While bumping 4.14, the kernel build failed due to missing CONFIG_KASAN
symbol. Move it to generic config instead of defining it for all arm64
and x86/64 targets.
It was only added in 4.0, so not needed in config-3.18.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The CPU sub type was set to a CPU version with FPU, but the FPU feature
was not activated before, so a soft float toolchain was created.
Activate also the FPU feature to create the correct toolchain.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates neon and VFPv4 support for this target. The CPU support
these feature so also use them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since BusyBox 1.25.0 dd command supports iflag=skip_bytes which allows
skipping requested amount of bytes without reducing blocksize. Thanks to
this we can leave default blocksize and let dd work more efficiently.
On Netgear R6250 "dd skip=58 iflag=skip_bytes" can be 5 times faster
than "dd bs=58 skip=1" when extracting TRX out of CHK.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's a device based on BCM5365P (0x5365 package 0x00). This SoC has
USB 1.1 controller but device has two USB 2.0 parts. They are handled by
PCI-based controllers: 1106:3038 UHCI and 1106:3104 EHCI.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This was broken in 7bab49fd ("lantiq: add compatible strings to dts
files"), causing for the dm200 garbled serial output during boot, and
likely other issues.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
[fix the compat string of the P2601HNFX as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
That patch fixes handling SPI messages with two writing transfers. It's
important when using e.g. by m25p80 driver which uses one transfer for
opcode and another one for data.
Thanks to that fix we can now drop m25p80 workaround patch. It means one
less hack and also a better flash writing performance as there is no
more data buf copying.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
A lot of 1U x86_64 servers have NVMe support, which is lower-power
and higher speed than SSD or CFast drives, etc. The drivers
required to make this work are trivial.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Remove a stray -Wp left in host_c_flags causing build failures for newer
4.14 versions.
Reported-by: Michael Marley <michael@michaelmarley.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Advantages:
- preserves existing partition layout on the sd-card.
Only the boot and rootfs partition will be overwritten.
Please note that sysupgrade will refuse to upgrade, if the existing
installation has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-sdcard.img.gz
will have to be written to the sdcard manually.
Please don't forget to backup your configuration in this case.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.
Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the compatible string for the various RPIs from
4.14 upstream.
Note: The 4.14 upstream does not include the compute modules.
If the CM* would just house the SoC, it could in theory use the
"raw" chip compatible string. However, these CM boards also come
with RAM and eMMC. So they have to have a proper comaptible.
For now, "raspberrypi,compute-module-{1|3}" will be good enough.
Note2: The original CM was renamed to CM1 when CM3 was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch converts all the raspberrypi images to utilize
the common metadata-based image verification.
Note: the CM1 and CM3 currently use the same "rpi-cm"
boardname.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit c312cef223 ("ar71xx: spi-rb4xx fix.") replaced the clk_enable() call
with clk_prepare_enable() to meet the common clock framework requirements.
However it did not change the clk_disable() call in the error patch which
thus leads to imbalance.
Fix the code by using the correct counterpart of clk_prepare_enable() in both
places.
Fixes: c312cef223 ("ar71xx: spi-rb4xx fix.")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The value DSL_ChipSetHWVersion is fetched from the dsl frontend
via the dsl_control service, but not really provided by the dsl
frontend firmware and for now always "UNKNOWN".
The lantiq support told us that this information wouldn't be
provided in the foreseeable future, so let's remove this
useless "UNKNOWN" information.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Use a more appropriate compatible string. Fix the wireless led GPIO and
add the default wireless trigger. Use the wireless LED for boot state
indication as well.
Remove the GPIO pinmux for pins not exposed on the board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link TL-MR3420 v5 are simple N300 router with
5-port FE switch and non-detachable antennas.
Its very similar to TP-Link TL-WR841N V13.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 8x LED, 2x button, power input switch
Flash instruction:
The only way to flash LEDE image in mr3420v5 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Move common tplink image build code into own recipe. Include the common
parts instead of including a full build recipe and overwriting former set
varaibles.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2
(mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac
wireless router. Additionally, it adds a new profile for devices with
>= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget.
See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9822 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
- SFP: 1x host
Working:
- Board/system detection
- NAND storage detection
- Wireless
- Ethernet
- 1x user LED
- Reset button
- Sysupgrade
Untested:
- SFP cage (probably not working)
Installation:
- Boot initramfs image via TFTP and then flash sysupgrade image
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Apply code from commits 9e1bc27e6d
(ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and
665bb27499 (ar71xx: fix invalid pointer
dereference in rb95x_nand_scan_fixup()) to RB92x devices too.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch converts all apm821xx devices to the device-tree
board-detection method. All instances of the legacy
boardnames (mbl,mr24,...) are converted to "vendor,device"
identifier.
The custom board-detection code in apm821xx.sh is removed as
it no longer serves any purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch enables metadata-supported image verification
for all apm821xx supported devices. Since this method comes
with a built-in image verification tool (fwtool), the previous
image checks can be removed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, the device name handle does not include the
manufacturer. This can make it hard do differentiate
between products from different vendors that have the
same product name. As the handle is used to derive
the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch rename all the DT source files in order to
match upstream's "manufacturer-device.dts" format.
Please note that the DEVICE_DTB isn't changed. This is
because the u-boot of the MyBook Live defines the
fdt_file variable to be "apollo3g/apollo3g.dtb".
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Meraki choose to use their product's codename as the main
compatible string. Mathias Kresin commented that this is
a poor choice as this will confuse the users and devs once
the device-tree compatible is used for board-detection and
possible the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch appends the "apm,bluestone" or "amcc,apollo3g"
machine compatible string to the current device tree source.
Please note that unlike other archs the PPC DT code does
not regard the machine's compatible string as a priority
list. This is explained in the kernel's usage-model.txt as follows:
"PowerPC uses a slightly different scheme where it calls the .probe()
hook from each machine_desc, and the first one returning TRUE is used.
However, this approach does not take into account the priority of the
compatible list, and probably should be avoided for new architecture
support."
For this reason, the "apm,bluestone" compatible string can't be
added to the WNDR4700. As otherwise the target specific pci
fix-up code will get ignored and this causes the ath9k WIFI
to not get initialized.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch sets the BOARD_NAME variable on each affected
apm821xx device. The existing DEVICE_PROFILE and
DEVICE_NAME assignments are deprecated as they no longer
serve any purpose.
The BOARD_NAME variable is used by the sysupgrade-tar
method to specifiy a directory overwrite for the
sysupgrade-$dir directory in the generated tar file.
Keeping the original boardname in this context will be
necessary for targets that utilize the sysupgrade-tar
method. Otherwise, sysupgrade on an previous installation
will not recognize the newly generated images.
This step is necessary since an upcoming patch realigns
the existing shortname for a device with a proper
"manufacturer_device" identifier.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The commit 87b668765e
("image: when using the new image build code, gzip ext4 images by default")
forced that all targets that select the ext4 as the root filesystem
to always compress the generated rootfs. This is fine, but this method
doesn't not allow to append the metadata on a per-target base.
Therefore this patch changes the rootfs image production rule to generate
the gzip step manually. This way the metadata can be appended at a later
date.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
"PandoraBox" is not the name of the manufacturer, it's a firmware made by
the manufacturer actually. Their official English name is "D-Team".
PBR-M1 is the only one they use "PandoraBox" as a brand name. Their other
products are using "Newifi" as their trademark (including Y1 and Y1S which
used to be OEM products for Lenovo).
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Previously Newifi D2 could only use PandoraBox M1's firmware.
It works fine, but LED GPIO is different.
As a result, a separated DTS file for this device should be implemented.
Hardware spec:
* CPU: MTK MT7621A
* RAM: 512MB
* ROM: 32MB SPI Flash
* WiFi: MTK MT7603+MT7612
* Button: 2 buttons (reset, wps)
* LED: 3 single-color LEDs (USB, WiFi 2.4GHz, WiFi 5GHz) &
2 dual-color LEDs (Power, Internet)
* Ethernet: 5 ports, 4 LAN + 1 WAN
Installation method:
Same as Newifi D1, users may need to request unlock code from the device
manufacturer. Otherwise, a SPI flash programmer may be necessary to get
the firmware flashed. After the device is unlocked, press and hold reset
button before power cable plugs in. Then go to http://192.168.1.1 to
upload and flash the firmware package.
Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet
cable, one extra Ethernet port, and an internal antenna, based on the
MediaTek MT7620n chipset.
Specs:
- MT7620n WiSoC @ 600MHz
- 32 MB SDRAM
- 4 MB SPI flash
- 2T2R 2.4GHz WiFi-N
- 1 attached 10/100 Ethernet cable (LAN)
- 1 10/100 Ethernet port (WAN)
- 1 attached USB / barrel 5vdc power cable
- 5 LEDs (see notes below)
- 1 reset button
- 1 UART (3 pads on board)
Installation:
The stock firmware does not support uploading new firmware directly,
only checking the manufacturer's site for updates. This process may be
possible to spoof, but the update check uses some kind of homebrew
encryption that I didn't investigate. Instead, you can install via a
backdoor:
1. Set up a TFTP server to serve the firmware binary
(lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin)
2. Factory reset the device by holding the reset button for a few
seconds.
3. Open the web interface (default IP: 192.168.253.254)
4. Log in with the "super admin" credentials: username `vonets`,
password `vonets26642519`.
5. On the "Operative Status" page, click the text "System Uptime", then
quickly click the uptime value.
6. If successful, an alert dialog will appear reading "Ated start", and
the device will now accept telnet connections. If the alert does not
appear, repeat step 5 until it works (the timing is a bit tricky).
7. Telnet to the device using credentials "admin / admin"
8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin
-r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g
<tftp-server-ip>`
9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4`
10. Reboot
Tested:
- LAN / WAN ethernet
- WiFi
- LAN / WAN / status LED GPIOs (see notes below)
- Reset button
- Sysupgrade
Notes:
LEDs:
The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue
LED for WiFi, and a pair of "status" LEDs connected to the same GPIO
(the blue LED lights when the GPIO is low, and the green when it's
high). I was unable to determine how to operate the WiFi LED, as it
does not appear to be controlled by a GPIO directly.
Recovery:
The default U-boot installation will only boot from flash due to a
missing environment block. I generated a valid 4KB env block using
U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an
external programmer. After this, it was possible to enter the U-boot
commandline interface and download a new image via TFTP (`tftpboot
81b00000 <image-filename>`), but while I could boot this image
sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted
the flash chip. The sysupgrade file can be written to flash at 0x50000
using an external programmer.
Signed-off-by: Andrew Crawley <acrawley@gmail.com>
Add a helper variable which contains the boardname separated from the
vendor name. It allows to switch to a device tree compatible string
based boardname, by keeping the $board:colour:function syntax in
scripts handling/adding config for LEDs.
Boards not using the device tree compatible string as based boardname
are unaffected by the change, since none of them uses a comma in the
boardname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Replace the underline of the device define, to keep the SUPPORTED_DEVICES
in sync with a devicetree compat string based boardname.
Override the default SUPPORTED_DEVICES for board which are having an
userspace boardname with an underline.
Signed-off-by: Mathias Kresin <dev@kresin.me>
