Currently, multicast packets from an STA are sent to any according
multicast listener directly through the bridge multicast-to-unicast
feature. Unfortunately, so far this includes the originating STA, too,
resulting in multicast packets being echo'ed back to the originating STA
if it itself is a multicast listener for that group.
This behaviour breaks IPv6 duplicate address detection: An IPv6 Neighbor
Solicitation for IPv6 Duplicate Address Detection is being echo'ed back,
resulting in the host falsely detecting an address collision, which
makes the node unable to claim an IPv6 address and use IPv6 in general.
Mac80211 unfortunately only prevents the echoes for us for multicast
frames. For the multicast frames cast to a unicast destination we'll
need to take care of excluding the originator ourselves.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 46765
Add an upstream fix for /proc/net/route causing missing routes doing
several continued reads from it.
Only 4.1+ is affected.
Closes#20403.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46726
A call to pskb_may_pull() might reallocate skb->data. Therefore we
should only assign the src-pointer after any potential reallocations.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46721
This reverts commit a080e8e1943156168913d0353a2e99d1151102aa.
It did not fix the problem but just hid some symptom. The real issue was
that IGMP/MLD report suppression was not considered for the
multicast-to-unicast feature. A recent netifd which isolates IGMP/MLD
reports between STAs by utilizing AP-isolation and bridge-hairpinning
should have fixed this.
It is perfectly fine to apply multicast-to-unicast to IPv6 Neighbor
Solicitations, too (once that feature is configured correctly).
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46720
Remove 131-MIPS-export-get_c0_perfcount_int.patch which was already applied
in 4.1.6. This fixes the following build error:
arch/mips/ath79/setup.c:217:77: error: redefinition of '__kstrtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:77: note: previous definition of '__kstrtab_get_c0_perfcount_int' was here
arch/mips/ath79/setup.c:217:350: error: redefinition of '__ksymtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:350: note: previous definition of '__ksymtab_get_c0_perfcount_int' was here
scripts/Makefile.build:258: recipe for target 'arch/mips/ath79/setup.o' failed
Reported-by: swalker
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46715
Properly treat -ENOSYS as no PHY, else ehci-orion won't work without
generic phy support.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46711
This also clears any bootloader-set FDB defaults. This had
caused issues creating port-based VLANs when mappings
overlapped previous VLANs. Packets destined to a port
not in the default port group flooded all ports.
Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC)
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46699
no-op since 2.6.35
removed in Kernel 4.1
see https://lwn.net/Articles/380931/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46671
The "linux,part-probe" dts parsing is a pretty neat generic feature.
It has been posted to kernel.org and could easily be reused by all
targets.
This change moves the patch to the 3.18 and 4.1 generic folders, and
makes the feature available to all platforms who may want to use it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46654
In addition to the update this also fixes compile problems with kernel 4.1.
This closes#20323.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46609
This patch was missing for kernel 4.0 and 4.1 in r46464. I also
replaced the version in OpenWrt with the version which went upstream
into the Linux mainline kernel.
This closes#20193 and #20192
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46493
REGMAP_MMIO is a hidden symbol, so it cannot be directly selected. If nothing
selects it, it will fail the build with:
ERROR: module '/store/buildbot/slave/slave/rb532/build/build_dir/target-mipsel_mips32_musl-1.1.10/linux-rb532/linux-3.18.19/drivers/base/regmap/regmap-mmio.ko' is missing.
make[2]: *** [/store/buildbot/slave/slave/rb532/build/bin/rb532/packages/base/kmod-regmap_3.18.19-1_rb532.ipk] Error 1
Fix this by adding a description to allow selecting it manually.
Fixes: r46451 ("kmod-regmap: enable MMIO support")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46485
NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.
This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position) and an E3372 device (which mandates NDP
to be after indexed datagrams).
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46464
If a link goes down, don't flush the complete ARL table.
Only flush the entries for the respective port.
Don't touch ARL table if a link goes up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46381
Adds functions for flushing ARL table entries per port.
Successfully tested on AR8327. Implementation for AR8216/AR8236/AR8316
is based on the AR8236 datasheet and assumes that the three chips
share a common ATU register layout.
Compile-tested only for AR8216/AR8236/AR8316.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46380
Adds the chip-specific part of reading ARL table for AR8216/AR8236/AR8316.
It's based on the AR8236 datasheet and compile-tested only as I couldn't
find datasheets for AR8216/AR8316 and don't own devices with these chips.
The existing ar8216_atu_flush implementation was used for all three
chip types, therefore I guess they share a common ATU register layout.
More testing would be appreciated.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46379
To improve reproducibility, prevent the inclusion of timestamps
in the gzip header.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 46361
The mips reloc patch introduced new allocations which were done before
add_unformed_module but never freed them in case of an error. A new hook in
Linux 3.19 called module_arch_freeing_init can be used for freeing memory
which were allocated during this init phase.
The problem can be seen when trying to load a module (via busybox insmod)
when it was already loaded.
free -m
for i in `seq 1 100`; do
/sbin/insmod /lib/modules/*/ath9k.ko >& /dev/null
done
free -m
This simple loop would leak ~3.2 MB.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46247
Backport for the Spansion S25FL164K
It's a 8 MiB flash chip with 4 KiB erase sectors.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46237
This is useful if the device also has an ethernet WAN interface with a
separate mac address (that is derived from the LAN mac address).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46220
Some machtypes were dropped when 4.0 support was added, and the
incomplete patch was taken over to 4.1.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46187
