This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch aligns the device-tree file with the latest
guidelines.
- No longer include qcom-ipq4019-ap.dk01.1.dtsi. This
file is only partially upstream and therefore subjected
to changes that might not be compatible with the board.
As a result, the definitions from the file have been
copied into this dts.
- exclusively use decimal GPIO addresses.
- reorganize the reserved-memory layout to waste less
memory. There's no point in keeping the u-boot loader
around. This should also make it possible to create
an image that will boot with the original EVA/ADAM2 loader
without needing to install the modified u-boot loader.
And finally mark the "tz-apps" as reusable.
There isn't a way to upload apps to the trust-zone in OpenWrt
yet. But it might see some use in the future as a "secure"
key-store/TPM.
- sort the first-level nodes alphabetically.
- sort nodes with an address by the address.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.
It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.
Fixes: 33f09cf151 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3
Commit message:
"During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated."
Change-Id: I537dc810f6cb2a46664ee674840145066432b957
Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org>
(cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)"
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
A newer clk and cpufreq drivers for ipq806x platform had been sent upstream.
A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing).
Following patches are removed:
- 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer.
- 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch.
- 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode.
EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode.
In previous commit we've added the support for this option, so enable it in DT for affected devices.
QSDK ref:
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506
While at it move the phy transmit termination offset value into dtsi file as it's platform specific.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues.
https://bugs.lede-project.org/index.php?do=details&task_id=1197
This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch
Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant
Unfortunately qca developers do not bother to push it upstream.
Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration.
Fixes: FS#1197 and probably others
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove leftover code used for legacy images. There are no relevant
binary differences for the images after removing the legacy leftovers.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Initialise the filesystem specific build command. Otherwise it will be
unintended inherit to following images and will cause a wrong image
format.
The issue is around for ages but was only recently triggered due to the
added support for the Openmesh a42.
Fixes: FS#1276
Signed-off-by: Mathias Kresin <dev@kresin.me>
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The kernel driver gpio-wdt or the userspace tool om-watchdog can be used to
trigger external gpio watchdog chips. The gpio-wdt driver has the benefit
that it can be configured together with the rest of the device in the DTS
and better integrates in the OpenWrt via procd.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.
None of the current boards use a comma in the boardname, so they
will be unaffected.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This changes the cmdline from:
Kernel command line: root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
to
Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p5
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
As a consequence booting from the alternative dual-boot partition set
(root=/dev/mmcblk0p8) becomes possible.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)
First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize
Further upgrades via sysupgrade.
Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition
Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.
Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.
Changes since v2:
- based on dts(i) rework/cleanup submitted:
http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Supported frequencies of all ipq40xx chips are 48, 200, 500 and 716.8 MHz.
Previous 666MHz setting was most likely related to instability of early
chips/boards made before mass production.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.
interface new/ OEM MAC old MAC
wlan-2.4g (phy1): ethaddr undefined
wlan-5g (phy0): ethaddr + 1 undefined
lan : ethaddr + 2 ethaddr
wan : ethaddr + 3 ethaddr + 1
This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split
into the readonly squashfs and ext4 for the overlay. This adds the
required package to the device packages to allow mounting the overlay
by default.
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect)
Before this commit, the ext4 based overlayfs could not be mounted,
which left only the tmpfs based/ volatile emergency overlay in place.
Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
IMG_PREFIX can be modified in ImageBuilder by passing EXTRA_IMAGE_NAME
on command line, but Image/Prepare is not run in ImageBuilder. This
causes missing files when IMG_PREFIX is used for target file names in
Image/Prepare, then as source file names in Image/BuildKernel or
Image/Build.
Fix this by using a fixed output file name in Image/Prepare, and copy to
the expected file name in Image/BuildKernel instead, which is run by
ImageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Zyxel NBG6817 features a WiFi button, which becomes functional by setting
correct GPIO. It is a switch-type button, so it emits KEY_RFKILL on each ON
and OFF state. This is achieved by setting input-type to EV_SW.
Signed-off-by: Tolga Cakir <tolga@cevel.net>
Refresh patches.
Compile-tested on ipq8065/nbg6817 and x86/64.
Runtime-tested on ipq8065/nbg6817 and x86/64.
Fixes CVE-2017-1000251.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
[adapt qcom_nandc.c patches to match upstream changes, test ipq8065/nbg6817]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Refresh patches.
Adapt 704-phy-no-genphy-soft-reset.patch.
Remove brcm2708/950-0005-mm-Remove-the-PFN-busy-warning.patch.
Compile-tested on brcm2708/bcm2708 and x86/64.
Runtime-tested on brcm2708/bcm2708 and x86/64.
Fixes the following vulnerabilities:
- CVE-2017-7533
- CVE-2017-1000111
- CVE-2017-1000112
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.
The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
- Refreshed all patches
- Removed upstreamed
- Adapted 4 patches:
473-fix-marvell-phy-initialization-issues.patch
-----------------------------------------------
Removed hunk 5 which got upstreamed
403-net-phy-avoid-setting-unsupported-EEE-advertisments.patch
404-net-phy-restart-phy-autonegotiation-after-EEE-advert.patch
--------------------------------------------------------------
Adapted these 2 RFC patches, merging the delta's from an upstream commit
(see below) which made it before these 2.
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-
stable.git/commit/?h=v4.9.36&id=97ace183074d306942b903a148aebd5d061758f0
180-usb-xhci-add-support-for-performing-fake-doorbell.patch
-----------------------------------------------------------
- Moved fake_doorbell bitmask due to new item
Compile tested on: cns3xxx, imx6
Run tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.
The list of binaries is also slightly cleaned up and duplicates are
removed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
RAMFS_COPY_* are moved to platform.sh toplevel. The unneeded
linksys_preupgrade function is removed, and the nand_do_upgrade call is
moved to platform_do_upgrade.
Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This change enables .itb image generation for AP148,
It will help us to boot and test AP148 with NOR flash.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)
Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
As of now OTP is being correctly parsed and the driver requires to parse pre-caldata to follow corresponding routine.
Rename cal file into pre-calfile so the board initialized correctly with API 2 board data (board-2.bin).
Also remove the now unneeded for qca9984 board.bin symlink to 5GHz calfile.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Fixes the following security vulnerabilities:
CVE-2017-8890
The inet_csk_clone_lock function in net/ipv4/inet_connection_sock.c in the
Linux kernel through 4.10.15 allows attackers to cause a denial of service
(double free) or possibly have unspecified other impact by leveraging use
of the accept system call.
CVE-2017-9074
The IPv6 fragmentation implementation in the Linux kernel through 4.11.1
does not consider that the nexthdr field may be associated with an invalid
option, which allows local users to cause a denial of service (out-of-bounds
read and BUG) or possibly have unspecified other impact via crafted socket
and send system calls.
CVE-2017-9075
The sctp_v6_create_accept_sk function in net/sctp/ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.
CVE-2017-9076
The dccp_v6_request_recv_sock function in net/dccp/ipv6.c in the Linux
kernel through 4.11.1 mishandles inheritance, which allows local users to
cause a denial of service or possibly have unspecified other impact via
crafted system calls, a related issue to CVE-2017-8890.
CVE-2017-9077
The tcp_v6_syn_recv_sock function in net/ipv6/tcp_ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.
CVE-2017-9242
The __ip6_append_data function in net/ipv6/ip6_output.c in the Linux kernel
through 4.11.3 is too late in checking whether an overwrite of an skb data
structure may occur, which allows local users to cause a denial of service
(system crash) via crafted system calls.
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-8890
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9074
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9075
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9076
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9077
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9242
Ref: https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.9.31
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This change add IPQ40xx AP-DK04.1-C1 board image support,
enables ubi image for IPQ40xx AP-DK04.1-C1 board and also
add sysupgrage support for AP-DK04.1-C1 and generates a
sysupgrade.tar image.
Testing:
*Tested on IPQ40xx AP-DK04.1-C1:
a. NAND boot
b. ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
This change adds QPIC BAM dma and NAND driver node's in IPQ4019
device tree, also enable this for AP-DK04.1 based boards.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
This change adds support for below:
- Bam transaction which will be used for any NAND request.
- Reset function for NAND BAM transaction
- Add support for additional CSRs.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
The existing qcom_nand driver supports ADM DMA which is mainly
required for ipq806x family based boards,
IPQ40xx based boards uses BAM DMA in NAND driver, so this patch
adds BAM DMA support with compatible string as qcom,ebi2-nandc-bam.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
GPIO_PULL bits configurations in TLMM_GPIO_CFG register
differs for IPQ40xx from rest of the other qcom SoC's.
This change add support to configure the msm_gpio_pull
bits for ipq40xx, It is required to fix the proper
configurations of gpio-pull bits for nand pins mux.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
The device tree is at /proc/device-tree/ without a base subdir.
Fixes: da472e5b30 ("treewide: access device tree from userspace via /proc/")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Access the device tree via /proc/device-tree/ is the documented way to
access the properties. Everything else might not work in future.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not assign the CPU port twice, this confuses LuCI and possible other
programs relying on topology information in board.json.
Ref: https://github.com/openwrt/luci/issues/1086
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:
root@LEDE:/# rmmod dwc3-of-simple
[ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.391931] usb usb4: USB disconnect, device number 1
[ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.406685] usb usb3: USB disconnect, device number 1
[ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.
Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.
At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.
root@LEDE:/# rmmod dwc3
[ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.827412] usb usb4: USB disconnect, device number 1
[ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.842314] usb usb3: USB disconnect, device number 1
[ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.857882] usb usb2: USB disconnect, device number 1
[ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.873696] usb usb1: USB disconnect, device number 1
[ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#
For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0
The patch however addresses the clock assignment from the Netgear R7500
dts file and backs off the previous attempt.
Now unloading and repeated module loading is working just fine.
root@LEDE:/# rmmod dwc3-of-simple
[ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.089765] usb usb4: USB disconnect, device number 1
[ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.104522] usb usb3: USB disconnect, device number 1
[ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.120396] usb usb2: USB disconnect, device number 1
[ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.135948] usb usb1: USB disconnect, device number 1
[ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#
Fixes: dwc3-of-simple module unloading for Netgear R7500
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
The patch follows the qualcomm code comments setting
SSUSB_CTRL_TEST_POWERDOWN to 0x1 and is testing and clearing the
bit during USB superspeed PHY init. According to Andy Gross it
needs to be BIT(26).
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Use the stateless 4-byte op codes for this flash chip to fix reboot
hangs on SoCs expecting the flash chip in 3-byte mode.
Fixes: FS#179
Signed-off-by: Mathias Kresin <dev@kresin.me>
Split the fritz-tools into subpackages. fritz_tffs_read is usefull for
all Fritz boards where fritz-cal_extract is only required for the
Fritz 4040 at the moment.
Rename the tffs related binary to the more catchy name fritz_tffs and
move the whole package to utilities since the package doesn't really
provide a firmware file.
Make the fritz-tools available for all targets and build them shared.
The tffs is used by avm on lantiq and ar71xx as well.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:
root@LEDE:/# rmmod dwc3-of-simple
[ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.391931] usb usb4: USB disconnect, device number 1
[ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.406685] usb usb3: USB disconnect, device number 1
[ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.
Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.
At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.
root@LEDE:/# rmmod dwc3
[ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.827412] usb usb4: USB disconnect, device number 1
[ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.842314] usb usb3: USB disconnect, device number 1
[ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.857882] usb usb2: USB disconnect, device number 1
[ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.873696] usb usb1: USB disconnect, device number 1
[ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#
For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0
The patch however addresses the clock assignment from the .dtsi
file. Most probably it went into openwrt here:
https://dev.openwrt.org/browser/trunk/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch?rev=45261
copied from Qualcomms attempt here: https://lkml.org/lkml/2015/11/20/116
Now unloading and repeated module loading is working just fine,
no matter if you'd remove dwc3-of-simple or dwc3.
root@LEDE:/# rmmod dwc3-of-simple
[ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.089765] usb usb4: USB disconnect, device number 1
[ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.104522] usb usb3: USB disconnect, device number 1
[ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.120396] usb usb2: USB disconnect, device number 1
[ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.135948] usb usb1: USB disconnect, device number 1
[ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#
Fixes: dwc3-of-simple module unloading
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Allow module unloading by fixing a mistake.
qcom_dwc3_phy_write_readback() is expecting (phy, offset, mask, value)
while the mistake was calling it with (phy, offset, value, mask)
The patch is swapping value and mask.
Without the patch unloading the dwc3 module was showing a
write to QSCRATCH failed and repeated module loading was
failing:
root@LEDE:/# rmmod dwc3
[ 19.167998] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 19.168084] usb usb4: USB disconnect, device number 1
[ 19.173371] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 19.177134] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 19.182960] usb usb3: USB disconnect, device number 1
[ 19.189023] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 19.192989] qcom-dwc3-usb-phy 110f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED
[ 19.199064] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 19.205912] usb usb2: USB disconnect, device number 1
[ 19.211611] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 19.215905] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 19.221751] usb usb1: USB disconnect, device number 1
[ 19.227307] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 19.231795] qcom-dwc3-usb-phy 100f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED
root@LEDE:/# modprobe dwc3
[ 29.583343] phy phy-100f8830.phy.4: phy init failed --> -110
[ 29.583399] dwc3 10000000.dwc3: failed to initialize core
[ 29.588169] dwc3: probe of 10000000.dwc3 failed with error -110
[ 29.652943] phy phy-110f8830.phy.2: phy init failed --> -110
[ 29.652988] dwc3 11000000.dwc3: failed to initialize core
[ 29.657735] dwc3: probe of 11000000.dwc3 failed with error -110
root@LEDE:/#
With patch repeated module unloading and loading is working good:
root@LEDE:/# rmmod dwc3
[ 22.622214] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 22.622298] usb usb4: USB disconnect, device number 1
[ 22.627401] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 22.631492] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 22.637054] usb usb3: USB disconnect, device number 1
[ 22.643721] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 22.647421] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 22.652910] usb usb2: USB disconnect, device number 1
[ 22.659219] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 22.662768] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 22.668604] usb usb1: USB disconnect, device number 1
[ 22.674803] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# modprobe dwc3
[ 25.404592] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.404694] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 25.409444] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 25.416589] xhci-hcd xhci-hcd.0.auto: irq 168, io mem 0x10000000
[ 25.426509] hub 1-0:1.0: USB hub found
[ 25.431626] hub 1-0:1.0: 1 port detected
[ 25.435472] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.439206] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 25.444573] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.452926] hub 2-0:1.0: USB hub found
[ 25.460420] hub 2-0:1.0: 1 port detected
[ 25.525037] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 25.525099] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 25.529750] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 25.537002] xhci-hcd xhci-hcd.1.auto: irq 169, io mem 0x11000000
[ 25.546583] hub 3-0:1.0: USB hub found
[ 25.551997] hub 3-0:1.0: 1 port detected
[ 25.555734] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 25.559621] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 25.564942] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.573063] hub 4-0:1.0: USB hub found
[ 25.580842] hub 4-0:1.0: 1 port detected
root@LEDE:/#
Fixes: dwc3 module unloading
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Makes use of the syscon tcsr and enables both USB ports. Cleans up
qcom-ipq8064.dtsi from previous attempts.
Fixes FS#497
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Current driver shows temp in full degrees while other apps await it
to be in millidegrees.
Initially the driver represents termal data in millidegrees but then
it gets divided by TSENS_FACTOR. So lets just set it to '1'.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches
the ath10k chipset
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
This patch adds support for AVM FRITZ!Box 4040.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB Nanya NT5CC128M16IP
FLASH: 32 MiB MXIC MX25L25635FMI
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one WLAN and one WPS button
LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1. The SoC's serial port is right
next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
header for it. Use a multimeter to figure out the pinout!
This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.
Install Procedure:
0. It's highly recommended to connect to the serial port.
The serial settings are listed above.
1. install a u-boot image for AVM Fritz!Box 4040
(see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
<https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
2. upload the initramfs.itb image via tftp (u-boot listens to
192.168.1.1 - use binary transfer mode!)
3. connect to the FB4040 and use sysupgrade sysupgrade.bin
to install the image.
Works:
- Switch and Ethernet (99%)
- Buttons (WLAN, WPS)
- FLASH (1 x 32MiB NOR Chip)
- WLAN2G and WLAN5G
- CPUFREQ scaling
- PRNG
- serial
- Crypto Accelerator
- sysupgrade (Read the flash instructions to avoid bricking)
- full LEDE Install (Read the flash instructions to avoid bricking)
- LEDs (Power, WAN, Info (red and amber), LAN)
The LEDs are connected to the QCA8075 LED ports.
The AR40xx driver contains a gpio-controller to
handle these special "GPIOs".
- USB Both 3.0 and 2.0 ports
- many packages from other ARMv7 boards
(This does include the RaspberryPi Model 2!)
- ...
Not planned:
- WAN<->LAN short-cut
- Qualcomm Secure Execution Environment
- ...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Add back support for the independent_clocks definition that has been
removed between kernel 4.4 and 4.9 by upstream commits
eb96924acddc709db58221c210ca05cd9effb1df and
e86eee6bc2aaa6b3637f6497b26beee09a91bde9
* extend the new cpufreq_dt_platform_data definition in cpufreq-dt.h
* revert the removal of its usage in cpufreq-dt.c
* use new cpufreq-dt.h in qcom-cpufreq.c
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
At the moment as a workaround definition for scm firmware in DT is used as if it is
apq8064 board. This leads to incomplete scm firmware initialization and as a result
cpuidle driver fails to configure.
By design unlike other qcom boards ipq do not use clocks to connect to scm.
Considering this we're removing from DT and scm driver clocks for ipq boards.
As a result cpuidle does not produce errors about failed configuration anymore.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
