Our code was assuming CPU port uses the highest number. My BCM53573
device has eth0 connected to port 8 and eth1 connected to port 5. While
working on support for it I tried to:
1) Enable all ports (including port 8)
2) Set CPU port to 5
I noticed port 8 is not accessible anymore. It was just a development
process but it seems like something worth fixing anyway.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
In kernel 4.7 there is upstreamed b53 driver using (mostly?) the same
symbols as our b53 does. Change our symbols so both drivers can coexist
in kernel tree.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
The swconfig kernel infrastructure fails to do any permissions checks when
changing settings. As such an ordinary user account on a device with a
switch can change switch settings without any special permissions.
Routers generally have few non-admin users so this isn't a big hole, but it
is a security hole. Likely the greatest danger is for multifunction devices
which have a lot of extra daemons, compromising a low-security daemon would
allow one to modify switch settings and cause the router/switch to appear to
lock-up (or cause other sorts of troublesome nyetwork behavior).
Implement a check for CAP_NET_ADMIN in swconfig_set_attr() and deny any
requests originating from user contexts lacking this capability.
Reported-by: Elliott Mitchell <ehem+openwrt@m5p.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Combine all bus operations for one MMD access in one function.
Protecting all these bus operations with one lock also helps
to avoid potential issues due to bus operations intercepting
the register and data write.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48914
The default TTL for address resolution table entries is 5 minutes
for all members of the AR8216 family. This can cause issues if
e.g. Wifi clients roam to another AP and their MAC appears on
another switch port suddenly. Then the client may not be reachable
until the old ARL entry expires.
I would have expected the switch to invalidate old entries if it
detects the same MAC on another port. But that's not the case.
Therefore make the TTL for ARL entries configurable.
The effective TTL will always be a multiple of 7 seconds.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48913
The line before includes the port number anyway so there's no need
to duplicate the port number in the MIB info header.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48912
The decimal values especially for TxByte and RxGoodByte are hard to read
once bigger amounts of data have been transferred.
Therefore complement the decimal values with info in GiB / MiB / KiB.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48911
For unused switch ports all MIB values are zero. Displaying ~40 empty
MIB counters is just confusing and makes it hard to read the output of
swconfig dev <dev> show.
Therefore, if all MIB counters for a port are zero, just display
an info that the MIB counters are empty.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48910
This patch adds speed_mask special file to LEDs connected to switch ports
via 'switch' trigger. It allows to choose which speeds to signal when link
is up. If router has more than one LED per port, they may light up
differently depending on how fast connection is. Default setting is 'all
speeds' so backward compatibility with system scripts (for example uci) is
maintained.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48775
This patch changes swconfig_trig_port_mask_store() handler to utilize
kstrtoul() function instead of call to obsolete simple_strtoul(). Thanks
to this change, new handler takes less memory and makes port_mask special
file accept not only hexadecimal, but also decimal and octal numbers.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48774
When dealing with Broadcom hardware we can simply use swconfig's generic
helper, we just need to do some validation of requested state.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48623
Thanks to this change swconfig can access port PHYs e.g. when setting
port link state with a generic helper.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48622
It's quite common for switches to have PHY per port so adding a generic
helper setting link state will help many drivers. It just needs an API
to access PHYs which this patch also adds.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48621
Directly return the return value of genl_register_family_with_ops()
instead of storing it in a temporary variable, then returning it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48472
BCM531x5 has two pontential cpu ports, and header mode can be enabled
independently on both.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48302
This add support for IGMP Snooping on atheros switches (disabled by default),
which avoids flooding the network with multicast data.
Tested on TL-WDR4300: disabling IGMP Snooping results in multicast flooding
on each specific port, enabling it back again prevents each port from
receiving all multicast packets.
Partially based on: http://patchwork.ozlabs.org/patch/418122/
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48268
Some switches can force link speed for a port. Let's add API that will
allow drivers to export this feature.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48142
As explained earlier, using SWITCH_TYPE_LINK gives more flexibility,
it doesn't require e.g. string parsing to read some data.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47999
So far we were sending link data as a string. It got some drawbacks:
1) Didn't allow writing clean user space apps reading link state. It was
needed to do some screen scraping.
2) Forced whole PORT_LINK communication to be string based. Adding
support for *setting* port link required passing string and parting
it in the kernel space.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47997
In r45970 the MAC swap handling was made opt-in, however some boards
have been forgotten during the conversion. Since the reference design
uses this MAC swapping, and pretty much all known boards using this chip
seem to do so too, enabling the swapping is a more reasonable default
than leaving it disabled.
Change the code to still allow boards to opt-out of this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47956
Kernel 3.14 added aditional genphy_soft_reset phy reset to phy_init_hw in drivers/net/phy/phy_device.c
Since adm6996 does in driver soft reset and doesn't use BMCR_RESET for soft reset
add dummy soft_reset callback to adm6996 driver, like it is done in ar8216.
This fixes ticket #20147
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47272
The previous "link" and "status" functions were non-standard,
and thus less useful for parsing.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 46864
This also clears any bootloader-set FDB defaults. This had
caused issues creating port-based VLANs when mappings
overlapped previous VLANs. Packets destined to a port
not in the default port group flooded all ports.
Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC)
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46699
If a link goes down, don't flush the complete ARL table.
Only flush the entries for the respective port.
Don't touch ARL table if a link goes up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46381
Adds functions for flushing ARL table entries per port.
Successfully tested on AR8327. Implementation for AR8216/AR8236/AR8316
is based on the AR8236 datasheet and assumes that the three chips
share a common ATU register layout.
Compile-tested only for AR8216/AR8236/AR8316.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46380
Adds the chip-specific part of reading ARL table for AR8216/AR8236/AR8316.
It's based on the AR8236 datasheet and compile-tested only as I couldn't
find datasheets for AR8216/AR8316 and don't own devices with these chips.
The existing ar8216_atu_flush implementation was used for all three
chip types, therefore I guess they share a common ATU register layout.
More testing would be appreciated.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46379
The position of the nvram header file on brcm47xx changed with kernel
version 4.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46170
On two tested devices: Netgear R6250 (BCM53011 rev 2) and Luxul XWC-1000
(BCM53011 rev 3) it was possible to use port 7 and eth1 (instead of port
5 and eth0). It seems BCM53011 just like BCM53012 has 8 ports and
usually 3 of them are connected to the SoC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46104
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
On device reset the sizes for the vlan and port tables were wrongly
calculated based on the pointer size instead of the struct size. This
causes buffer overruns on 64 bit targets, resulting in panics.
Fix this by dereferencing the pointers.
Reported-by: Fedor Konstantinov <blmink@mink.su>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45938
At least on my b53 chip, the mask is 3 bits wide, and because
of this some STP states are not set properly and discarded when read.
Maybe for some other chips it makes sense to have just 2 bits width,
but I don't have other versions around to test/validate.
If that's the case then maybe we could add another STP state mask.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45937
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45676
On BCM5301X there are two different cases to handle: CPU port 8 vs. any
other one. Support for CPU port 8 was already partially implemented but
it lacked setting some extra bit for 2G speed. It also will need to be
extended to implement "SMP dual core 3 GMAC setup". That's the reason
for handling it in separated code block.
This patch also adds overriding CPU port state for port other than 8. It
requires using recently defined GMII_PORT registers.
It was tested for regressions on BCM53011 revs 2 & 3. It was also
confirmed to fix switch on some internal Broadcom board.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45402
* properly enclose macro arguments in paranthesis on use
* remove trailing white space
* convert C99 // comments
* add missing blank lines after declaration
* remove braces from single statement blocks
* split lines > 80 chars (except for one)
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45356
It will now actually enable the mib counters instead of enabling rx/tx for
the first switch port.
Reported-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44788
For bcm63xx integrated switches, broadcom changed the data endianess
to match the system endianess. But this only applies to within one word,
which causes 48/64 bit values to be still split into their "litte endian"
groups.
E.g. 48 bit values (with 5 being the most significant byte) aligned
0x00 ..01 or 0123
0x04 2345 45..
will become
0x00 ..10 resp. 3210
0x04 5432 54..
Likewise for 64 bit values.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44568
drivers/net/phy/adm6996.c:881:5: warning: format '%lu' expects argument of type 'long unsigned int', but argument 5 has type 'u32' [-Wformat=]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44333
Add global read-only swconfig attribute "arl_table" to display the
address resolution table.
So far the chip-specific part is implemented for AR8327/AR8337 only
as I don't have the datasheets for the other AR8XXX chips.
Successfully tested on TL-WDR4300 (AR8327rev2)
and TL-WDR4900 (AR8327rev4).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44104
Until a few years ago the page switch wait time was set to msleep(1)
what was changed to usleep_range(1000, 2000) later.
I can not imagine that a low-level operation like switching page
on register level takes so much time.
Most likely the value of 1ms was initially set to check whether
it fixes an issue and then remained w/o further checking whether
also a smaller value would be sufficient.
Now the wait time is set to 5us and I successfully tested this on
AR8327. IMHO 5us should be plenty of time for all supported chips.
However I couldn't test this due to missing hardware.
If other chips should need a longer wait time we can add the
wait time as a parameter to the ar8xxx_chip struct.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44103
Check for switch port link changes and
- flush ATU in case of a change
- report link change via syslog
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44102
