Change some flow-level unctions to return with an
error code in order to be able to report errors
to the core code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38068
This patch adds support for TP-Link TL-MR13U router with built-in 10AH
rechargeable battery.
The patch is based on kamwanlai's patch:
https://forum.openwrt.org/viewtopic.php?pid=206746#p206746
Updated to accommodate recent changes introduced with:
ar71xx: remove fs_* variables from image/Makefile
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4063/
[juhosg:
- refresh and rename rename 930-add-tl-mr13u-support.patch =>
625-MIPS-ath79-add-tl-mr13u-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38063
This patch adds OpenWRT support for the Netgear WNR2200 (N300)
wireless router with USB.
Technical details of this router can be found at
http://www.netgear.com/home/products/wirelessrouters/work-and-play/WNR2200.aspx
and http://wikidevi.com/wiki/Netgear_WNR2200
Signed-off-by: Aidan Kissane <aidankissane@googlemail.com>
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4055/
[juhosg:
- add commit message and SoB line from the original patch
- remove dead code from mach-wnr2200.c
- refresh 624-MIPS-ath79-WNR2200-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38059
Add a new kernel config option for generic firmware partition
split support and change the uImage split support to depend on
the new option. Aslo rename the MTD_UIMAGE_SPLIT_NAME option to
MTD_SPLIT_FIRMWARE_NAME to make it more generic.
The patch is in preparation for multiple firmware format
support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38002
This patch adds support for building firmware images for the
TP-Link TL-MR3040 v2. Tested and working on v2.1 hardware.
Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37964
I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37963
When the squashfs and jffs2 images are generated
in the same turn, the compressed kernel images
are generated twice with the same parameters.
Move compressed kernel generation into a separate
phase to avoid that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37881
Those are not needed since we are generating the
initramfs images along with the others.
Remove the variables and use the template names
directly.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37876
Initramfs images are not generated for profiles which
are using the squashfs-only template. Add the missing
'Image/Build/Template/squashfs-only/initramfs' to fix
that.
Also, 'Image/Build/Cameo933x/initramfs' uses wrong
parameters for 'MkuImageLzma/initramfs' due to a
misplaced commma. Remove that to fix the generated
initramfs images.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37871
Apparently registering usb device on newest trunk causes
this AP not to boot...
Since there is no USB socket in that device anyway this
can be simply removed (and device boots then no problem).
[juhosg:
- tweak subject line and description,
- remove #include "dev-usb.h",
- remove 'select ATH79_DEV_USB' from Kconfig]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37844
Based on the original firmware, the file must have the tag
HORNET-PACKET-DIR505A1-3, not HORNET-RT-DIR505A1-3.
http://patchwork.openwrt.org/patch/3945/
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 37781
This patch fixes the code of the buttons for TP-Link WA901ND.
Signed-off-by: Rocco Folino <lordzen@autistici.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37696
Small router sold in EU: AR9330@400MHz, 1x USB2.0,
2x ethernet, 8MB flash, 32MB ram, one led, one button.
See: http://galeria.tech-blog.pl/TP-Link_TL-WR710N-EU/
[juhosg: use a separate kernel patch]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37572
Mercury MW4530R is a TP-Link TL-WDR4310 clone but
with a much lower price tag (~ $40). This patch
is tested to work at trunk r37525.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3856/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37571
Mercury MW4530R is a TP-Link TL-WDR4310 clone but
with a much lower price tag (~ $40). This patch
is tested to work at trunk r37525.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3856/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37570
Looks like trunk@37090 has changed the logic that determines
if router's button was pressed. This resulted in TEW632BRP
always booting into failsafe mode because it detected pressed
button (which was not pressed).
Measure with voltmeter has shown that buttons on this router
are actually active-low. This patch reflects this fact in
board configuration and fixes 'load info failsafe mode' issue.
Note: it looks like Trendnet TEW632BRP and a close relative
to TEW-652BRP V1.0 and D-Link DIR-615C1, so same problem may
exist on those routers as well. This patch doesn't affect
routers other than 632BRP and unfortunately I do not have
hardware to test this issue with other routers.
This patch fixes#13893 and is tested on actuall Trendnet
TEW632BRP.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37569
Create a separate board profile and update the profile
name in image/makefile. Also use the correct machtype
string in kernel command line.
Based on andelf's patch:
http://andelf.diandian.com/post/2013-05-22/40050677370
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37550
This reverts r37477. A generic patch is used to fix
this globally, so revert the ar71xx specific change.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37480
Drop the local get_mtd_part_size implementation and use
the equivalent function provided by lib/functions.sh.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37476
TL-WR941N v6 use almost same IC as WDR3500.
[juhosg: change subject, and change fw layout from 4M to 4Mlzma]
Patchwork: http://patchwork.openwrt.org/patch/3719/
Signed-off-by: ShuYu Wang <andelf@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37471
switch buttons should be declared as switch so the failsafe shell is not
triggered by accident in procd
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37131
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37049
The TP-LINK TL-MR3220 v2 has a button on the left side
labeled "WIFI". This is GPIO 24. This patch adds the
support for this button.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36848
The port 6 of the switch is connected to the SFP
cage on the RB2011*S boards. Add a helper function
to correctly initialize the switch configuration
data on those boards to make the SFP port usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36799
At offset 0x40, signature for TL-MR10U/TL-MR11U begin
from 0x00, not 0x10/0x11.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36727
MR10U is closer to MR3040 than WR703N. This changes also
enable USB power on GPIO18.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36726
This allow us to increase the kernel partition size,
and ensures, that the -factory image still usable via
the original interface.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36584
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36580
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36579
Here is corrected version (only thing not working are wifi LEDs).
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36578
