It corresponds to the following example in dnsmasq.conf.example:
# Always set the name of the host with hardware address
# 11:22:33:44:55:66 to be "fred"
#dhcp-host=11:22:33:44:55:66,fred
Regards
Mathias
SVN-Revision: 26983
broadcom-wl driver bound to ssb device with ssb driver probe
have osh handle struct pdev pointer value initialized with
ssb_device pointer. Later on pdev is used with legacy pci
dma api as pci_dev thus causing oops sometimes.
The patch replaces legacy pci dma api and pass relevant
device struct pointer to avoid crashes.
Signed-off-by: George Kashperko <george@znau.edu.ua>
SVN-Revision: 26949
the attached patch makes ipcalc.sh accept IP/Netmask combinations in
CIDR notation. Before you could only do:
# sh ipcalc.sh 192.168.0.0 255.255.255.0 1 10
IP=192.168.0.0
NETMASK=255.255.255.0
BROADCAST=192.168.0.255
NETWORK=192.168.0.0
PREFIX=24
START=192.168.0.1
END=192.168.0.11
with this patch you can also execute it with:
sh ipcalc.sh 192.168.0.0/24 1 10
IP=192.168.0.0
NETMASK=255.255.255.0
BROADCAST=192.168.0.255
NETWORK=192.168.0.0
PREFIX=24
START=192.168.0.1
END=192.168.0.11
The patch is based on #1260 [1], i just changed one line to calculate
the START end END ips right. I wonder why that never got included. If
there is no reason not to do i would like to ask you to commit that
patch, because its a functionality i (and probably others) miss quite often.
Btw, i also fixed 4 useless tabs, that might look a bit strange in the
patch.
Regards, Manuel
SVN-Revision: 26930
Since the oldest kernel in trunk is 2.6.30 the modules always use the
newer names, so we can just use the _generic prefix directly.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26903
There's only 2.6, so it doesn't make sense to mention modules that are
2.4 only or for modules that they are available only for 2.6.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26902
With no 2.4 support in trunk, we can safely remove any 2.4 definitions for
kmods and merge the 2.6 definitions into the generic ones.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26901
Since there's only 2.6 in trunk $(KMOD_SUFFIX) can be safely replaced with
ko for all mainline kernel modules.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26900
NOTE: The KCONFIG associated with each of these modules gets selected
whenever CRYPTO_MANAGER (kmod-crypto-manager) is selected so these
modules are already being built.
Signed-off-by: Lars Hjersted <lars@hjersted.com>
SVN-Revision: 26812
(a) map the ssh service running on the firewall to 22001 externally, without modifying the configuration of the daemon itself. this allows port 22 on the WAN side to then be port-forwarded to a
LAN-based machine if desired, or if not, simply obscures the port from external attack.
(b) allow IPsec/ESP and ISAKMP (UDP-based key exchange) to happen by default. useful for most modern VPN clients you might have on your WAN.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 26805
If there is no sprom on an ssb based pci device on the brcm47xx
architecture ssb now asks the architecture code to look into the nvram
to get some sprom data for this device. Now we are able to read out
pci/1/1/ foo or pci/1/3/ foo config options.
This will fix some problems where the wireless devices does not got an
mac address and the following message was show:
ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
SVN-Revision: 26801
Fix compilation for 2.6.39 by replacing SPIN_LOCK_UNLOCKED with
DEFINE_SPINLOCK().
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26771
