Add support for 3.13 as a development kernel. Mostly untested, only net
booted. If flashed may brick your router or kill your cat.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39746
Let the switch start the carrier and set the duplex mode independently
if this nic is up of not.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39733
We did not start the PHY when an external phy was in use. Without this
patch the driver uses half duplex mode and the switch uses full duplex
mode, which causes problems.
Thank you fback for spotting this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39719
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.
Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39703
That will be used to drive the 74HC595 serial-in/parallel-out
8-bits shift register which can be found on some RouterBOARDs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39702
The serial flash devices used on the ROuterBOARDs are
supporting 4KiB erase blocks. Enable the small sector
erase option in the m25p80 driver to avoid superfluous
erase/write of adjacent blocks.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39696
This is a backported patch for the gianfar ethernet driver
used in TPLink 4900 v1. It is supposed to fix the error which
show up in dmesg with:
NETDEV WATCHDOG: eth0 (fsl-gianfar): transmit queue xy timed out
Full upstream patch is at: http://patchwork.ozlabs.org/patch/271242
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
SVN-Revision: 39692
Only netboot tested, so no images or now.
GbE ports are only working in FE mode, and leds do not work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39679
Completely untested except for booting from network; wan port
only works in 10/HD, lan1 only in 100/FD.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39678
BCM63168 has 6 ports (3 FE PHY, 1 GE PHY, two RGMII) and BCM63268
has two additional RGMII ports, making it 8.
Fix this by checking the chip variant and applying an appropriate
limit.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39677
Support for Asmax AR 1004g router
Signed-off-by: Adrian Feliks <mexit@o2.pl>
Patchwork: http://patchwork.openwrt.org/patch/4464/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39674
This adds profile and build image for Sagemcom F@st2704, using b43
driver.
For WiFi to work properly BCMA fallback SPROM support patch must
be applied (http://git.io/z1Ki8A).
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4212/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39673
This adds userspace support for Sagemcom F@st 2704 router.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4215/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39672
This adds kernel support support for Sagemcom F@st 2704 wireless ADSL
router.
It's a BCM6328-based 802.11n wireless router with USB port and ADSL2+
modem equipped with 64 MiB RAM and 8 MiB flash.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4266/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39671
Update the Ventana device-tree to match upstream:
- Add IMX6Q/IMX6DL variants for GW54xx/GW53xx/GW52xx/GW51xx
- align pinctrl with upstream
- consolidate multiple patches into one
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39644
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result. I have cleaned up this patch.
When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.
This patch applies cleanly to SVN 39392.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
- drop the 'rb951ui_wlan_init' function and rework the code to
use the recently introduced rb95x_wlan_init function instead,
- fix GPIO number of the port5 LED,
- rename LEDs according to the standard LED naming conventions,
and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39641
This is a backport of code to improve the quality of fq_codel
hashing for 3.10 for some encapsulated protocols.
Not needed in 3.11 and later.
Patch-by: Dave Taht <dave.taht@bufferbloat.net>
Patchwork: http://patchwork.openwrt.org/patch/4902/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39640
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4849/
[juhosg:
- use the Archer C7 specific LED setup instead of adding
identical code]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39636
This missing bit of the hack saves hugely on instruction traps
on tcp connections to ar71xx based routers.
Patch-by: Dave Taht <dave.taht@bufferbloat.net>
Patchwork: http://patchwork.openwrt.org/patch/4905/
[juhosg: adjust subject, refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39626
Solves ticket #14356 <https://dev.openwrt.org/ticket/14356>
Without this patch, UART output will show only 4 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000050000 : "u-boot"
[ 0.760000] 0x000000050000-0x000000070000 : "u-boot-env"
[ 0.770000] 0x000000070000-0x0000007f0000 : "firmware"
[ 0.790000] 0x0000007f0000-0x000000800000 : "art"
and then linux complains :VFS: Cannot open root device "(null)"
With this patch, UART out will show 7 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.760000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.770000] 0x000000050000-0x0000007f0000 : "firmware"
[ 0.780000] 2 netgear-fw partitions found on MTD device firmware
[ 0.780000] 0x000000050000-0x00000014b440 : "kernel"
[ 0.790000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.800000] 0x00000014b440-0x0000007f0000 : "rootfs"
[ 0.810000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.820000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.830000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.830000] 0x000000340000-0x0000007f0000 : "rootfs_data"
[ 0.840000] 0x0000007f0000-0x000000800000 : "art"
This patch is tested against r39502 of trunk.
Signed-off-by: Jonathan Chang <changcs@santos.ee.ntu.edu.tw>
Patchwork: http://patchwork.openwrt.org/patch/4870/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39625
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0xfe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-dockstar-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-by: Alexander Couzens <lynxis@fe80.eu>
CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39593
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0xfe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-ib62x0-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-by: Luka Perkov <luka@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39592
Previous patch was pushed due to false user report. While at it fix alphabetic
ordering.
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0x1fe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-iconnect-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39591
Some ARV4510PW units seem to have unstable PCI due to missing pull-up
resistors. This patch makes sure that the GPIO lines are driven properly.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 39587
The mtdpartsize macro triggers shell errors on various Linux distributions
when the partname argument $(1) does not appear within the partmap $(2).
Change the sed pattern to only emit anything if a successful substitution
occured and only evaluate the arithmetic expression if something was printed
by the sed program.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39583
This Armada XP GP board from Marvell comes with:
* 2GB DDR3 DIMM
* 1GB NAND flash (8-bit interface)
* 16MB NOR flash (16-bot interrface)
* 16MB SPI flash
* SDIO module
* 3 PCIe
* 1 SATA link
* 2 USB EHCI
* 1 internal SSD
* 4 Ethernet Gigabit
* 1 RS232 port over USB
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com>
SVN-Revision: 39568
The config-3.10 doesn't specify the configuration of the backported PCI
features, and the Marvell EBU Device Bus Controller, this will prevent
a clean compile. This patch enables these features to archive a clean compile
without having to specify the state of these configuration after starting to
compile.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com>
SVN-Revision: 39567
This is a backport of the patches accepted to the Linux mainline related to
mvebu SoC (Armada XP and Armada 370) between Linux v3.12, and Linux v3.13.
This work mainly covers:
* Finishes work for sharing the pxa nand driver(drivers/mtd/nand/pxa3xx_nand.c)
between the PXA family, and the Armada family.
* timer initialization update, and access function for the Armada family.
* Generic IRQ handling backporting.
* Some bug fixes.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com>
CC: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39566
This is a backport of the patches accepted to the Linux mainline related to
mvebu SoC (Armada XP and Armada 370) between Linux v3.11, and Linux v3.12.
This work mainly covers:
* Ground work for sharing the pxa nand driver(drivers/mtd/nand/pxa3xx_nand.c)
between the PXA family,and the Armada family.
* Further updates to the mvebu MBus.
* Work and ground work for enabling MSI on the Armada family.
* some phy / mdio bus initialization related work.
* Device tree binding documentation update.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com>
CC: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39565
This is a backport of the patches accepted to the Linux mainline related to
mvebu SoC (Armada XP and Armada 370) between Linux v3.10, and Linux v3.11.
This work mainly covers:
* Enabling USB storage, and PCI to mvebu_defconfig.
* Add support for NOR flash.
* Some PCI device tree related updates, and bus parsing.
* Adding Armada XP & 370 PCI driver, and update some clock gating
specifics.
* Introduce Marvell EBU Device Bus driver.
* Enaling USB in the armada*.dts.
* Enabling, and updating the mvebu-mbus.
* Some SATA and Ethernet related fixes.
Signed-off-by: Seif Mazareeb <seif.mazareeb@gmail.com>
CC: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39564
smsc95xx.ko depends on crc16.ko on kernel >= 3.8
There was an additional kmod-usb-net-smsc95xx definition in the mxs
target code which conflicted with the one in the common area.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39562
