Commit graph

2524 commits

Author SHA1 Message Date
Felix Fietkau
6327386aff ar71xx: fix invalid pointer accesses caused by unaligned access hacks (#18455)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43560
2014-12-08 10:48:28 +00:00
John Crispin
3572657c5a ar71xx: dev-eth: replace mdelay calls
Similar to patch 2. Replace further mdelay calls.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 43540
2014-12-07 16:53:15 +00:00
John Crispin
59e7999a44 ag71xx: replace delay with sleep calls
I don't see that we're in an atomic context so there's no need to
busy-wait. Therefore replace the delay with sleep calls.
See also Documentation/timers/timers-howto.txt. It states:
"In general, use of mdelay is discouraged and code should
be refactored to allow for the use of msleep."

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 43539
2014-12-07 16:53:09 +00:00
John Crispin
4caa8d50ad ag71xx: replace fixed PHY reset wait time in ar7240sw_setup
Replace the fixed wait time of 1s with polling for BMCR_RESET
to be cleared on all PHYs.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 43538
2014-12-07 16:52:58 +00:00
John Crispin
610311436e ar71xx: Add build profile for the gl-inet 6416A and 6408A
Patch to add the buildprofile for the GL-Init-6408A-v1 and the GL-Inet-6416A-v1
Both devices are identical, only difference is one comes with 8MB flash and
the other with 16MB flash

Official website: http://www.gl-inet.com/w/?page_id=241&lang=en
Comprehensive list of specs: https://revspace.nl/GL-Inet

Signed-off-by: Martijn Zilverschoon <martijn@friedzombie.com>

SVN-Revision: 43462
2014-12-01 16:14:02 +00:00
Imre Kaloz
974f286261 add D-link DGL-5500 A1 support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43401
2014-11-27 14:27:34 +00:00
Imre Kaloz
7f6c05d97e fix the r6100's wan led name
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43393
2014-11-26 11:38:59 +00:00
John Crispin
47ab1cbf23 ar71xx: add support for TP-LINK CPE210/220/510/520
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 43385
2014-11-26 08:59:32 +00:00
Imre Kaloz
15f6f67d18 Netgear R6100 support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43382
2014-11-26 08:28:22 +00:00
Felix Fietkau
174d16e59f ar71xx: merge changes from 3.10 that were forgotten for 3.14
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43347
2014-11-23 16:27:19 +00:00
Felix Fietkau
25cb8318cd ar71xx: remove linux 3.10 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43344
2014-11-23 13:54:28 +00:00
Felix Fietkau
0179456212 ar71xx: switch to linux 3.14
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43343
2014-11-23 13:54:22 +00:00
John Crispin
f210f3811a ar71xx: Added support for D-link DHP-1565 rev. A1
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>

SVN-Revision: 43307
2014-11-19 09:20:47 +00:00
John Crispin
6af2109a64 ar71xx: fix switch configuration in Ubiquiti UAP Pro
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 43306
2014-11-19 09:20:18 +00:00
John Crispin
6fafcba63b ar71xx: Fix the sys LEDs on the EasyLink M150 and mini
Sets the system LED on the EasyLink M150 and mini to lower-case "easylink"

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 43271
2014-11-14 16:58:29 +00:00
John Crispin
b6f5713b3f ar71xx: adjust MR900 profile for the OpenMesh MR900v2 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43270
2014-11-14 16:55:32 +00:00
John Crispin
52c267e2f7 ar71xx: add sysupgrade support for OpenMesh MR900v2
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43267
2014-11-14 16:55:14 +00:00
John Crispin
104be9f803 ar71xx: add user-space support for OpenMesh MR900v2
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43266
2014-11-14 16:55:04 +00:00
John Crispin
bc333d5399 ar71xx: add kernel support for the OpenMesh MR900v2
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43265
2014-11-14 16:54:58 +00:00
John Crispin
305c1431e3 ar71xx: create profile and build image for the OpenMesh MR900 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43264
2014-11-14 16:54:50 +00:00
John Crispin
548822cd7a ar71xx: enable sysupgrade for the OpenMesh MR900
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43261
2014-11-14 16:54:28 +00:00
John Crispin
cfdaa8aefd ar71xx: add user-space support for the OpenMesh MR900 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43259
2014-11-14 16:54:15 +00:00
John Crispin
95544f33dd ar71xx: add kernel support for the OpenMesh MR900 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43258
2014-11-14 16:54:07 +00:00
Felix Fietkau
8acf9adf28 ar71xx: add missing WZR-450HP2 patch from r43026 for 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43175
2014-11-03 22:55:01 +00:00
John Crispin
2c72ffc154 ar71xx: add support for Netgear WNR2000v4
Signed-off-by: Michaël Burtin <mburtin@gmail.com>

SVN-Revision: 43173
2014-11-03 20:20:56 +00:00
Felix Fietkau
2eb6b059ba ar71xx: refresh 3.10 patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43051
2014-10-24 20:39:42 +00:00
Felix Fietkau
c288d2d6d9 kernel: makefiles: make use of new var KERNEL_PATCHVER
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16

Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>

SVN-Revision: 43047
2014-10-24 19:34:02 +00:00
Felix Fietkau
a1837135e0 ar71xx: add support for buffalo WZR-450HP2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43026
2014-10-22 11:02:18 +00:00
John Crispin
32acfefb6a ar71xx: unify usage of IMAGE_PROFILE instead of PROFILE.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 42992
2014-10-20 06:29:58 +00:00
John Crispin
182d63bc40 ar71xx: add comments for Image/BuildLoader{, Alone}.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 42990
2014-10-20 06:29:44 +00:00
Felix Fietkau
a7ee0142e7 ar71xx: disable irq on reboot to fix hang issues (fixes #17839)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42955
2014-10-18 19:25:30 +00:00
John Crispin
6e46fc8a38 wr1043nd-v2: Change .code of the wi-fi button to KEY_RFKILL
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.

Signed-off-by: Josef Gajdusek <atx@atx.name>

SVN-Revision: 42922
2014-10-14 19:01:21 +00:00
John Crispin
70def60b04 ar71xx: fix seama factory type image generation.
Currently JFFS2 end-of-filesystem marker 0xdeadc0de is included the
computation of image's MD5 checksum as part of the seama header.  But
OpenWrt will erase blocks including and after the marker thus
invalidating the checksum after the first boot.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 42915
2014-10-14 12:21:41 +00:00
John Crispin
24a0269b71 ar71xx: qihoo-c301: reset imageNtrynum after each successful boot.
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup.  OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry.  If such a region
is found, bootloader will try to increment imageNtrynum and boot it.

This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).

	root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
	00000000  9e f3 63 91 61 63 74 69  76 65 72 65 67 69 6f 6e  |..c.activeregion|
	00000010  3d 31 00 69 6d 61 67 65  31 73 74 61 74 75 73 3d  |=1.image1status=|
	00000020  30 00 69 6d 61 67 65 32  73 74 61 74 75 73 3d 30  |0.image2status=0|
	00000030  00 69 6d 61 67 65 32 74  72 79 6e 75 6d 3d 30 00  |.image2trynum=0.|
	00000040  69 6d 61 67 65 6d 61 78  74 72 79 3d 33 00 69 6d  |imagemaxtry=3.im|
	00000050  61 67 65 31 74 72 79 6e  75 6d 3d 30 00 00 00 00  |age1trynum=0....|
	00000060  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 42914
2014-10-14 12:21:36 +00:00
John Crispin
20940138ac scripts: fix wrong usage of '==' operator
[base-files] shell-scripting: fix wrong usage of '==' operator

normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.

this patch does not change the behavior/logic of the scripts.

Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>

SVN-Revision: 42911
2014-10-14 12:21:11 +00:00
John Crispin
99c238ff15 ar71xx: Fix LED definitions for the DRAGINO2 board
This patch fixes LED definitions for the DRAGINO2 board.

1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 42897
2014-10-14 10:33:07 +00:00
John Crispin
e77ae183a1 ar71xx: correctly detect hardware revision on TP-LINK Archer C5 and C7
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 42797
2014-10-06 04:53:34 +00:00
John Crispin
7f772910a1 ar71xx: fix syntax for TP-LINK TL-WR941N/ND / Rosewill RNX-N360RT detection
[ ] conditions should use = instead of == for string equality.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 42796
2014-10-06 04:53:25 +00:00
John Crispin
05777fb947 ar71xx: simplify TP-LINK model detection
All TP-LINK machine names begin with "TP-LINK", so there's no need to check for
more specific model names. This also allows adding new models like the Archer
series more easily.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 42795
2014-10-06 04:53:20 +00:00
John Crispin
73acd5050f ar71xx: add support for TP-LINK TL-WR847N v8 (clone of TL-WR841N/ND v8)
Signed-off-by: Jaehoon You <teslamint@gmail.com>

SVN-Revision: 42792
2014-10-06 04:52:57 +00:00
John Crispin
491e028e2d ar71xx: add LED defaults for the EnGenius ESR1750
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42786
2014-10-06 04:52:13 +00:00
John Crispin
e2c3c2280c ar71xx: fix reset button gpio for OM2P/OM2P-HS
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".

Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 42782
2014-10-06 04:51:51 +00:00
Felix Fietkau
61f960071d ar71xx: revert accidental kernel upgrade
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42687
2014-09-27 20:54:12 +00:00
Felix Fietkau
3e833dcf90 ar71xx: add wmac callback for reading soc revision on ar934x
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42685
2014-09-27 20:52:05 +00:00
Felix Fietkau
84d81d5844 ar71xx: refresh 3.14 kernel patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42684
2014-09-27 20:51:49 +00:00
John Crispin
7dbbdfb61f ar71xx: add qihoo 360 c301 router support
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.

This patch adds its initial support.

v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 42552
2014-09-15 10:19:38 +00:00
John Crispin
cb37fe5ca5 ar71xx: add board support for ubnt loco m xw
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 42549
2014-09-15 10:19:14 +00:00
John Crispin
2c4c6d135b ar71xx: refactor ubnt xw board setup
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 42548
2014-09-15 10:19:01 +00:00
Felix Fietkau
1961f8cdb7 ar71xx: ack completed tx descriptors only after the full frame has been completed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42457
2014-09-10 12:56:24 +00:00
Felix Fietkau
60b81acd60 ath79: dev-eth: Don't advertise 1gbit in link code word on ar9331
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable.  The existing code
however advertieses gigabit capability in the link status word.  If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link.  This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.

In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.

So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit.  This patch implements the
former solution.

Signed-off-by: Harald Welte <laforge@gnumonks.org>

SVN-Revision: 42432
2014-09-07 09:45:32 +00:00
Felix Fietkau
60eeadd0ba ar71xx: re-enable descriptor splitting on ar716x after the previous bugfixes (#13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42429
2014-09-06 17:51:48 +00:00
Felix Fietkau
2da2317fed ar71xx: fix off-by-one error in packet descriptor splitting (patch from #13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42428
2014-09-06 17:51:44 +00:00
Felix Fietkau
05dd36a980 ar71xx: on ar716x, split ethernet packets in 512 byte chunks instead of 256 (improves performance) (patch from #13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42427
2014-09-06 17:51:39 +00:00
Felix Fietkau
926f000b99 ar71xx: disable ethernet descriptor splitting for now, as it seems to cause tx hangs in some setups
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42333
2014-08-30 09:11:41 +00:00
Felix Fietkau
4ff324191f ar71xx: select m25p80 support instead of spi support where used by mach files (#17699)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42331
2014-08-29 21:10:39 +00:00
Felix Fietkau
2c680151e4 ar71xx: split packets into multiple descriptors on ar716x
This improves performance when doing concurrent rx/tx on a single
ethernet MAC, e.g. when routing between VLANs.

Fixes #13072

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42328
2014-08-29 19:42:08 +00:00
John Crispin
254b2670e1 ar71xx: add Support for RB2011UiAS-2HnD
SVN-Revision: 42317
2014-08-28 06:27:45 +00:00
John Crispin
67cf439237 ar71xx: use ETH_ALEN for consistency
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42280
2014-08-25 06:35:58 +00:00
John Crispin
79c04e1897 ar71xx: enable sysupgrade for the EnGenius ESR900
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42279
2014-08-25 06:35:54 +00:00
John Crispin
e5e1c03354 ar71xx: TL-WR1043N/ND v2: Fix MAC address of WMAC
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 42193
2014-08-18 13:10:00 +00:00
John Crispin
5d9b1e7ec1 ar71xx: build factory image for EnGenius ESR900 and ESR1750
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42189
2014-08-18 13:09:34 +00:00
John Crispin
2c67682192 ar71xx: Fix 2.4G WiFi LED of the OpenMesh MR600 board
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 42184
2014-08-18 13:09:14 +00:00
John Crispin
340f87a20f ar71xx: changed the EnGenius ESR900 mtdparts to match that of the ESR1750 since they have the same flash layout
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42177
2014-08-18 13:08:45 +00:00
Imre Kaloz
ecba34a3ee add support for the NC-LINK SMART-300
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 42130
2014-08-11 11:44:51 +00:00
Felix Fietkau
ad876993d3 ar71xx: port missing ath79 machine entry for wndr3700 v4 to 3.14
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42044
2014-08-07 18:59:15 +00:00
Felix Fietkau
e41a0cafff ar71xx: add linux 3.14 support
Signed-off-by: Zhao, Gang <gang.zhao.42@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42038
2014-08-07 12:40:53 +00:00
Steven Barth
e7be51a0fd ar71xx: Add support for the WNDR3800CH
Apparently this is a fairly common refurb unit of the 3800 series now,
with merely the recognition string changed in the boot loader.

Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>

SVN-Revision: 42023
2014-08-07 05:14:26 +00:00
Felix Fietkau
b855faecc0 ar71xx: update Carambola2 platform data
Change list:
 * Remove button info on GPIO12, there is no button there.
 * Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.

Tested building for carambola2 target.

Signed-off-by: Mantas Pucka <mantas@8devices.com>

SVN-Revision: 41993
2014-08-04 14:46:52 +00:00
John Crispin
e7ec79821a ar71xx: oolite: the buttons are not active_low
this caused factory resets when reboot was pressed

Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41932
2014-08-01 11:19:34 +00:00
John Crispin
6ce44430c9 ar71xx: add RTC feature flag to ar71xx/nand
without this the build for NBG6716 fails due to missing packages

https://dev.openwrt.org/ticket/17325

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41930
2014-08-01 10:32:55 +00:00
Imre Kaloz
dc628f2e08 add support for the archer c5
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41814
2014-07-23 12:47:25 +00:00
Imre Kaloz
039fe23f8e refresh patches
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41812
2014-07-23 11:46:42 +00:00
John Crispin
3bb8589787 ar71xx: fix LED configuration for HiWiFi-HC6361.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 41809
2014-07-23 07:46:07 +00:00
John Crispin
4f5081c911 ar71xx: fix WAN MAC setup on dir-825-c1
Changeset 38690 broke the WAN MAC setup. Here's the fix.

Signed-off-by: Sebastian Kemper <sebastian_ml <at> gmx.net>

SVN-Revision: 41795
2014-07-21 19:26:54 +00:00
John Crispin
6dd7875412 ar71xx: Register reset button on UBNT AirGW
The airGateway has a reset button connected to GPIO 12, so we should use it.

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>

SVN-Revision: 41794
2014-07-21 19:26:50 +00:00
John Crispin
a440524f85 ar71xx: Fix GL.iNet WLAN LED
LED script expects WLAN LED to be "gl-connect:red:wlan".

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 41793
2014-07-21 19:26:46 +00:00
John Crispin
eae9b2541a ar71xx: split wndr4300 and wndr3700v4 into 2 seperate mips machines
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41788
2014-07-21 18:41:52 +00:00
John Crispin
2b48ee80f9 kernel: refresh 3.10 patches
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41777
2014-07-20 17:31:15 +00:00
John Crispin
ba63338d3f kernel: update to 3.10.49 Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41776
2014-07-20 17:31:11 +00:00
John Crispin
34c9bc0596 ar71xx: create profile and build image for the OpenMesh OM5P board
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41775
2014-07-20 17:31:05 +00:00
John Crispin
f68665ac1d ar71xx: enable sysupgrade for the OpenMesh OM5P
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41772
2014-07-20 17:30:52 +00:00
John Crispin
e50abb5d53 ar71xx: add user-space support for the OpenMesh OM5P
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41770
2014-07-20 17:30:44 +00:00
John Crispin
f424994cbc ar71xx: add kernel support for the OpenMesh OM5P board
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41769
2014-07-20 17:30:32 +00:00
John Crispin
7388053ba3 ar71xx: add RB91x boards to uci-defaults 02_network
The default case in 02_network is inappropriate for the MikroTik RouterBOARD 91x boards because they do not have a WAN port, so don't bother setting the non-existent eth1 interface as the WAN port.

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>

SVN-Revision: 41767
2014-07-20 17:30:24 +00:00
John Crispin
d19530c693 ar71xx: Add UBNT airGateway support
This patch adds support for the Ubiquiti Networks airGateway.

Based in part on code posted by David Hutchison <dhutchison@bluemesh.net> on openwrt-devel:
  https://lists.openwrt.org/pipermail/openwrt-devel/2013-December/023035.html

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>

SVN-Revision: 41766
2014-07-20 17:30:17 +00:00
Imre Kaloz
7e2c4d5732 extract and fixup the board.bin on the archer
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41757
2014-07-19 13:20:14 +00:00
Gabor Juhos
2adff1734f ar71xx: add profile and build image for the EnGenius EAP300 v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41661
2014-07-14 21:30:30 +00:00
Gabor Juhos
54206fb0ce ar71xx: add user-space support for the EnGenius EAP300 v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41659
2014-07-14 21:30:28 +00:00
Gabor Juhos
aff3127956 ar71xx: add kernel support for the EnGenius EAP300 v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41658
2014-07-14 21:30:26 +00:00
Gabor Juhos
495aef39f4 ar71xx: add profile and build image for the Tube2H board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41652
2014-07-14 16:03:37 +00:00
Gabor Juhos
f27f2fec4f ar71xx: add user-space support for the Tube2H board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41650
2014-07-14 16:03:35 +00:00
Gabor Juhos
51c892053a ar71xx: add kernel support for the Tube2H board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41649
2014-07-14 16:03:34 +00:00
Gabor Juhos
907bd5345e ar71xx: fix ALFA NETWORK's name
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41643
2014-07-14 11:10:00 +00:00
Gabor Juhos
fec2596282 ar71xx: add profile and build image for the EnGenius ESR900
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5715/
[juhosg: change subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41642
2014-07-14 10:25:53 +00:00
Gabor Juhos
50c554a475 ar71xx: add user-space support for the EnGenius ESR900
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5716/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41641
2014-07-14 10:25:51 +00:00
Gabor Juhos
0bec90b830 ar71xx: add kernel support for the EnGenius ESR900
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5714/
[juhosg:
  - drop nvram.c modifications,
  - create a separate kernel patch,
  - use ath79_setup_qca955x_eth_cfg helper,
  - merge esr900_{010,common}_setup functions,
  - statically init AR8327 pad configurations,
  - use pr_err instead of printk]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41640
2014-07-14 10:25:51 +00:00
John Crispin
e503eeb465 ar71xx: add support for nanostation m xw
SVN-Revision: 41636
2014-07-14 07:38:43 +00:00
Gabor Juhos
26b39cc580 ar71xx: use ath79_setup_qca955x_eth_cfg helper for QCA955x based boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41627
2014-07-13 19:44:00 +00:00
Gabor Juhos
c4c25e741e ar71xx: add profile and build image for EnGenius ESR1750
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41626
2014-07-13 19:43:59 +00:00
Gabor Juhos
2d6542242a ar71xx: add user-space support for EnGenius ESR1750
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41625
2014-07-13 19:43:58 +00:00