Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49280
Use the same name for TP-Link images as it was with the old image build
code.
Move the BOARD_ID export to the TP-Link image build recipe, to indicate
that the variable is only related in this context.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49279
Based on the vg3503j_gphy_led.sh script published in the VG3503J wiki
article, the OEM Firmware uses the following PHY led functionality:
gphy led 0: LINK/ACTIVITY
gphy led 1: LINK
gphy led 2: ACTIVITY
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49278
The VGV7510KW22 has the leds for LAN1-3 connected to pin1 of the phys
and the led for LAN4 connect to pin0 of the phy. This results with the
current configuration in a fast flashing LAN4 led as soon as a network
cable is connected. Something similar was reported on the forum[1] for
the VGV7519 as well.
Since it isn't predicable to which pin a (single) phy led is connected,
use the (default) pin1 functionality
Constant On: 10/100/1000MBit
Blink Fast: None
Blink Slow: None
Pulse: TX/RX
for all ethernet phy leds.
After checking pictures of all vr9 boards, it looks like only the VG3503J
has more than one led connected per phy. Using the phy led device tree
bindings to assign the functionality to the "additional" leds, the
VG3503J phy leds should behave as before.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
[1] https://forum.openwrt.org/viewtopic.php?pid=321523
SVN-Revision: 49270
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49268
So far fixtrx was calculating checksum over amount of data matching
partition erase size. It was mostly a workaround of checksum problem
after changing anything in initial TRX content (e.g. formatting JFFS2).
Its main purpose was to make bootloader accept modified TRX. This didn't
provide much protection of flash data against corruption.
This new option lets caller request calculating checksum over a bigger
amount of data. It may be used e.g. to include whole kernel data for
checksum and hopefully make bootloader go info failsafe mode if
something goes wrong.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
We plan to adjust usage of the main buffer to allow reading custom
amount of data for CRC32. This means we need another buffer that will be
always block aligned.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
1) Put sanity checks in one place
2) Respect provided offset
3) Read only as much data as needed for MD5 calculation
Thanks to the last change this is a great speedup and memory saver. On
devices with NAND flash we were allocating & reading about 128 MiB while
something about 8 MiB is enough.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
This avoid long (and unneeded) process of reading all data in case of
running on MTD not containig Seama entity.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
On platforms supporting both: TRX and Seama calling "fixtrx" was
resulting in trying to fix Seama as well.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Building for octeon fails with
'arch/mips/vdso/vdso-o32.so.dbg' already contains a '.MIPS.abiflags'
section
if the file already exists from a prior build.
Use the same workaround as the one for vdso.so.dbg committed in
9eb155353a.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Fixes the following error:
gdate.c: In function ‘g_date_strftime’:
gdate.c:2497:7: error: format not a string literal, format string not checked [-Werror=format-nonliteral]
tmplen = strftime (tmpbuf, tmpbufsize, locale_format, &tm);
^~~~~~
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Packages may install scripts into /etc/uci-defaults to be executed once
after installation, usually at the first boot of the target. This works
fine if the package was installed to the rootfs during build or using
the ImageBuilder.
If the package is installed using opkg during run-time uci-defaults
were applied only after a reboot of the device. Avoid the need to
reboot by evaluting the package's uci-defaults in default-postinst.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Bump to the latest version, fixes several security issues:
* CVE-2016-2107, CVE-2016-2105, CVE-2016-2106, CVE-2016-2109, CVE-2016-2176
More details at https://www.openssl.org/news/openssl-1.0.2-notes.html
Signed-off-by: Michal Hrusecky <Michal.Hrusecky@nic.cz>
Update to latest HEAD in order to fix MARK rule generation for local traffic,
also fix a possible race condition during firewall start.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch adds missing ASCII aliases to the libiconv stub in order to avoid conversion errors like https://github.com/openwrt/packages/issues/2373
Signed-off-by: Gergely Kiss <mail.gery@gmail.com>
Patch Lua packet script defines SHRT_MAX which is already defined in <linux/kernel.h> and
is included indirectly by lauxlib.h. Fix the redefintion as it leads to compile failure
on systems which treat macro redefinition as an error
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Remove the public unatteded buildkey from the opkg package to avoid
having hardcoded keys in tree. Use the external keyring package instead
which can be easily updated by users.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Currently the build fails with
'arch/mips/vdso/vdso.so.dbg' already contains a '.MIPS.abiflags' section
if the file already exists from a prior build.
Add a makefile rule to force the rebuild of vdso.so.dbg if genvdso has
has been changed to workaround the failure.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
