Add missing include of ramips.sh in order to import the missing
ramips_board_name() procedure.
Fixes FS#774.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Specification:
- SoC: MediaTek MT7620A (580 MHz)
- RAM: 64 MiB (Winbond W9751G6JB-25)
- Flash: 16 MiB (Spansion S25FL128SAIF00)
- LAN: x4 100M
- WAN: x1 100M
- Others: USB 2.0, reset button, wps button and 9 LEDs
Issues:
- 5 GHz band is not functional (missing driver support)
Installation:
Asus windows recovery tool:
- install the Asus firmware restoration utility
- unplug the router, hold the reset button while powering it on
- release when the power LED flashes slowly
- specify a static IP on your computer:
IP address: 192.168.1.75;
Subnet mask 255.255.255.0
- Start the Asus firmware restoration utility, specify the sysupgrade
image, and press upload
TFTP Recovery method:
- set computer to a static ip, 192.168.1.75
- connect computer to the LAN 1 port of the router
- hold the reset button while powering on the router for a few seconds
- send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin
tftp> quit
Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
This device exactly same as NBG-419N but with USB port and USB Led.
Specification:
- SoC: Ralink RT3052 (MIPS24Kc) @384MHz
- RAM: 32 MiB
- Flash: 8 MiB
- WLAN: WiSoC 2T2R/300Mbps (2.4GHz)
- LAN: 4x100M
- WAN: 1x100M
- USB: 1x2.0
Installation via serial console (57600 8N1) from TFTP server
- rename the firmware to something shorter, for example
"sysupgrade.bin" (max. 32 chars)
- copy firmware TFTP server's directory
- when you power on device, and see U-Boot log, immediatly push "2"
once.
- You will see this message:
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?
- Push "y", and enter: device IP, then TFTP server's IP, and then
image firmware file name.
The firmware will be downloaded within ~30 seconds and flashed to the
device (It will take about 2 minutes).
Signed-off-by: Alexey Belyaev <spider@spider.vc>
[squash commits, compact commit message, fix compatible string, remove
superfluous pinmuxes]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds the interface-name option for each dhcp config
in /etc/config/dhcp.
With the interface_name option users can define a DNS name for each dhcp section
that will be resolved by dnsmasq with the underlaying interface address.
For example:
config dhcp 'lan'
option interface 'lan'
...
list interface_name 'home.lan'
...
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Build profile for Asmax AR 1004g refers to an invalid DTS "rg100a". The
correct DTS for this device is "ar1004g".
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
It has been shown that the Fritz boxes have the correct mac address set
in the wireless calibration data/eeeprom. Use this mac address as base
for the ethernet and xdsl interface increment/decrement the address to
match the values stored in the tffs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
commit 89878f60f4 x86: lift kernel minimum CPU requirement to Pentium MMX
caused kconfig havoc. Fix this and make sure PAE is enabled even on legacy
CPUs as the minimum required CPU has been Pentium MMX for a while now and
hence PAE is supported even on the x86_legacy target.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Significantly reduces time spent processing those targets and should
also silence some log clutter which could confuse buildbot
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Anything older than that isn't supported since commit f4f8f4a180,
hence also switch to Pentium MMX when building the kernel.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
commit 4b4f739373 switched on HIGHMEM4G which implicitely disabled
PAE and hence also NX and other useful and security-relevant features.
Re-enable PAE by switching to HIGHMEM64G.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If there's a TFTP root directory configured, create it with mkdir -p
(which does not throw an error if the folder exists already)
before starting dnsmasq. This is useful for TFTP roots in /tmp, for example.
Originally submitted by nfw user aka Nathaniel Wesley Filardo
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.
Hopefully fixes FS#758
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Module definitions for kmod-wdt-sunxi and kmod-eeprom-sunxi are removed
(wdt-sunxi was builtin anyways; nvmem-sunxi, which is the new name of
eeprom-sunxi is changed to builtin). As kmod-eeprom-sunxi was specified
in DEFAULT_PACKAGES, but not available on kernel 4.4, it was breaking the
image builder.
Support for kmod-sunxi-ir is added for kernel 4.4 (it is unclear why it
was disable before, it builds fine with with kernel 4.4).
Condtionals only relevant for pre-4.4 kernels are removed from modules.mk,
as sunxi does't support older kernels anymore.
Fixes FS#755.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
It was originally only enabled for the "32" subtarget along with the
"usb" feature which is now also shared by the "64" target
This should fix the phase1 build of armvirt/64
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Do not assign the CPU port twice, this confuses LuCI and possible other
programs relying on topology information in board.json.
Ref: https://github.com/openwrt/luci/issues/1086
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Setting legacy_rates to 0 disables 802.11b data rates.
Setting legacy_rates to 1 enables 802.11b data rates. (Default)
The basic_rate option and supported_rates option are filtered based on this.
The rationale for the change, stronger now than in 2014, can be found in:
https://mentor.ieee.org/802.11/dcn/14/11-14-0099-00-000m-renewing-2-4ghz-band.pptx
The balance of equities between compatibility with b clients and the
detriment to the 2.4 GHz ecosystem as a whole strongly favors disabling b
rates by default.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, defaults change]
When sta is configured, hostapd receives 'stop' and 'update' command from
wpa_supplicant. In the update command, hostapd gets sta parameters with
which it configures ap.
Problem is, with the default wireless configuration:
mode:11g freq:2.4GHz channel:1
If sta is connected to 5GHz network, then ap does not work. Ideally with
340-reload_freq_change.patch hostapd should reload the frequency changes
and start ap in 5GHz, but ap becomes invisible in the network.
This issue can be reproduced with following /etc/config/wireless:
config wifi-device radio0
option type mac80211
option channel 1
option hwmode 11g
option path 'virtual/uccp420/uccwlan'
option htmode 'none'
config wifi-iface 'ap'
option device 'radio0'
option encryption 'none'
option mode 'ap'
option network 'ap'
option ssid 'MyTestNet'
option encryption none
config wifi-iface 'sta'
option device radio0
option network sta
option mode sta
option ssid TestNet-5G
option encryption psk2
option key 12345
This change updates current_mode structure based on configured hw_mode
received from wpa_supplicant. Also prepare rates table after frequency
selection.
Signed-off-by: Abhilash Tuse <Abhilash.Tuse@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, patch refresh]
Commit 2036ae4 (base-files: support hostname and ntp servers through board.d)
was supposed to implement these procedures but lacked the required changes
to uci-defaults.sh.
Add the missing procedures now to fix config generation on targets relying
on hostname or NTP server presetting.
Fixes FS#754.
Reported-by: Cristian Morales Vega <cristian@samknows.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When busybox customisation is enabled, we should depend on config
symbols CONFIG_BUSYBOX_CONFIG_xxx to form alternatives specs
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Otherwise ipkg packages may wrongly take on alternatives specs of
another package sharing the same package Makefile
Fixes FS#753
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
A number of small tweaks & improvements on the way to a final release.
Most notable:
Improve DHCPv4 address-in-use check.
Remove the recently introduced RFC-6842 (Client-ids in DHCP replies)
support as it turns out some clients are getting upset.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Changes since last version
546bc72 pkg: alternatives support
7a96972 libbb: xreadlink: fix memory leak on failure case
3f13edd pkg_run_script: use pkg->dest in half installed case
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
It's a list of specs of the following form seprated by commas to
describe alternatives provided by this package
<prio>:<path>:<altpath>
<path> will be a symbolic link to <altpath> of the highest <prio>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
With update of ARC tools to arc-2016.09 based on GCC v6.x
we have to bump Linux kernel version so both toolchain and
the kernel use the same ARC ABIv4.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
With update of ARC tools to arc-2016.09 based on GCC v6.x
we have to bump Linux kernel version so both toolchain and
the kernel use the same ARC ABIv4.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
arc-2016.09 is the most recent toolchain for ARC cores and
it is based on top of upstream Binutils 2.27 and GCC 6.2.1.
With updated major version of GCC we copied all GCC 6.x patches
for ARC as well as Bintils 2.27 patches.
Note that toochain sports ARCv4 ABI and so must be used
with 4.8+ Linux kernels. Even though it will build v4.4 kernel
perfectly fine on attempt to run user-space apps they won't
work with older kernel. That said previuosly sent RFC patches with
Linux kernel update are required:
[1] https://patchwork.ozlabs.org/patch/726686/
[2] https://patchwork.ozlabs.org/patch/726687/
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
DWC3 driver uses of_usb_get_phy_mode() which is
implemented in drivers/usb/phy/of.c and in bare minimal
configuration it might not be pulled in kernel binary.
In case of ARC or ARM this could be easily reproduced with
"allnodefconfig" +CONFIG_USB=m +CONFIG_USB_DWC3=m.
On building all ends-up with:
---------------------->8------------------
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Building modules, stage 2.
MODPOST 5 modules
ERROR: "of_usb_get_phy_mode" [drivers/usb/dwc3/dwc3.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
---------------------->8------------------
This was affecting Lede in case of CONFIG_ALL_KMODS=y.
The patch is already scheduled for v4.12 and once it is backported to
4.9.y it must be removed from here.
Note this patch makes sense not only for ARC instead it fixes
a generic issue which may affect more arches and platforms thus
putting it in "generic/" folder.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [patch rename]
Since commit:
7120438e5d
Seems that fsl_rstcr_restart() has been converted
to a reset handler and dropped as hook/callback.
Apply the same to the `tl_wdr4900_v1` target.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Re-applied patches:
001-powerpc-85xx-add-gpio-keys-to-of-match-table.patch
100-powerpc-85xx-tl-wdr4900-v1-support.patch
Dropped patch:
200-spi-fsl-espi-preallocate-local-buffer.patch
now part of kernel upstream hash
1423877b73
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
