OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
- tested on Beagleboard C4
- remove upstream patches
- disable THUMB mode on OMAP3 this increases binary size
(remove CONFIG_SYS_THUMB_BUILD)
- reduce SPL size by disabling EXT feature
(remove CONFIG_SPL_EXT_SUPPORT)
this fixes 2015.07 and 2015.10-rc3
Beagleboard C4 booting
which were broken by upstream commit
with id: bd2c4522c26d535515aebca52d27c004a7e0c05c
Arm THUMB mode is broken because of an yet unknown errata
see: http://lists.denx.de/pipermail/u-boot/2015-August/225793.html
- backport upstream fix that was introduced in 2015.10-rc5
and was not fixed in 2015.10 final
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47924
gcc-5 handles inline without static differently and that makes
uboot-mxs fail to build. Remove the inline so it gets exported and can
be used in other functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47533
- Use board engineering names rather than marketing names
- Linksys uses a dual firmware layout, where the bootloader
will switch to the other stored image when one fails to
boot three consecutive times.
In order to make this firmware compatible with the factory
images and the stock bootloader we must match this layout.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47429
The current patch to add Duckbill support is wrong and does not
even compile. So replace this patch with a working one.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47007
Install uboot files to KERNEL_BUILD_DIR instead of BIN_DIR to fix
ImageBuilder. Similar fixes are necessary for many (all?) other uboot
targets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46605
Invert the `__GLIBC__` guards into `!__UCLIBC__` ones to avoid
invalid references to `_llseek` on musl.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46125
Add three download mirrors for 'grub', as the Makefile currently defines only
one download location.
@GNU can not be used, as the most recent version of 'grub' is not available
at the general GNU mirrors, and can only be found at the "gnu-alpha" mirrors.
Signed-off-by: Hannu Nyman <hannu.nyman at iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 45909
- kexec-tools is now distributed with tarballs of .tar.gz and .tar.xz
format; .tar.bz2 are not provided anymore.
- Add CONFIG_KEXEC_LZMA for selecting lzma support.
Patches are updated along to:
- Remove the now unnecessary patch 0004-mips_regdefs.patch.
- Drop 100-reduce_size.patch because the size reduction is marginal.
- Allow zlib and lzma support coexist together. This patch has been
merged into upstream project.
- Fix kexec-tools' configure.ac.
- Fix a few compilation warnings.
Size comparison of stripped binaries of kexec malta target with both
zlib and lzma support enabled.
- Before: 41447
- After: 42583
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44437
