For the pure convenience of having a correctly named
image and system name in /proc/cpuinfo , until we can
do that by having system names in DTS...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 33224
The TL-WDR3600 is identical to the TL-WDR4300 with the exception that is has
only two antennas.
[juhosg: remove the custom machine type, change the board name instead]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 33219
Here is the uci-defaults version of the led support for
the Buffalo WLAE-AG300N.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32932
The patch set for Buffalo WLAE-AG300N initial support.
There is another patch for wireless led support that
is posted separately.
Note on serial console:
This unit has buffalo standard 4 pin console, but the unit may not power
on if some console apparatus is connected. This is probably due to some
electronic interaction between the unit's electronic power switch circuit
and the serial console apparatus. If this happens, it is required to power
on the unit without the console, then quickly (re-)attach it.
[juhosg: fix coding style]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32931
This patch helps properly detect a WNDRMAC device. Before this
patch the model is detected as "NETGEAR ?????????N".
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32453
Support for TP-Link TL-MR3040. Power LED not working - always on red, after
start should be green.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 31845
On TP-Link TL-WR741ND version 4, the WLAN LED must be configured to work.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 31461
Great collaboration on these two fantastic routers on the openwrt forum:
https://forum.openwrt.org/viewtopic.php?id=32320
Above all kudos to aryufan. Well done and thank you everyone else who
contributed.
To-Do: LED for wlan is not yet activated
To-Do: TxPower over 20dBm (RB751U) or 22dBm (RB751G) are not accepted by
the router
Signed-off-by: Hanno Schupp <hanno.schupp@gmail.com>
[juhosg: fix line wrapped patch, fix checkpatch errors, add missing
kernel patches]
SVN-Revision: 31208
This patch adds support for D-LINK DIR-615 E4 board. It's mostly based
on the existing support for DIR-600 A1, with some changes in the leds
configuration.
It's an updated version of the patch that reliably works on my hw for
about a year (it was built from trunk on Jan 2011). When I decided to
update the firmware and checked for the current support for that device,
I also found previously posted patches by Alexey Loukianov that
mentioned some stability issues. I'm not sure where could be the
difference, the patches are very similar except the wmac led pin number
- I was using 1, and those patches used 17.
[juhosg: add 3.2 support]
Signed-off-by: Vadim Girlin <vadimgirlin@gmail.com>
SVN-Revision: 29973
Adds support for TL-MR11U, a portable router with very similar
hardware to the TL-WR703N and TL-MR3020, but with an onboard
2000mAh battery.
Tested, working:
All interfaces (Ethernet, 802.11n, USB)
WPS & Reset switches (Power appears to be a hardware slider)
Ethernet, Wifi, 3G LEDs (Power & charging LEDs hardware controlled)
Sysupgrade
[juhosg: fix indentations to use TABs instead of spaces, fix 3.2 patch
breakage]
Signed-off-by: Simon Taylor <simon.taylor.uk@gmail.com>
SVN-Revision: 29972
This patch adds support for Compex WPE72 bare board and Compex WPE72NX
Indoor Access Point.
[juhosg: add support to 3.2 as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29912
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29905
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.
SVN-Revision: 29662
