This updates samba to the most recent minor version.
This patch is based on a patch by Anton van Bohemen <avbohemen@ziggo.nl>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 40618
This patch fixes compilation failure for hostapd when using eglibc 2.15.
Signed-off-by: Zachery Stoddard <zacherystoddard@gmail.com>
SVN-Revision: 40575
Gives the user the control to select the correct WAN IPv4 address to be used by the 6rd tunnel when mutiple WAN interfaces are configured
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 40566
This patch implements support for 802.11s protected mesh wireless networks (using authsae) in the netifd framework.
Until meshd-nl80211 implements a proper -P option for the PID file, this uses shell backgrounding in order to be able to get the PID for the process.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 40497
r39995 introduced a new parameter wps_pbc_in_m1 to wifi wps config, but
apparently did not provide a default value 0.
When that option's non-existing value is later evaluated in
/lib/netifd/hostapd.sh, it causes the "bad number" error to be logged in
syslog if user has not set the wps_pbc_in_m1 option. The error materialises
only if user has enabled wps.
Sat Apr 12 13:25:01 2014 daemon.notice netifd: radio1 (1254): sh: bad number
Sat Apr 12 13:25:01 2014 daemon.notice netifd: radio0 (1253): sh: bad number
Discussion in bug 15508: https://dev.openwrt.org/ticket/15508#comment:3
Error is caused by line 282:
https://dev.openwrt.org/browser/trunk/package/network/services/hostapd/files/netifd.sh#L282
My patch sets the parameter's default value to 0, which does nothing. The
default might also be set a bit later in the function, but this felt like the
most clear place to do that.
Signed-off-by hnyman <hannu.nyman@iki.fi>
SVN-Revision: 40469
* atm module needs to be loaded before linux-atm
* use absolute firmware paths
* extended validation
* add a script for mounting an optional firmware partition
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40460
fixes incremental build with change to CONFIG_DROPBEAR_ECC
drop --with-shared which is unknown to configure
Patch by Catalin Patulea <cat@vv.carleton.ca>
SVN-Revision: 40300
Without timeout mechanism, if ssh client disconnected without sending
FIN or RST, forked dropbear servers would hang there for
KEX_RETRY_TIMEOUT seconds (8 hours).
TCP keepalive is not implemented in dropbear yet, thus the name
SSHKeepAlive.
300 seconds in this patch is selected from the default value of
ServerAliveInterval for Debian ssh client (See man ssh_config).
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 40299
Option pbc_in_m1 is being used as a WPS capability discovery
workaround for PBC with Windows 7.
Add possibility to enable this workaround from UCI.
To enable it, turn on wps and set wps_pbc_in_m1 parameter to 1.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
SVN-Revision: 39995
This patch removes dependancy of PPP from chat application as chat application can be used for other serial communication as well that is not dependant on PPP and therefore one should be able to install chat without PPP. There also are no dependencies within chat application for PPP.
Signed-off-by: Oskari Rauta <oskari.rauta at gmail.com>
SVN-Revision: 39992
This change creates a new ip-full variant for the ip package.
It disables IP_CONFIG_TINY to make some iproute2 features available like xfrm, gretap, ...
Signed-off-by: Thomas Wouters <thomaswouters@gmail.com>
SVN-Revision: 39854
* Reduce RA/DHCPv6 spam filter to 30s by default and make it configurable
* Don't set nd_ra_{reachable,retransmit] to 0 when received in RAs
SVN-Revision: 39775
Similarly to the previously broken address pools, DNS-servers and some
MSRs could be advertised incorrectly as well. This is now fixed.
SVN-Revision: 39739
- Do not consider bitmap storage for IPv6 family sets
- Move ipset family parameter before any additional option
- Only emit family parameter for hash sets
- Do not allow IPv6 iprange for IPv4 sets and vice versa
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39647
6in4 historically allowed an ip6addr without a mask however the newly
introduced source-routing segfaulted in this scenario (#14958 + #14858).
Fixes include: "Fix ubus route src mask printing" and
"Disable netlink auto ack" (thanks to Hans Dedecker)
SVN-Revision: 39586
- update iw to 3.14
- remove some patches that are obsolete
- 200-reduce_size.patch has new coalesce removed from Makefile matching prev. ver
- refresh patches
This increases the size of the binary by 6.7%:
87801 4400 320 92521 16969 iw-3.10/iw
93995 4424 324 98743 181b7 iw-3.14/iw
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 39486
This patch introduces 802.11ac support to mac80211 and hostapd. The split of
VHT160 in two 80 MHz bands is not yet supported, since it requires an
additional user supplied parameter for the channel of the second band.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
[sven@open-mesh.com: Rebased patch, merged htmode and vhtmode,
removed special hwmode, replaced uci vht_capab list with overwritable
autoconfig, fixed hostapd integration, fixed commit description, add HT40+/-
for VHT modes, add VHT40 center_freq autoconfig, refactored major parts]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 39456
Latest changes broke source-restriction of on-link routes. Restoring
old-behaviour but adding correct source-restrictions which prevents
the offlink handler to remove the on-link route.
SVN-Revision: 39454
* Fixed broken stateless-mode (fixes#14863)
* Support for multiple IAIDs, improved server compatibility,
improved NTP/SNTP support and other fixes (thanks to T-Labs)
SVN-Revision: 39433
Make the IPv4 "do not fragment" bit a configurable variable for the 6rd
tunnel interface as the bit should not be set in the encapsulating IPv4
header according to RFC3056.
On top the config variable allows to enable/disable path mtu discovery
for tunnel interfaces.
Config variable can be passed to netifd as tunnel config support is
already present for the "do not fragment" bit.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 39370
Introduced by ("netifd: add wireless configuration support and port mac80211 to
the new framework")
Reported-by: René van Weert <r.vanweert@sowifi.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
SVN-Revision: 39288
Introduced by ("netifd: add wireless configuration support and port mac80211 to
the new framework")
Reported-by: René van Weert <rene@sowifi.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
SVN-Revision: 39231
- cache udhcp check results to speed up subsequent reloads
- enable procd file tracking for /var/etc/dnsmasq.conf to only reload service if needed
- implement reload action to only restart dnsmasq if /var/etc/dnsmasq.conf actually changed
- launch dnsmasq from interface hotplug to avoid race conditions with network bringup
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39152
The firewall3 implementation as well as the shell implementation predating it
used to process the tcp_ecnoption as boolean while it actually is an integer.
Change the code to parse tcp_ecn as integer.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39122
This commit changes the dnsmasq init script to use the interface
status exposed by netifd. The old references to scan_interfaces()
and (indirect) accesses to uci state variables are removed and
replaced with corresponding network_*() calls.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39101
Before this patch, if we specify a plugin specific option through
`pppd_options` in /etc/config/network, e.g. `rp_pppoe_verbose 1`, pppd
would quit with the following error in log.
Wed Oct 9 09:42:58 2013 daemon.notice netifd: GORG (1689): /usr/sbin/pppd: unrecognized option 'rp_pppoe_verbose'
Wed Oct 9 09:42:58 2013 daemon.err pppd[1689]: unrecognized option 'rp_pppoe_verbose'
Wed Oct 9 09:42:58 2013 daemon.notice netifd: GORG (1689): pppd version 2.4.5
Wed Oct 9 09:42:58 2013 daemon.notice netifd: GORG (1689): Usage: /usr/sbin/pppd [ options ], where options are:
This is due to the requirement that function add_option() should be
called by the plugin_init() function first before pppd can parse those
options.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 38911
- instead of writing one (or more) ACCEPT rules in the filter table
for each redirect install a global ctstate DNAT accept rule per zone
- discard rules and redirects which have invalid options set instead
of silently skipping the invalid values
SVN-Revision: 38849
The correct bits are now cleared in the IPv6 address as the shift
value to the correct byte in the IPv6 address was wrong. Depending
on the stack values this could result in a hanging 6rdcalc program
due to an endless loop.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 38818
The associations list for Broadcom WDS interfaces are duplicate to those
reported by the corresponding AP interface; so there is no need to report
them again.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38746
Modify the hwmodelist reporting for broadcom devices to include
proper reporting of 802.11n support.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38745
Changeset r36943 ("dnsmasq: use host-record instead of address") removed
the automatic domain expansion for config domain sections, this breaks
existing setups and alters the old behaviour in unexpected ways, therfore
restore behaviour of the current stable release.
Additionally handle fully qualified hostnames properly when setting up the
own hostrecord by stripping the local domain part form the given name
instead of unconditionally appending it, so that "example.lan" results
in "example example.lan" and not "example.lan example.lan.lan".
SVN-Revision: 38648
- clean up duplication of procd instance handling code
- using --cd *after* --config is rather pointless
- to be able to log errors properly, --syslog needs to be passed before --config
- tell procd about the generated or referenced config file instead of
the uci file. this avoids having to restart all instances if only one
of them changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38632
* Various RFC compliance fixes (thanks to Hans Dedecker)
* Fix RA spam filter logic causing ipv6 connection issues
* Fix parameters -F and -P being order dependent
SVN-Revision: 38577
* Use network.interface dump call instead of individual status calls
to reduce overall netifd lookups and invokes to 1 per fw3 process.
* Allow protocol handlers to assign a firewall zone for an interface
in the data section to allow for dynamic firewall zone assignment.
SVN-Revision: 38504
* Add ubus methods for global interface status
* Add ubus function to create nested interfaces
* Add protocol update notifications and hotplug legacy calls
* Fix: key to data elements point at wrong memory area
* Add support for source-restricted routes
* Add option "delegate" to toggle prefix delegation
* Reevaluate target routes also on interface update
SVN-Revision: 38453
A similar change was recently merged in iw commit
58b46da26ab9b5ff31c7033e175351eb1301d9af
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 38449
There are several cases within 'luci' that attempt to access the interface
'type' from within the 'type' specific meta tables; however, 'type' is not
currently available there. Replicate the common metadata in the 'type'
specific meta tables.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38448
Possible parameters are yes, no and adaptive. See manpage for more information.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
SVN-Revision: 38412
* Make SOL_MAX_RT configurable and default back to 120s
* Prefer servers with bigger prefixes (allows to use Comcast /60)
* Don't hang indefinitely if DHCPv6 REQUEST is not answered
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 38393
The switch driver is not used by brcm47xx any more and can be removed,
instead of this switch driver b53 is used now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38387
There are certain consumer devices which are outliers in protocol conformance.
An example is Samsung bluray players, which require broadcast DHCP responses
(on Ethernet only, strangely not on Wifi).
By specifying:
config host
...
option broadcast 1
this will enable the response to be sent as an Ethernet broadcast and not as
a unicast.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 38365
- do not insert duplicate rules when setting up reflection to a zone containing multiple interfaces
- set up reflection for any protocol, not just TCP and UDP
SVN-Revision: 38361
proto_pptp_setup is responsible for loading the required modules to establish
a pptp connection to a foreign peer. The function checks whether all required
modules are already loaded, before actually loading them.
It seems that the filter being used to accomplish this, is not restrictive
enough in some cases. For instance when pptp nat helper modules are present on
a system, and already loaded before a pptp connection is enabled. Then the
search filter (possibly) returns the following for module=pptp, where actually
no matches are expected, resulting in the pptp.ko module not being loaded,
thereby failing to establish the pptp connection.
# module="pptp" ; grep "$module" /proc/modules
nf_nat_pptp 1312 0 - Live 0x86ce7000
nf_conntrack_pptp 3072 1 nf_nat_pptp, Live 0x86cb9000
nf_nat_proto_gre 784 1 nf_nat_pptp, Live 0x86cba000
nf_conntrack_proto_gre 2368 1 nf_conntrack_pptp, Live 0x86cbf000
nf_nat 9792 13 nf_nat_rtsp,nf_nat_tftp,nf_nat_sip,nf_nat_pptp,nf_nat_h323,nf_nat_proto_gre,nf_nat_amanda,nf_nat_irc,nf_nat_ftp,ipt_REDIRECT,ipt_NETMAP,ipt_MASQUERADE,iptable_nat, Live 0x86ca8000
nf_conntrack 37264 31 nf_nat_rtsp,nf_conntrack_rtsp,nf_nat_tftp,nf_conntrack_tftp,nf_nat_snmp_basic,nf_conntrack_snmp,nf_nat_sip,nf_conntrack_sip,nf_nat_pptp,nf_conntrack_pptp,nf_nat_h323,nf_conntrack_h323,nf_conntrack_proto_gre,nf_nat_amanda,nf_conntrack_amanda,nf_conntrack_broadcast,nf_nat_irc,nf_conntrack_irc,nf_nat_ftp,nf_conntrack_ftp,ipt_MASQUERADE,iptable_nat,nf_nat,xt_helper,xt_connmark,xt_connbytes,xt_conntrack,xt_CT,xt_NOTRACK,xt_state,nf_conntrack_ipv4, Live 0x86c90000
The search filter can be made more accurate/restrictive, by requiring the
occurance of the exact name of the module at the beginning of a line in
/proc/modules.
# module="pptp" ; grep "^$module " /proc/modules
pptp 13296 2 - Live 0x86e80000
Signed-off-by: Tijs Van Buggenhout <tvb@able.be>
SVN-Revision: 38358
Currently, in order to configure the authentication daemon in
8021x mode, we need to set wireless.@wifi-iface[0].encryption="wpa"
Though it works it confuses folks as 8021x is using WEP
encryption and not WPA. Therefore the terminology itself is
confusing. This change adds 8021x as a recognized string for 8021x
authentication.
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38339
Setting wireless.@wifi-iface[N].ext_registrar=1 will enable UPNP
advertising and add an external registrar to the interface this vif
belongs to (br-lan if the vif is included in the LAN bridge). By
enabling this we append upnp_iface=xxx to the hostapd config file.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38338
Enable CONFIG_WPS2 for hostapd. This is required to support
options like Virtual Push Button in WPS.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38337
