Commit graph

46 commits

Author SHA1 Message Date
Christian Lamparter
82618062cf ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617

Hardware highlights:

SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR:    32 MiB Macronix MX25L25635F
ETH:    Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:    1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS:   Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS

Serial:
	WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
	The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
	pre-soldered. Pinout:
	  1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX

first install / debricking / restore stock:
 0. Have a PC running a tftp-server @ 192.168.1.99/24
 1. connect the PC to any LAN-Ports
 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
    into the tftp-server root directory and rename it to just "ras.bin".
 3. power-cycle the router and hold down the the WPS button (for 30sek)
 4. Wait (for a long time - the serial console provides some progress
    reports. The u-boot says it best: "Please be patient".
 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
    flashes fast at the same time. You have to reboot the device and
    it should then come right up.

Installation via Web-UI:
 0. Connect a PC to the powered-on router. It will assign your PC a
    IP-address via DHCP
 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
 2. Go to the "Expert Mode"
 3. Under "Maintenance", select "Firmware-Upgrade"
 4. Upload the OpenWRT factory image
 5. Wait for the Device to finish.
    It will reboot into OpenWRT without any additional actions needed.

To open the ZyXEL NBG6617:
 0. remove the four rubber feet glued on the backside
 1. remove the four philips screws and pry open the top cover
    (by applying force between the plastic top housing from the
    backside/lan-port side)

Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|   Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

|NBG6617> HELP
|ATEN    x[,y]     set BootExtension Debug Flag (y=password)
|ATSE    x         show the seed of password generator
|ATSH              dump manufacturer related data in ROM
|ATRT    [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO              boot up whole system
|ATUR    x         upgrade RAS image (filename)
|NBG6617>

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

|NBG6617> ATSE NBG6617
|012345678901

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711

copy and paste the result into the shell to unlock zloader.

|NBG6617> ATEN 1,0046B0017430

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

|NBG6617> ATGU
|NBG6617#

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-26 08:57:26 +02:00
Hannu Nyman
dcfe2a461e include/image-commands.mk: shorter version in Netgear factory header
Shorten the version string in Netgear factory image header in order
to enable u-boot TFTP recovery flash mode to work again.

Strip 'r7210-14cb05909a' into 'r7210' in the Netgear image header
by removing the hash (anything after "-").

background:
Some Netgear routers have recently been unable to flash Openwrt
factory image with the TFTP recovery flash mode provided by Netgear
u-boot. That is due to over-long Openwrt version string overflowing
into the router type string in u-boot code. Modern git versions
produce 10-digit short hashes for the Openwrt main repo, and that
causes the version string to be too long in the image header,
breaking the image ID verification by the TFTP flash routine.

(Other option could be to force a shorter hash in scripts/getver.sh,
but as the problem only concerns Netgear routers, let's patch just
them.)

More detailed explanations in FS#1583

Tested with WNDR3800

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-06-18 20:29:37 +02:00
David Bauer
399495a952 build: add apend-uboot command
This commit adds an append-uboot command to append U-Boot from the
bin-directory.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-22 20:34:14 +02:00
Mathew McBride
fba168f574 build: use busybox gzip compatible force option
commit 138c763 ("build: add --force option to gzip in Build/gzip")
added the --force flag to the gzip invocation.

Under environments with busybox gzip (e.g Alpine Linux), this fails
as busybox only recognizes "-f".

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-05-21 18:07:48 +02:00
Mathias Kresin
74a0d8cd92 build: consolidate fake uImage header build commands
Merge the two existing functions and use a parameter for the type
header field.

It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-20 20:58:52 +02:00
Mathias Kresin
38bd4e4eb5 build: fix uImage fake header command
Use a syntax compatible with mkimage from u-boot 2018.03 to fix the
build errors spotted by the build bot.

The images are binary identical to the ones generated with mkimage from
u-boot 2014.10.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-19 19:15:00 +02:00
Sven Eckelmann
1b773a46c2 build: Allow to change the FIT config section name
Some devices only boot when a special config is found in the image and
completely ignore the default entry during the selection. These devices can
now use the variable DEVICE_DTS_CONFIG in their device image definition.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2018-03-17 08:09:04 +01:00
Stijn Tintel
138c76332b build: add --force option to gzip in Build/gzip
When using pigz, a parallel gzip implementation, the gzip step in the
image build for some targets fails, because the image filename already
has the .gz extension. This results in an emtpy image file. Fix this by
adding the --force option to gzip in the Build/gzip macro.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Martin Schleier <drahemmaps@gmx.net>
2018-02-19 23:54:38 +01:00
Jo-Philipp Wich
b9aca834e8 at91: fix image building with CONFIG_TARGET_MULTI_PROFILE
The current image build code has a number of race conditions and interface
contract violations in the custom image build steps:

 - Build/install-zImage, solely used by at91, relies on $(PROFILE_SANITIZED)
   which is not available when building with CONFIG_TARGET_MULTI_PROFILE

 - Build/at91-sdcard, which may run concurrently, creates scratch files at
   fixed locations and manipulates target files directly which can lead
   to file corruption and other unexpected failures

Rename the install-zImage macro to at91-install-zImage and move it to the
at91 image Makefile since this target is the sole user. Also utilize "$@"
as output file name and switch the usage of $(PROFILE_SANITIZED) to
$(DEVICE_NAME) in order to fix naming under multi profile builds.

Fix the at91-sdcard macro to construct scratch file paths relative to "$@",
which is guaranteed to be unique and store the final artifact output in "$@"
as well, instead of inside $(BIN_DIR). The generic image build code takes
care of moving a build steps "$@" output to the final destination in a
concurrency-safe manner.

Finally remove the broken install-zImage from the generic image-commands
Makefile.

Fixes: d7a679a036 ("at91: Install zImage.")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-02-14 15:47:16 +01:00
Felix Fietkau
cde71a543c build: replace uses of OpenWrt with $(VERSION_DIST)
This makes the distribution name more configurable.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:15:53 +01:00
Sven Eckelmann
a28bf67c26 build: add image command for CE images
Combined Extended Images V1 can be created easily via the new image
commands using

    IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | combined-ext-image

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 07:58:47 +01:00
Zoltan HERPAI
7b5c989ab9 merge: targets: update image generation and targets
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2017-12-08 19:41:18 +01:00
Felix Fietkau
e23ff063d3 build: avoid failing in append-metadata if image could not be generated
The image build might have failed due to a size check

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-12-04 20:24:51 +01:00
Felix Fietkau
986d9deb3b build: allow calling append-dtb from image build commands
mpc85xx uses this for firmware image files, since the dtb data is not
directly part of the kernel image. This causes build failures in the
image builder.

Fix this by adding a separate build step that runs this call earlier,
reusing the generated file for any calls from kernel or image build
commands.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-02 16:01:18 +01:00
Alexander Couzens
49b84624eb image-commands: tplink-v2-header: pass kernel loadaddr and entry
Initramfs images won't boot if the default loadaddr and entrypont is
different.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-10-09 16:10:05 +02:00
Thibaut VARÈNE
254061ee97 build: add mktplinkfw2 hardcoded values to makefile
This patch adds all the board-specific values currently hardcoded
in mktplinkfw2.c back to the respective device declarations in the
makefiles.

The rationale is to avoid modifying the source code every time a
new board or board variant is added.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2017-10-06 08:28:41 +02:00
Sandeep Sheriker Mallikarjun
feb1907270 build: add image command for installing zImage file.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2017-09-20 09:00:25 +02:00
Piotr Dymacz
f08f754993 build: move mktplinkfw-combined command to image-commands.mk
We will need "mktplinkfw-combined" command also in the "ramips" target
for new MediaTek based TP-Link devices, with "safeloader" image type.

Also, rename the command to "tplink-v1-header", use "VERSION_DIST"
variable instead of "OpenWrt" and allow passing additional parameters.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:29:50 +02:00
Piotr Dymacz
5b7f592251 build: move mktplinkfw2 related commands to image-commands.mk
There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
7d6c63d875 build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Mathias Kresin
e7cd6f5d66 ar71xx: add AVM FRITZ!WLAN Repeater 300E support
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)

To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin
8e0d7d6574 build: move lzma2eva build step to image-commands.mk
Move it to image-commands.mk so that it can used by other targets with
eva based boards as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Joseph C. Lehner
2c2fc50d06 build: make NETGEAR_REGION optional in netgear-chk
This patch makes specifying NETGEAR_REGION optional, in which case
mkchkimage will default to region 1 (WW).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-03-12 09:28:19 +01:00
Thomas Reifferscheid
1d49b534f5 build: unsilence move command
The @ sign in front of the "mv" command was significantly suppressing
output to stdout. When reviewing the make/build logs it was tricking
me a whole lot and it mad me lose time. Removing the @ sign will get
stdout and logs right about what happened when.

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-02-22 22:52:20 +01:00
Joseph C. Lehner
7d00cfe9bb build: centralize fakeroot code
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.

Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
FUKAUMI Naoki
7faee1bc9f firmware-utils: improve tools for Buffalo DHP series
some of Buffalo DHP series use slightly different trx magic, buffalo-enc,
buffalo-tag, and factory image begin with 'bgn'.

this patch adds support for building those images.

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2017-01-31 10:55:02 +01:00
Joseph C. Lehner
aeba0fe466 build: move append-file to image-commands.mk
Move it append-file to image-commands.mk so that it can used by other
targets as well.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-01-27 11:10:10 +01:00
Ian Pozella
859693509f image.mk: use LINUX_KARCH rather than ARCH for mkits
The generated 'its' is passed to mkimage which expects linux arch
strings rather than the full arch (e.g. mips not mipsel).

It currently works in some cases where LINUX_KARCH == ARCH but
otherwise you get an unknown arch build error.

Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 14:54:11 +01:00
Felix Fietkau
c2e6ca26e5 build: add image command for calling kernel2minor
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-07 17:50:54 +01:00
Felix Fietkau
77265e00c7 build: add support code for appending metadata to images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
Mathias Kresin
61c2a7339a image: remove padding parameter from append-kernel/append-rootfs
Using pad-to instead of passing the optional padding to append-kernel
or append-rootfs. It could be that the value of a variable is passed.
In case the variable is empty no error is thrown.

Furthermore the purpose of the extra parameter is hard to get without
reading the code.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-13 19:36:41 +02:00
Felix Fietkau
d2a7df0792 octeon: use new ext4/f2fs overlay support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Mathias Kresin
ddd259b0d5 image: pass device blocksize to padjffs2
At the moment the padding steps are hardcoded. Especially images for
devices with a 4K sector size can be unnecessarily bloated using the
hardcoded padding steps.

It has been observed that 192Kb of padding was added to the image of a
4MB device, albeit due to the 4K sector size the minimum required extra
padding for the jffs2 rootfs_data is 20Kb.

In worst case it means that the image-size check could fail albeit
there is enough space for all selected packages

For device build code not exposing the blocksize, use the hardcoded
padding further on.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 07:40:15 +02:00
Mathias Kresin
3e7524c184 image: add support for k unit suffix to append-ubi
Allows to use the same unit for all definitions of the blocksize to be
consistent regardless of the used filesystem.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 08:51:58 +02:00
Mathias Kresin
b99a93ebaf image: add support for k unit suffix to pad-offset
Allows to specificy the padding and offset in kilobytes to be
consistent with pad-to.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 07:36:12 +02:00
Felix Fietkau
a84a74f618 scripts/ubinize-image.sh: add support for adding custom partitions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-31 13:05:19 +02:00
John Crispin
4df2011794 include/image.mk: allow image code to override uImage name
Signed-off-by: John Crispin <john@phrozen.org>
2016-08-03 15:30:13 +02:00
Felix Fietkau
94dec60d75 build: add template for installing device .dtb files
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-31 19:35:05 +02:00
Felix Fietkau
63b525dd6b image: add a helper variable for getting kernel/rootfs from within image Build/* templates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-31 12:25:25 +02:00
Felix Fietkau
84718d8736 image: add support for overriding kernel/rootfs images in sysupgrade-tar template
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-30 14:10:33 +02:00
Jo-Philipp Wich
db49dd894e build: rename sysupgrade-nand to sysupgrade-tar
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-29 16:53:03 +02:00
Felix Fietkau
9a50a213d2 image.mk: add support for specifying the VID header offset for UBI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau
7bdc21de72 image.mk: fix append-dtb race when multiple devices use the same .dts
Call Image/BuildDTB unconditionally to keep things consistent

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-15 14:18:14 +02:00
Felix Fietkau
b8fddb8912 image: allow devices to override the -E 5 ubinize option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-14 10:27:30 +02:00
Ben Whitten
b7baaaf782 kernel: Move append-dtb to common image-commands
This build step is used by various targets, move it to a common section.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
2016-06-22 19:32:06 +02:00
Felix Fietkau
4c33bbf8f4 image.mk: split off all Build/* commands into image-commands.mk
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-07 08:58:40 +02:00