Building for octeon fails with
'arch/mips/vdso/vdso-n32.so.dbg' already contains a '.MIPS.abiflags'
section
if the file already exists from a prior build.
Use the same workaround as the one for vdso.so.dbg committed in
9eb155353a.
Commit 91f205acaf extended the workaround
to cover vdso-o32.so.dbg but missed the vdso-n32.so.dbg which is added
now by this change.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch introduces serial0 aliases in the ramips DTS files, which can
then be used to denote the active console instead of relying on bootargs.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
This router only has one ethernet port, so a VLAN is useless here, now that the rt3050 TCP bug that happened without VLANs has been fixed for a very long time.
Add this router to the VLAN-less config that is used by other single-port routers.
Also fix MAC address detection code since this router has no WAN port.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Some routers only have one port, so eth0 is used without VLANs for them.
Revision r47720 introduced some changes, but wrongly confused "enable" with "reset".
VLANs need to be disabled for those routers, and the switch may be reset.
Fix this, by explicitly disabling VLANs instead of resetting the switch for these routers.
Also merge duplicate configuration for the "m2m".
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
The new rt3050 switch driver doesn't have problems with TCP when not
using VLANs.
This piece of code also broke failsafe for all routers where the LAN
port is not wired to port 0 of the internal switch.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49293
Port 0 is the only ethernet port on this router, so disable all other PHYs
in order to save power.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49292
Port 4 is the only ethernet port on this router, so disable all other PHYs
in order to save power.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49291
This patch allows configuring ports to be disabled in the device tree; this
saves power, since disabling ports here actually disables power to ethernet
PHYs.
Line 444 enables all ethernet ports, so line 487 is getting zero ports to be
disabled, except for port 5 in SoCs where this is not implemented as it will
be sticky disabled in register POC0. Because of this, the code will still read
the switch configuration and OR it to the device tree setting.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49290
Line 444 is actually enabling all switch ports by setting the disable bits
to 0. This needs to be done because the bootloader sets all ports to disabled
by default (which is the case for at least one router based on RT5350).
So, this patch fixes the comment in line 443.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49289
The FCT2 esw register should be set to 0x2500C to have "unknown IPv6
multicast" packets broadcasted to every port, instead of dropped.
The previous value only let those packets go through ports 1 and 3.
"Unknown IPv6 multicast" packets include packets needed by ICMPv6 echo
requests addressed to well-known addresses, such as ff02::1 (MAC address
is 33:33:00:00:00:01 in this case).
Please note that by default ICMPv6 echo requests to ff02::1 are not replied
to by the router because of ip6tables considering those packets to be invalid.
But this is another bug/patch. ;)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49287
VGV7510KW2 with VRX288 v1.2 has brnboot 1.8 installed. Starting with
this brnboot version, the "GPHY Clock Source" isn't set anymore by
brnboot, with the result that xrx200-net fails to probe/initialize the
phys.
Use the phy clock source device tree binding to specify the clock source.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49284
brnboot based devices can have two Image partitions. When flashing
images via the brnboot recovery web interface, the Image partitions are
written alternating.
The current active Image partition is stored in the first byte of the
Primary_Setting partition by using 0x00 for Code_Image_0 and 0x01 for
Code_Image_1.
By using the information about the active "Code Image", it is possible
to ensure that the rootfs belongs to the current booted Image/Kernel.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49281
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49280
Use the same name for TP-Link images as it was with the old image build
code.
Move the BOARD_ID export to the TP-Link image build recipe, to indicate
that the variable is only related in this context.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49279
Based on the vg3503j_gphy_led.sh script published in the VG3503J wiki
article, the OEM Firmware uses the following PHY led functionality:
gphy led 0: LINK/ACTIVITY
gphy led 1: LINK
gphy led 2: ACTIVITY
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49278
The VGV7510KW22 has the leds for LAN1-3 connected to pin1 of the phys
and the led for LAN4 connect to pin0 of the phy. This results with the
current configuration in a fast flashing LAN4 led as soon as a network
cable is connected. Something similar was reported on the forum[1] for
the VGV7519 as well.
Since it isn't predicable to which pin a (single) phy led is connected,
use the (default) pin1 functionality
Constant On: 10/100/1000MBit
Blink Fast: None
Blink Slow: None
Pulse: TX/RX
for all ethernet phy leds.
After checking pictures of all vr9 boards, it looks like only the VG3503J
has more than one led connected per phy. Using the phy led device tree
bindings to assign the functionality to the "additional" leds, the
VG3503J phy leds should behave as before.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
[1] https://forum.openwrt.org/viewtopic.php?pid=321523
SVN-Revision: 49270
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49268
Building for octeon fails with
'arch/mips/vdso/vdso-o32.so.dbg' already contains a '.MIPS.abiflags'
section
if the file already exists from a prior build.
Use the same workaround as the one for vdso.so.dbg committed in
9eb155353a.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Currently the build fails with
'arch/mips/vdso/vdso.so.dbg' already contains a '.MIPS.abiflags' section
if the file already exists from a prior build.
Add a makefile rule to force the rebuild of vdso.so.dbg if genvdso has
has been changed to workaround the failure.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
For some time now m25p80 supports 32 MiB flashes and we just needed to
patch spi-nor to support JEDEC incompatible w25q128. Also by switching
to m25p80 we gain accelerated SPI flash reads.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49260
Commit 8c130dd (lantiq: use new image build process for some images) broke
image generation for the xway target since the generated macros reference not
existing WBMRA.dts and WBMRB.dts files leading to the following build error:
mips-openwrt-linux-musl-cpp: error: ../dts/WBMRA.dts: No such file or directory
mips-openwrt-linux-musl-cpp: warning: '-x assembler-with-cpp' after last input file has no effect
mips-openwrt-linux-musl-cpp: fatal error: no input files
Previously both the WBMRA and WBMRB profiles shared a common WBMR DT since
the only difference is the embedded firmware kmod package.
Extend the lantiqImage macro to optionally support specifying a different
DTS file and use this facility to let the both WBMR profiles reference the
correct device tree file.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This regression was introduced while rebasing LEDE's commits over the latest
OpenWrt repository.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The kmod-acpi-button functionality is included in the kernel where needed
and the corresponding kmod package has been deleted long ago, therfor drop
the remaining references now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update to latest make_ext4fs Git HEAD to fix build with recent glibc version
which does not implicitely includes sysmacros.h anymore.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The libc and kernel package files moved since the introduction of shared
packages and the changed output directory layout. This causes the generated
ImageBuilder archive to lack the necessary "libc" and "kernel" meta packages,
leading to opkg install errors later on.
Use the FeedPackageDir macro to figure out the proper source directory to use.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Bundle all firmware files which have been built along with the kernel to fix
packaging of kmods in the SDK environment that rely on in-tree firmwares,
specifically kmod-e100.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Implement a crude but functioning sysupgrade image check for the
Raspberry Pi. The code only checks if the master boot record boot
signature (0x55aa) is present in the first 512-bytes at the correct
location. This can prevent the odd bricking of a system when flashing
the wrong file.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
This update also adds individual download of firmware files instead of fetching
every file on the repository (10-MiB vs 100+MiB).
Also copy Linux license from kernel directory instead of using the rpi-firmware
one.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The dwc2 USB driver now works on Lantiq ar9, but the
default is still ltq-hcd-ar9. This patch switches to
dwc2 by default.
v2: all ar9 boards (v1 was just for BTHOMEHUBV3A and WBMR)
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 49254
The only way to access the u-boot console on the BTHOMEHUBV3A
is by soldering a serial console onto some really tiny pads.
To enable installation without soldering it would be helpful
to be able to modify the uboot environment from within
the ramdisk image used as part of the installation process.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 49253
Remove read-only flag on two partitions on BTHOMEHUBV3A:
uboot-config - otherwise fw_setenv command cannot be used.
ath9k-cal - so that ath9k calibration data can be copied
to the partition on a newly installed board.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 49250
Fixes some DMA issues with this platform. Because this isn't currently accepted,
and can potentially disrupt other platforms (as read in commit log), I will
leave this cns3xxx specific.
Original Patch: https://patchwork.ozlabs.org/patch/600024/
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 49249
Fix is required to properly set pci config bits.
Original Patch: https://patchwork.ozlabs.org/patch/596170/
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 49248
This patch adds support for the TP-Link TL-WR740N v6 into OpenWrt trunk. Hardware wise, it's very similar to the TL-WR841N v10. See the forum thread [1]. Credit goes to the user 'traveler' who did the legwork and tested builds.
Also thanks to Matthias Schiffer for clarifying the DEVICE_PROFILE settings.
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
[1]: https://forum.openwrt.org/viewtopic.php?pid=318704
SVN-Revision: 49245
Dynamic allocation of label can be simplified.
Also add error handling to deal with failed memory allocation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 49244
LZMA compress the kernel without dictionary, otherwise brnboot fails to
uncompress the kernel.
The filesystem parameter of mkbrncmdline was dropped since the used
filesystem isn't exported in the kernel build step and at least in my
tests everything works without the parameter. If the parameter is
required for some reason, the static keyword "squashfs" can be used.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49241
Set the kernel entry address to the same value as it is used for the old
image build build process.
Fixes boot of uImages on VGV7510KW22NOR and others.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49237
CS-QR10 is MT7620A based IP Camera.
the camera and sound does not work with kernel 4.4.
- camera chip is sn9c291.
- sound chip is wm8960.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49234
Makes the patches apply again by fixing the white space broken patch.
This problem was introduced in r49212.
Closes#22248 and #22259
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49221
