reorder some parts of the patch to remove the declaration-after-
statement warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46205
Current firmware should work for station mode as well, and the older
firmware will usually behave worse and become unsupported over time.
Also, the MAC address handling on ar71xx is only implemented on one
firmware version.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46197
This firmware adds support for management frames over normal
packet transport interface instead of over the WMI management
interface.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46195
sd_mod depends on scsi_mod, but due to it being an AutoLoad and not
AutoProbe module, it was not loading when installing the package,
causing unknown symbol errors for sd_mod and anything depending on it.
Closes#14927, #18293, #19351.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46176
We were not copying the additional files needed to get USB to work on
the AT91 platforms, make sure we do this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 46172
A long time ago, ath9k had issues during reset where the DMA engine
would stay active and could potentially corrupt memory.
To debug those issues, the driver would print warnings whenever they
occur.
Nowadays, these issues are gone and the primary cause of these messages
is if the MAC is stuck during reset or busy processing a long
transmission. This is fairly harmless, yet these messages continue to
worry users.
To reduce the number of bogus bug reports, turn these messages into
debug messages and count their occurence in the "reset" debugfs file.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46158
A duplicate include guard prevents inclusion of barrier.h in UML build and this prevents mac80211 from building.
This patch re-enables mac80211 hwsim and renames the include guard.
See https://lists.openwrt.org/pipermail/openwrt-devel/2015-June/033614.html for details.
Signed-off-by: Martin Tippmann <martin.tippmann@gmail.com>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 46133
Boot tested: http://pastebin.com/L6aAb9xj
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo:
update to 4.1 final
add patches added since submission
delete patches applied in later rcs
restore commit messages in 220-gc-sections and 304-mips_disable_fpu
fix 050-backport_netfilter_rtcache to match new API
update inlined dma ops with upstream changes
add missing config symbols
enabled CONFIG_MULTIUSER
update kmod defintions for 4.1
]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46112
There are two important patches in this patchset: updating read pointer
quicker & rework of .get_station().
There are few more upstream patches that are p2p-related and weren't
backported in this commit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46084
This fixes some build problems with musl. The binary only program
nas.exe wants to link against __assert, which is copied from uClibc.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46021
On bcm53xx we still need usb-ohci to support USB 1.1 devices and it
obviously needs bcma-hcd.ko that will init controller and register
platform device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45994
This one cannot possibly work, as it depends on cfg80211, which is built
out of tree.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45985
This allows e.g. BCM43602 to work out of box, without dumping a proper
MTD partition to /lib/firmware/ NVRAM file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45931
They are useless, as the platform already selects the right options for
NAND support. The main reason for removing them is the fact that it
makes kernel configs more annoying to maintain on platforms that provide
NAND drivers but disable them (e.g. ramips)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45919
These are two new packet schedulers introduced in Linux 3.12 and 3.14
respectively. sch_fq is a perfect fairness queueing scheduler that also
adds pacing on host TCP flows, and sch_pie is an AQM.
Having them available in kmod-sched makes it easier for people to test
these new queueing schemes.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
SVN-Revision: 45885
We just moved the stmmac support in the kernel for ipq806x. Therefore,
nobody needs this driver so we'll just get rid of it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45872
Add dependency of kmod-crypto-ecb to kmod-bluetooth to avoid the kernel warning
"Bluetooth: Unable to create crypto context".
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 45860
Before starting hostapd we create interface for it. The problem is we
try to create STA interface just to let hostapd change it to AP later.
It may fail if device doesn't support STA interfaces or if we already
hit a limit. Consider following phy (it's from BCM43602 and brcmfmac):
$ iw phy phy0 info | tail
valid interface combinations:
* #{ IBSS, managed } <= 1, #{ AP } <= 4, #{ P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
total <= 3, #channels <= 1
Trying to setup 2 interfaces: STA + AP results in:
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): Configuration file: /var/run/hostapd-phy0.conf
radio0 (1101): Could not read interface wlan0-1 flags: No such device
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45856
nss-gmac has been replaced by its upstream counterpart "stmmac", to
which we added the SoC glue layer required for it to run on IPQ806x.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45832
This fixes various problems with parsing platform NVRAM. It's required
to get BCM43602 working in most cases.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45802
modules relating to CONFIG_USB_AUDIO
Kernel <2.6.35 is not supported in trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45734
3.18.12 backported 61ada528dea028331e99e8ceaed87c683ad25de2 ("sched/wait:
Provide infrastructure to deal with nested blocking") from 3.19, causing
the following error on load:
[ 13.588000] compat: exports duplicate symbol woken_wake_function (owned by kernel)
Fix this by guarding it with a check for 3.18.11 or earlier instead of
3.19.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45710
Before r45593 kmod-l2tp-ip did not depend on kmod-ipv6.
With r45593 support for L2TP IPv6 encapsulation was added and
included in the kmod-l2tp-ip package. This change also
added the dependency to kmod-ipv6 to kmod-l2tp-ip, regardless
of whether the user chose to generally include IPv6 support
or not.
Change this so L2TP over IPv6 and the resulting dependency
to kmod-ipv6 is only included in kmod-l2tp-ip if IPv6 support
is enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45612
instead of failing when authsae is not installed, also try using
wpa_supplicant as the newly added -mesh variants support mesh mode
and SAE encryption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45520
it has been non-functional for years and caused numerous memleaks and
crashes for people that tried to enable it.
it has no maintained upstream source, and it does not look like it's
going to be fixed any time soon
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45423
Two errors "netifd: radio0: sh: bad number" have recently surfaced in system
log in trunk when wifi interfaces come up. I tracked the errors to checking
numerical values of some config options without ensuring that the option has
any value.
The errors I see have apparently been introduced by r45051 (ieee80211r in
hostapd) and r45326 (start_disabled in mac80211). My patches fix two
instances of "bad number", but there may be a third one, as the original
report in bug 19345 pre-dates r45326 and already has two "bad number" errors
for radio0.
https://dev.openwrt.org/ticket/19345
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45379
Fixes build failure caught by buildbot:
IEEE Std 802.15.4 Low-Rate Wireless Personal Area Networks support (IEEE802154) [M/n/y/?] m
6lowpan support over IEEE 802.15.4 (IEEE802154_6LOWPAN) [N/m/?] (NEW) aborted!
Console input/output is redirected. Run 'make oldconfig' to update configuration.
make[6]: *** [silentoldconfig] Error 1
make[5]: *** [silentoldconfig] Error 2
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45357
- move config symbol to separate package (Why was it there in the first place?)
- 8723au might be used in some USB sticks or on some sunxi boards
compile tested only
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45336
Subtarget legacy is supposed to support all ssb SoC except for BCM4705.
There are few BCM4703 devices with 802.11n supprt (WRT160N v1.0, v1.1).
Few BCM4704 devices with 802.11n: ASUS WL-500W, Linksys WRT150N v1.0 &
v1.1, Linksys WRT300N v1.0, Netgear WNDR3300 v1, WNR834B v1 & v2.
It seems we have to enable N-PHY for legacy as well to support above.
Unfortunately it increases root.squashfs size by 48 460 B.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45309
