Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The stock firmware uses the single LED as status indicator only. Using the
same LED both for status and as ethernet indicator is uncommon, and has
been confusing users who were using the device as a WLAN mesh node (so the
LED was just off, as no ethernet was connected).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Several legacy images were not buildable because of missing profile
definitions in legacy-devices.mk since MultiProfile was removed. Update
legacy-devices.mk to provide all necessary profiles, and change ordering
to match legacy.mk.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The network defaults for the WZR-HP-G300NH and CR3000 models wrongly set the
lan interface to a vlan tagged device while the switch was set up in untagged
mode, leading to broken lan side ethernet connectivity by default.
Fix the issue by emitting untagged interfaces, consistent with the switch
setting on the device.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers
Default configuration:
- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space
Flash instruction (do it under U-Boot, using RS232):
1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers
Default configuration:
- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
It was intended as a workaround when jffs2 eof mark was included in the
checksum calculation in seama header. When qihoo-c301 support was
introduced the board name was not inserted into the case list (because I
was not aware of it's existence), but the issue was fixed by excluding
the jffs2 marker as part of the checksum data
Now we are at it, drop it.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This patch adds support of Mikrotik yaffs2 filesystem image for kernel file
and tools/kernel2minor package.
We neede this to boot kernel through RouterBoot on new Mikrotik NOR flash devices.
Signed-off-by: Sergey Sergeev <adron@yapic.net>
In new kernels we should use clk_prepare_enable instead of clk_enable
since clk_enable does not make proper initialization that leads
to rise WARN_ON messages and not working spi bus on the device.
Signed-off-by: Sergey Sergeev <adron@yapic.net>
rootfs part needs to be aligned to erase block size which is passed as
the 6th argument to Image/Build/Seama and is now 65536 since commit
commit 5119ee9 "ar71xx: fix bogus hardcoded kernel image size for Seama
images (fixes#20585)", but $(($(6) - 64)) still assumes that the
argument is a limit on kernel partition size, i.e. 1310720, so the
generated factory image is wrong in that the kernel will fail to find
the rootfs (FlySpray link at [1])
This patch will workaround it with the following steps
1. Calculate the required space for seama header and META data in step 5
2. Pre-padding 64 bytes to lzma-compressed loader
3. Generate correctly padded image-$(2).tmp
4. Strip out the padding
5. Seal it with seama utility
While at it convert seama to new build method
[1] FS#35 - mynet-n750 factory images don't find root partition,
https://bugs.lede-project.org/index.php?do=details&task_id=35
Reported-by: Steven Haigh <netwiz@crc.id.au>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Remove kmod-crypto-deflate and kmod-ledtrig-gpio as the device works the
same by default without them
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
- Add missing macro to trigger the generation of 64k padded squashfs images
- Revert Zcomax image generation to use the prepared 64k squashfs image
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
- Remove old style device profiles and convert them to device definitions
within the image building code
- Fix the legacy build macros for the changed eval depth in the legacy
image build wrapper
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Should fix LAN speed issues on some devices. This is an updated version
of the previously reverted commit with the same name.
It improves the check for MACs connected to a built-in switch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit 59e98b27c9.
and
Revert "ar71xx: merge profiles into image building code"
This reverts commit 636089ead6.
these are still causing issues
Signed-off-by: John Crispin <john@phrozen.org>
After the conversion from legacy device profiles to the newer profile
information embedded in the image building code, the legacy recipes got
triggered twice with different eval depths, leading to shell syntax errors
when processing certain images.
The double processing was caused by the remaining Image/Build macro in
legacy.mk which serves as main entry point for the new style image build code
in conjunction with the newly introduced LegacyDevice/* macros which caused
the legacy image build fallback code to kick in.
In order to fix the issue, rework all legacy macros to work under the legacy
image build wrapper and remove the Image/Build macro of legacy.mk to prevent
legacy profiles getting executed in the context of the new build code.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The patch has been run-tested and the relevant dmsg logs are as the
following
[ 0.762447] Creating 5 MTD partitions on "spi0.0":
[ 0.767217] 0x000000000000-0x000000010000 : "u-boot"
[ 0.775139] 0x000000010000-0x000000020000 : "bdinfo"
[ 0.781014] 0x000000020000-0x000000fe0000 : "firmware"
[ 0.810558] 2 uimage-fw partitions found on MTD device firmware
[ 0.815043] 0x000000020000-0x000000170000 : "kernel"
[ 0.821925] 0x000000170000-0x000000fe0000 : "rootfs"
[ 0.827587] mtd: device 4 (rootfs) set to be root filesystem
[ 0.831937] 1 squashfs-split partitions found on MTD device rootfs
[ 0.837983] 0x0000005c0000-0x000000fe0000 : "rootfs_data"
[ 0.845621] 0x000000fe0000-0x000000ff0000 : "backup"
[ 0.851445] 0x000000ff0000-0x000001000000 : "art"
While at it, convert to new build method
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Reordered the VLANs so the LAN ports are set to VLAN 1 and the WAN port is set to VLAN 2, as in the other routers in the config file. Moreover, this model had this VLAN mapping in OpenWRT Chaos Calmer. It seems that the VLAN were switched when fixing a bug in the port mapping ( OpenWRT changeset 47799 )
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.
Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
The CPE210 was still described for the OEM upgrade as compatible,
even the wireless configuration isn't compatible anymore between
both series (2ghz and 5ghz).
Update the CPE210 image profile to use the new profile.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The CPE210's ancestor is the CPE510 not the other way around. The device
profile is also named after the CPE510.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
RB912 has one usb shared between external USB and miniPCIe slot. GPIO52 can
reroute power to external USB (=1) or internal miniPCIe slot (=0)
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
The cpe510 has two calibration tables. The first calibration
table requires to modify ath9k driver to work (patched tx gain table).
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The CE image format used by OpenMesh can contain extra blocks which
are not used for flashing. Only the first three embedded images
(fwupgrade.cfg, kernel, rootfs) are required in this order to successfully
flash an image via sysupgrade. All extra embedded images should be ignored
for the available devices.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The platform_check_image_openmesh function used break statements to signal
that the board name matched the image target. This worked because the
sysupgrade binary checked the image inside a loop. The break statement
stopped the loop and skipped any additional check.
Instead the check should be done without such sideeffects by simply
combining the board names and image targets. Only a mismatch should cause a
negative result for the caller and skipping of the additional checks.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Some OpenWrt based firmwares like Gluon expect that a sysupgrade image
exists when a device firmware can be updated via sysupgrade. This image
wasn't created until now because OpenMesh devices use the same image for
factory and sysupgrade flash. Copying the image from *factory.bin to
*sysupgrade.bin is therefore enough to make the sysupgrade functionality
visible.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The LNA improves the rx path. Within a simple test setup
it improved the signal from -60dbm to -40dbm.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
- CPU QCA9531-BL3A
- RAM: 64MB
- flash: 16MB
- USB
AP143 platform, similar to tl-wr841n v10/v11, but with USB
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.
Signed-off-by: P.Wassi <p.wassi at gmx.at>
