013-10-11 15:41:42 +00:00
Gabor Juhos
7815af409a ar71xx: ar934x-nfc: disable subpage write when hardware ECC is used
It is not supported by the controller.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38234
2013-09-27 11:15:34 +00:00
Gabor Juhos
9c8a5ef115 kernel: update 3.10 to 3.10.13
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38228
2013-09-27 07:19:21 +00:00
Felix Fietkau
a30681dff0 build: unify mips target cflags
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 38210
2013-09-26 17:53:14 +00:00
Gabor Juhos
b71c7d8d3c ar71xx: use correct board id for TL-MR3040 v2
Fix the image building code so that the kernel correctly
distinguishes between hardware revisions.

Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38192
2013-09-25 18:42:14 +00:00
Gabor Juhos
164cd38b41 ar71xx: add user-space support for TL-MR3040 v2
Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38191
2013-09-25 18:42:11 +00:00
Gabor Juhos
f8aef84e49 ar71xx: improve kernel support for the TL-MR3040 v2
This patch adds support for the hardware slide switch on
the TL-MR3040 v2.

Signed-off-by: Mads Hansen <d@taba.se>
[juhosg: use EV_SW instead of EV_KEY]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38190
2013-09-25 18:42:10 +00:00
Gabor Juhos
0380904acb kernel/3.10: refresh all target patches
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38182
2013-09-25 17:13:24 +00:00
Gabor Juhos
904ffa32d8 ar71xx: image: simplify mynet_n600_mtdlayout
Remove the kernel and rootfs partitions. The Seama
parser can find those automatically:

  0x000000070000-0x000000ff0000 : "firmware"
  2 seama-fw partitions found on MTD device firmware
  0x000000070000-0x0000001b0000 : "kernel"
  0x0000001b0000-0x000000ff0000 : "rootfs"
  mtd: partition "rootfs" set to be root filesystem
  1 squashfs-split partitions found on MTD device rootfs
  0x000000360000-0x000000ff0000 : "rootfs_data"
  0x000000ff0000-0x000001000000 : "radiocfg"

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38155
2013-09-24 12:19:57 +00:00
Gabor Juhos
2f5694398d ar71xx: enable the Seama firmware parser
It will be used for the WD My Net N600 board.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38154
2013-09-24 12:19:54 +00:00
Gabor Juhos
2ea3cac075 ar71xx: update the Image/Build/WZRHP macro
- append the root squashfs directly after the kernel,
 - use the 64kraw/128kraw template instead of the 64k/128k,
 - ensure that the generated images have enough erase blocks
   for JFFS2 garbage collection,

Tested on WZR-HP-G300NH and WZR-600DHP boards.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38153
2013-09-24 09:36:26 +00:00
Gabor Juhos
d0ba5d1584 ar71xx: image: use a common macro for Buffalo WZRHP devices
The Image/Build/WZRHP64K and the Image/Build/WZRHP128K macros
are similar. Move the common stuff into the Image/Build/WZRHP
macro and update the orignal macros to use that.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38152
2013-09-24 09:36:25 +00:00
Gabor Juhos
370405bfd0 ar71xx: image: update Image/Build/CameoAP94 macro
- append the root squashfs directly after the kernel,
 - use the 64kraw template instead of the 64k,
 - ensure that the generated images have enough erase blocks
   for JFFS2 garbage collection,

Tested on a TEW-673GRU board.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38151
2013-09-24 08:14:44 +00:00
Gabor Juhos
167c4b5fa7 ar71xx: image: use a common macro for Cameo AP94 based devices
The Image/Build/DIR825B1 and the Image/Build/DLRTDEV macros
are identical. Merge those into a new Image/Build/CameoAP94
macro, and update the device profiles to use the new macro.
Also rename the dir825b1_* mtdlayout macros to cameo_ap94_*.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38150
2013-09-24 08:14:43 +00:00
Gabor Juhos
fe525cd2c0 ar71xx: image: use the board name for temporary mtdpart files
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38149
2013-09-24 06:13:14 +00:00
Gabor Juhos
5da3667d79 ar71xx: update the Image/Build/UBNT2 macro
- append the root squashfs directly after the kernel,
 - use the 64kraw template instead of the 64k,
 - ensure that the generated images have enough erase blocks
   for JFFS2 garbage collection,

Tested on a WispStation M5 board.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38148
2013-09-24 05:58:34 +00:00
Gabor Juhos
18141628dc ar71xx: build intramfs images for the Ubiquiti XM boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38147
2013-09-24 05:58:32 +00:00
Gabor Juhos
4fc427e211 ar71xx: image: use a common macro for UBNTXM/UBNTDEV
The firmware generation part is the same for both
macros. Move that into a separate macro and use the
new macro for Image/Build/UB{NTXM,DEV}.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38146
2013-09-24 05:58:31 +00:00
Gabor Juhos
0b09a89340 ar71xx: image: update Image/Build/WHRHPG300N macro
- append the root squashfs directly after the kernel,
 - use the 64kraw template instead of the 64k
 - ensure that the generated images have enough erase blocks
   for JFFS2 garbage collection,

Tested on the WHR-G301N board only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38141
2013-09-23 19:49:27 +00:00
Gabor Juhos
0264fed9bd ar71xx: image use the 64kraw template for the TEW-732BR board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38140
2013-09-23 12:54:05 +00:00
Gabor Juhos
7c8c366a14 ar71xx: image: update Build/Image/Planex macro
- remove the 'kernel' and 'rootfs' partitions from the mtd layout,
 - move the .okli image into the uImage,
 - append the root squashfs directly after the kernel,
 - use the 64kraw template instead of the 64k
 - ensure that the generated images have enough erase blocks
   for JFFS2 garbage collection,

Tested on the MZK-W300NH board only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38139
2013-09-23 12:14:20 +00:00
Gabor Juhos
58e3d03ae0 ar71xx: image: allow to build initramfs for Planex devices
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38138
2013-09-23 12:14:19 +00:00
Gabor Juhos
0ff5dc2f38 ar71xx: image: build Planex kernels in a separate step
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38137
2013-09-23 12:14:18 +00:00
Gabor Juhos
cdda5b041f ar71xx: add profile and build image for the TEW-732BR board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38133
2013-09-23 09:49:04 +00:00
Gabor Juhos
525fcc6e11 ar71xx: add user-space support for the TEW-732BR board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38132
2013-09-23 09:49:02 +00:00
Gabor Juhos
8b920136a0 ar71xx: add kernel support for the TEW-732BR board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38131
2013-09-23 09:49:01 +00:00
Gabor Juhos
3f5fae5e1a ar71xx: image: update the Image/Build/CameoHornet macro
- append the root squashfs directly to the kernel,
 - use the 64kraw-nojffs template instead of sqashfs-only
 - ensure that the generated images have enough erase blocks
   for JFFS2 garbage collection,

Tested on a TEW-712BR devices only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38130
2013-09-23 09:22:50 +00:00
Gabor Juhos
4dd84248d2 ar71xx: update the Image/Build/Cameo macro
- append the root squashfs directly to the kernel,
 - use the 64kraw/64kraw-nojffs template instead of 64k/squashfs-only,
 - ensure, that the signature is placed at the correct offset in
   the *-factory images,
 - ensure that the generated images have enough erase blocks
   for JFFS2 garbage collection,

Tested on DIR-600-A1 and TEW-632BR devices only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38129
2013-09-23 09:01:06 +00:00
Gabor Juhos
3131a1c11a ar71xx: image: add new macros for AP99 based Cameo devices
The MTD layout of the AP99 based devices is different.
Add new macros to reflect that and use the new macros
for the DIR-615-E4 board.

This prevents overwriting of the 'mac' partition which
contain vital informations. The disadvantage of the change
is that the usable space is reduced by 192KiB. Blame the
vendors for the unfriendly partition layout.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38128
2013-09-23 08:24:10 +00:00
Gabor Juhos
ac2cd03c73 ar71xx: image: rename the Cameo macros
Use the reference board name in the macro
instead of the SoC number.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38127
2013-09-23 08:24:05 +00:00
Gabor Juhos
dd171f7d14 ar71xx: image: add optional JFFS2 padding support to the CatFiles macro
Also remove the similar code from the Netgear
profile and use the new feature instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38126
2013-09-22 20:14:23 +00:00
Gabor Juhos
d3c75d79cd ar71xx: image: remove too big files in the CatFiles macro
Also improve the warning message.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38125
2013-09-22 20:14:22 +00:00
Gabor Juhos
3b00bf1a68 ar71xx: simplify wndr3700 image generation
- remove the kernel and rootfs partitions from the mtd layout,
   the kernel creates those automatically,
 - remove estimation step, it is not needed anymore
 - put the root squashfs directly after the kernel
 - use the 64kraw template

With the default configuration, this allows to use more space for
rootfs_data with 64KiB. Tested on WNDR3700 v1 only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38120
2013-09-22 11:45:09 +00:00
Gabor Juhos
10a0f65be0 ar71xx: use the separate rootfs and uImage parsers
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38119
2013-09-22 11:45:08 +00:00
Gabor Juhos
2434b9e413 ar71xx: sync kernel config
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38118
2013-09-22 11:45:06 +00:00
Gabor Juhos
ea0ff700e8 ar71xx: image: add mtdpartsize macro
The new macro will be used to determine the firmware
partition size from an MTD layout.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38117
2013-09-22 09:11:25 +00:00
Gabor Juhos
48a3a30fec ar71xx: image: improve the rootfs_align macro
Improve the macro to return correct value for
all squashfs variant.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38116
2013-09-22 09:11:24 +00:00
Gabor Juhos
b77d4d8d19 ar71xx: image: improve the CatFiles macro
Make it possible to append the rootfs image directly
to the kernel.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38115
2013-09-22 09:11:22 +00:00