Using PKG_SOURCE_DATE instead of PKG_VERSION will make the build system
generate the version based on the date and the git hash. This way the
tar file name changes when the git hash changes and this avoids problems
when someone forgets to change the version, but changes the git hash.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changes since last merge into OpenWrt since 2017-12-14:
- Added debugfs file tx_hist.
- Added debugfs file fixed_rate.
- Added debugfs file ba_hist.
- Modified the way to establish BA stream.
- Added code to control BF type.
- Added functions to check/dump dhcp packet.
- Upgrade 88W8964 firmware to 9.3.2.4.
- Added debugfs file coredump.
- Corrected the way to transmit multicast packets.
- Change driver version to 10.3.4.0-20180118.
- Corrected the way to get qos control.
- Assigned broadcast dhcpoffer to another queue.
- Separated broadcast and multicast packets. Bump to latest commit 20180206
Signed-off-by: Chris Breuer <github@chrisbreuer.de>
Make it easily possible to add a custom script in front of this hotplug
script which adds new devices. This is needed for the mvebu target in
which we want to migrate the old configuration before new devices are
getting detected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is currently possible to enable connlabel-support in iptables.
However, in order for connlabel to work properly, the kernel module must
also be present. This patch adds support for building the
connlabel-module, and selects it by default when connlabel-support is
enabled.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
For hardware that supports multiple h/w output queues, add
a compatible scheduler (NET_SCH_MULTIQ).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
The kmod-lp package included both lp.ko and ppdev.ko, but ECP device
drivers may or may not require lp NOT to be loaded, needing only ppdev.
Additionally, There were no packages for any parport interface modules,
such as uss720 or parport_pc, provided here. It has not been otherwise
possible to use PC-style parport hardware for kmod-lp.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
The last_rx field was removed from net_device. Since the field wasn't
used by the generic subsystem, and the driver only writes to it, just
remove the usage.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Once installed fou kernel module allows you to use FOU (Foo over UDP)
and GUE (Generic UDP encapsulation) tunnel protocols.
To get ip fou command working you also need to install ip-full.
Signed-off-by: Filip Moc <lede@moc6.cz>
3413961 mt7603: avoid reordering qos-null data packets
c60e6db mt76: toggle driver station powersave bit before notifying mac80211
246d548 mt76: stop tx queues from the driver callback instead of common code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The target it was meant for was updated to a version that this does not
compile with. It probably also hasn't been used in years
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ATM subsystem is different from the generic ethernet NICs. The ATM
subsystem requires a callback when a packet has been sent. It means a
tx skb_buff need to be used after it has sent. While the generic NIC
can fill up the TX ring and free skb_buffs if it encounter a ring buffer slot
with an already sent skbuff.
The ATM drivers need call the pop() function after it has send a
single ATM package. The ATM subsystem controls via this ways the queuing.
The ppe engine use DMA channels for read and write. Every atm_vcc has it's
own TX DMA channel and each TX DMA channel has it's own ring buffer.
The old driver had multiple issues:
- Call the subsystem callback at the beginning of tx function (ppe_send).
Didn't allowed the ATM subsystem to control the enqueued package
amount.
- Filled up the TX ring until full and fail futher
- copy or decouple the skb from all other subsystem before giving it
over to TX ring
The new tx path uses interupts.
- call the subsystem callback _after_ it was sent by hardware
- no need to copy our decouple the skb any more
- gives back control to the atm subsystem over the enqueued packages
- use an interupt for every sent atm package
Using interupts shouldn't be a problem because of the slow uplink bandwidth of
ADSL.
The speed _through_ the DSL router was always as high as it should
be, only traffic generated on the router itself were affected.
After changing to new tx path, the speed of iperf's run on the
router itself reached the same speed. The master/trunk wasn't as much
affected because of TCP optimisations (reboot-5022-gb2ea46fe236a).
The following results are taken on the remote server, which receives
the stream over the internet and the DSL line.
The sync moves between every sync a litte bit, but is so far stable
Latency / Interleave Delay: Down: Fast (0.25 ms) / Up: Fast (0.50 ms)
Data Rate: Down: 13.287 Mb/s / Up: 1.151 Mb/s
reboot-5521-g9f8d28285d without patch
[ ID] Interval Transfer Bandwidth Retr
[ 5] 0.00-10.04 sec 947 KBytes 773 Kbits/sec 0 sender
[ 5] 0.00-10.04 sec 928 KBytes 757 Kbits/sec receiver
reboot-5521-g9f8d28285d with patch
[ 5] 0.00-10.06 sec 1.16 MBytes 970 Kbits/sec 0 sender
[ 5] 0.00-10.06 sec 1.15 MBytes 959 Kbits/sec receiver
v17.01.4-239-g55c23e44f4 without patch
[ ID] Interval Transfer Bandwidth Retr
[ 5] 0.00-10.04 sec 87.4 KBytes 71.3 Kbits/sec 0 sender
[ 5] 0.00-10.04 sec 59.6 KBytes 48.7 Kbits/sec receiver
v17.01.4-239-g55c23e44f4 with patch
[ ID] Interval Transfer Bandwidth Retr
[ 5] 0.00-10.05 sec 1.18 MBytes 983 Kbits/sec 1 sender
[ 5] 0.00-10.05 sec 1.15 MBytes 959 Kbits/sec receiver
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2b7fae4 mt76: fix returnvar.cocci warnings
939e3e0 mt76x2: dfs: avoid tasklet scheduling during mt76x2_dfs_init_params()
cf59170 mt76x2: dfs: add set_domain handler
5e4d60e mt76x2: dfs: take into account dfs region in mt76x2_dfs_init_params()
f76e25f mt76x2: fix WMM parameter configuration
34d612d mt76: retry rx polling as long as there is budget left
0f8327a mt76x2: fix TSF value in probe responses
ad3f8e9 mt76: add an intermediate struct for rx status information
58a41f1 mt76: get station pointer by wcid and pass it to mac80211
b0508d3 mt76: implement A-MPDU rx reordering in the driver code
cf3cfc4 mt76: split mt76_rx_complete
461cdf9 mt76: pass the per-vif wcid to the core for multicast rx
9b2c778 mt76: validate rx CCMP PN
302af90 mt76x2: init: disable all pending tasklets during device removal
9f685fe mt7603: init: disable tbtt tasklet during device removal
c6f8cac mt76: let mac80211 validate CCMP PN for fragmented frames
3968dae mt7603: fix 40 mhz channel bandwidth reporting
9c2e03d mt7603: fix rx LDPC reporting
f515dfc mt76: implement AP_LINK_PS
974142c mt76: implement processing of BlockAckReq frames
c5209db mt76: avoid re-queueing A-MPDU rx reorder work if no frames are pending
e67e7a5 mt76x2: do not set status->aggr for NULL data frames
8693864 mt76: check qos ack policy before reordering packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The nf_reject_ipv4 and nf_reject_ipv6 modules are moved into separate
packages, as they are a common dependency of ip(6)tables and nftables. This
avoids a dependency of nftables on kmod-nf-ipt(6). Also, fewer iptables
modules depend on nf-conntrack(6) now.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The IGB and IXGBE drivers depend on kmod-hwmon core now.
Fixes: af707a178f ("netdevices.mk: add hwmon to IGB and IXGBE drivers")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Off-chip NICs can run hotter than the CPU, so they're definitely
worth instrumenting.
Adding hardware monitoring increases by ~3744 and ~2672 bytes,
respectively, the sizes of the igb.ko and ixgbe.ko drivers.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This reverts commit 53f62bc5e5.
commit made the builders fail with
"Package kmod-igb is missing dependencies for the following libraries: hwmon.ko"
Signed-off-by: John Crispin <john@phrozen.org>
The IGB and IXGBE drivers depend on kmod-hwmon core now.
Fixes: af707a178f ("netdevices.mk: add hwmon to IGB and IXGBE drivers")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Off-chip NICs can run hotter than the CPU, so they're definitely
worth instrumenting.
Adding hardware monitoring increases by ~3744 and ~2672 bytes,
respectively, the sizes of the igb.ko and ixgbe.ko drivers.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Revert upstream commit 1bd773c077de "wireless: set correct mandatory rate
flags", as it breaks 11s interoperability: nodes can only associate when
neither or both have this patch. As this is a regression from released
versions, revert to the old code for now.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The iptables TRACE target is only available in raw table that's why the
dependency was moved from iptables-mod-trace into kmod-ipt-debug
Fixes FS#1219
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2b7fae4 mt76: fix returnvar.cocci warnings
939e3e0 mt76x2: dfs: avoid tasklet scheduling during mt76x2_dfs_init_params()
cf59170 mt76x2: dfs: add set_domain handler
5e4d60e mt76x2: dfs: take into account dfs region in mt76x2_dfs_init_params()
f76e25f mt76x2: fix WMM parameter configuration
34d612d mt76: retry rx polling as long as there is budget left
0f8327a mt76x2: fix TSF value in probe responses
ad3f8e9 mt76: add an intermediate struct for rx status information
58a41f1 mt76: get station pointer by wcid and pass it to mac80211
b0508d3 mt76: implement A-MPDU rx reordering in the driver code
cf3cfc4 mt76: split mt76_rx_complete
461cdf9 mt76: pass the per-vif wcid to the core for multicast rx
9b2c778 mt76: validate rx CCMP PN
302af90 mt76x2: init: disable all pending tasklets during device removal
9f685fe mt7603: init: disable tbtt tasklet during device removal
c6f8cac mt76: let mac80211 validate CCMP PN for fragmented frames
3968dae mt7603: fix 40 mhz channel bandwidth reporting
9c2e03d mt7603: fix rx LDPC reporting
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit 666e9cf222.
The change has not been build-tested on non-x86 targets and leads to
stalled kernel builds due to unset configuration symbols there.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The kmod-lp package included both lp.ko and ppdev.ko, but ECP device
drivers may or may not require lp NOT to be loaded, needing only ppdev.
Additionally, There were no packages for any parport interface modules,
such as uss720 or parport_pc, provided here. It has not been otherwise
possible to use PC-style parport hardware for kmod-lp.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unconditionally enable connmark support and tie it to the conntrack core
module to allow removing this kernel configuration dependency from the
xtables-addons package.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Backport patches that separate spectral scan support from general debugfs
support of ath9k/ath10k; this allows to remove the dependency on
KERNEL_RELAY from these driver packages even with debugfs enabled and
avoids the memory footprint of the relay buffers allocated by ath9k/ath10k
even when they aren't used at all.
The KERNEL_RELAY dependency is moved to a new config symbol that enables
spectral scan support in these drivers.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
More important bug fix:
402f05c Use full-rate mtu_time in all tins. Fixes an issue where some
cake tins experienced excessive latency since 49776da (dynamically
adjust target)
Minor bug fixes:
31277c2 Avoid unsigned comparison against zero. Fix compiler warning,
no known impact.
8cf5278 ack_filter: fix TCP flag check. A very contrived case may have
lead to dropping a SYN packet that should not be dropped.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:
local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
kern.info kernel: dsl0: renamed from nas0
kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
local2.err br2684ctl[1667]: Could not configure interface:No such device or address
By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.
Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes the following dependency error encountered by the buildbots:
Package kmod-w1 is missing dependencies for the following libraries:
hwmon.ko
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The NXP 74HC164 GPIO expander driver uses a different config symbol
("CONFIG_GPIO_74X164") and module name since since at least Kernel
version 2.6.37.
Update the kmod package definition accordingly by adjusting kconfig
and module file names.
This unrelated, but correct change has been separated from the
WNR2000v5 support commits.
Ref: https://github.com/lede-project/source/pull/1256
Suggested-by: Raphael Catolino <raphael.catolino@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add the uas(p) module to the modules loaded early on the boot process.
The uas(p) is an modern alternative, which is used by the modern USB3
storage cases, compared to the bot protocol. To be able to use uas(p)
storage cases for extroot, the kernel module has to be loaded before the
search for extroot has been called. This patch changes the load order to
support uas(p) storage cases for extroot.
Signed-off-by: Daniel Albers <daniel.albers@public-files.de>
Fix overhead accounting error introduced by f33c4d6 refactor
cake_advance_shaper and ack_filter
Symptoms were links running under rate.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Intel motherboards (as well as the Cavium ThunderX SoC) use a
superset of the I2C protocol called SMBus.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
kmod-lib-lzo and kmod-lib-lz4 depend in kernel 4.14 on
kmod-crypto-acompress, add this missing dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_FRAMEBUFFER_CONSOLE does not activate new modules any more in
kernel 4.14, but CONFIG_FRAMEBUFFER_CONSOLE is now a boolean option
which change the kmod-fb package. kmod-fbcon should be split up.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This deactivates the following options which were introduced between
kernel 4.9 and 4.14 in some kernel packages:
CONFIG_INET_ESP_OFFLOAD
CONFIG_INET6_ESP_OFFLOAD
CONFIG_LWTUNNEL_BPF
CONFIG_NET_9P_XEN
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 kmod-bluetooth depends on kmod-crypto-ecdh, add
kmod-crypto-ecdh to LEDE.
Both packages also depend on the kmod-crypto-kpp package. To build this
we have to fix the dependency of CRYPTO_ECDH which has a typo.
This patch is already accepted upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 kmod-crypto-hw-ccp depends on kmod-crypto-rsa, add it.
kmod-crypto-rsa also packages the ASN1 parser and some other code which
is currently only used by this module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 kmod-dm depends on kmod-dax.
Add DAX: "Direct access to differentiated memory" to LEDE.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 hwmon support can be deactivated for the tg3 driver,
deactivate it by default to save some space.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The default e1000e parameters (interrupt throttling rate, MSI/MSI-X
mode) are optimized for desktop and server computers to optimize
user-space execution (i.e. what's typically referred to as "useful"
work). This assumption breaks on a router under load where most of
the "useful" work actually takes place either in hardware interrupt
handlers (IRQ) or at software IRQ (swirq) modes, so we try to reflect
that by overriding these parameters with more appropriate values.
Patch-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
There has been recent significant activity with the cake qdisc of late
but in the cobalt branch. Some of that effort is related to upstreaming
to kernel & iproute2 mainline but we're not quite there yet. Relevant
feature changes:
ingress mode: Instead of only counting packets that make it past the
shaper, include packets we've decided to drop as well, since they did
arrive with us on the link and took link capacity.
This mode is more suitable for shaping the ingress of a link
(e.g. from ISP) rather than the more normal egress.
ptm mode: Minor optimisation in packet overhead calculation.
dual-src/dsthost/triple-isolate: Optimise only calculating src or dst
host hashes only if required.
ack-filter/ack-filter-aggressive: Filter excessive TCP ACKS. Useful in
highly assymetric links (downstream v upstream capacity) where the
majority of upstream link capacity is occupied with ACKS for downstream
traffic.
A separate iproute2 patch to teach it about Cake's new features will
follow.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
d02a05b mt7603: update firmware to version 20160107100755
4d4cd05 Partially revert "mt7603: use mcu command to set timing registers, fix OFDM timeout values"
170f334 mt76x2: remove MAC address limitation for multi-vif setups
3563b8f mt76x2: clean up MAC/BSSID address initialization
9de77e1 mt76x2: drop wiphy->addresses
a6a6e25 mt76x2: init: disable APCLI by default
c64633e mt76x2: configure rx filter based on monitor mode setting
ac815fa mt76x2: init: fix rx filter default value during init
e504656 mt7603: configure other-unicast drop based on monitor mode setting
Signed-off-by: Felix Fietkau <nbd@nbd.name>
11f42a8 mt76x2: add channel argument to eeprom tx power functions
3bd7e76 mt76x2: initialize channel power limits
19fff41 mt76x2: convert between per-chain tx power and combined output
737cf2b mt7603: rename mt7603_mac_reset to mt7603_pse_reset
8026638 mt7603: rename MT_PSE_RESET register
c4dd32a mt7603: remove watchdog reset on interface stop
d99092b mt7603: remove WARN_ON_ONCE for workaround checks
c8807b4 mt7603: simplify PSE reset
d8a5990 mt7603: warn if PSE reset fails
c079960 mt7603: clean up dma debug reads
96817d6 mt7603: make mt7603_mac_watchdog_reset() static
e953c78 mt7603: clear wtbl PS bit for powersave responses
57a2e33 mt7603: set tx-skip flag for powersave clients
c8e5ab1 mt7603: initialize wtbl ps flag on station add
b4034cf mt76x2: remove some harmless WARN_ONs in tx status and rx path
8e17d36 mt7603: remove some harmless WARN_ONs in rx path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Latencies can be much higher on wifi devices, especially with
aggregation. Tune the network stack setting introduced in the previous
commit to account for that.
This commit reintroduces the previously reverted one with a fix for the
crash issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit 2dc485250d.
This patch needs some additional checks in order to avoid overwriting
unrelated fields for request sockets.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
dfb2f6c pkt_sched: make compile again
5ab7026 sch_cake: make compile again
6f28803 codel5: make more checkpatch compliant
bd426aa Fix build error on 4.12
e4a3628 Whitespace tidy up
Signed-off-by: Fushan Wen <qydwhotmail@gmail.com>
Fix the target dependency to make it possible to select this module also
on x86 target and its subtargets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The firmware directory in the Linux kernel was removed in kernel 4.14,
take the e100 firmware files now from the linux-firmware repository
instead. To do so create the new package e100-firmware. This will also
work with older kernel versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds NFS4 client support:
1. Package kmod-fs-nfs is split into kmod-fs-nfs (nfs.ko) and
kmod-fs-nfs-v3 (nfsv3.ko).
2. A new package kmod-fs-nfs-v4 (nfsv4.ko) is created.
3. Package kmod-fs-nfs-common-v4 is renamed to kmod-fs-nfs-rpcsec
and includes additional module rpcsec_gss_krb5.ko.
CONFIG_NFS_V4 goes into kmod-fs-nfs-v4, CONFIG_NFSD_V4 (NFS4
server) is removed. Missing kernel module oid_registry.ko
needed by auth_rpcgss.ko is added to the package.
A new package kmod-crypto-cts needed by rpcsec_gss_krb5.ko is
also created.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
[add dependency to kmod-crypto-ecb in fs-nfs-common-rpcsec]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The module parameters "nogameport=1" and "nocir=1" are needed,
because this is not supported on recent chips and doesn't
really tell if the system is stable.
As this features will already be removed in linux-4.13 or newer,
this module parameters can be removed in the future.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
The DEFINE_PCI_DEVICE_TABLE macro was removed with upstream commit
7e9321599011 ("treewide: remove references to the now unnecessary
DEFINE_PCI_DEVICE_TABLE").
Use the pci_device_id struct to fix the acx-mac80211 build failure on
ramips.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The kernel firmware/ is going away, so pull this firmware
from the linux-firmware git repo instead. No actual changes
to the installed files.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Significantly improves throughput on MT76x2, fixes some stability
issues, adds LED support.
Changes:
266ef38 mt76x2: mcu: remove unused parameter in mt76x2_mcu_msg_alloc signature
758376d mt7603: mcu: remove unused parameter in mt7603_mcu_msg_alloc() signature
e764787 Fix errors found by cppcheck
a6fce8a mt7603: add LED definition registers
f658dd2 mt76x2: add LED register definitions
f6a021d mt76x2: Support using PCI ID as chip ID
c9bdcd8 mt76: add led support using mac80211 led framework
58e9138 mt76x2: init: add ma80211 led callbacks
8ea8da3 mt7603: init: add ma80211 led callbacks
ded88cd mt76x2: Add PCI identifier for MT7602
51a6764 mt7603: remove unnecessary mcu register read function
fbdbf65 debugfs: add support for changing the LED pin
cc02e49 mac80211: move DT led configuration to the "led" child node
e4e7734 mt76x2: limit client WCID entries to 0-127
60172cc mt76x2: clear drop flag for all WCIDs on init
d8140b6 mt76x2: clear per-WCID tx rate lookup register
0ce7923 mt76x2: add helper function for setting drop mask
ccc4baf mt76x2: clear drop mask when sending a PS response
ff60d14 mt76: increase rx ring size for mt76x2
b57ada5 mt76x2: add rx statistics registers
af425de mt76x2: fix LNA gain register annotation
efd7724 mt76x2: sync channel gain value with latest reference driver
4af37bd mt76x2: implement dynamic AGC tuning based on false packet detection count
70f2002 mt76x2: add more gain tuning based on the latest reference driver
8f1c8ab mt76x2: sync tx power related values with reference driver
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Latencies can be much higher on wifi devices, especially with
aggregation. Tune the network stack setting introduced in the previous
commit to account for that
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The wireless regdb is now loaded via firmware loading, CRDA support and
built-in regdb support have been removed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
