All these devices share the exact same image format.
The usb3 kmod is added for the rbm11g, as the rbm11g has a mini-pcie
slot like its bigger sibling. The usb kmod is necessary for
usb-over-pcie support, which is mandatory for a lot of LTE modules.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost
the same as FB7330, but only one ETH-Port and no USB.
Hardware
SoC: Lantiq Xway ARX188 PSB 50812 EL
RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5)
Ethernet: Atheros 8030
Wireless: Atheros AR9227 b/g/n 2x2
DSL: Lantiq ADSL2+
DECT: Dialog SC14441
Buttons: WiFi, DECT
LEDs: Power/DSL, Fon, DECT, WLAN, Info
LEDs
Power: GPIO#44 (active low)
Internet: GPIO#47 (active low)
DECT: GPIO#38 (active low)
WLAN: GPIO#37 (active low)
Info: GPIO#35 (active low)
The Fon LED is labeled as internet in avm gpl sources.
Buttons
WLAN: GPIO#1 (active low)
DECT: GPIO#2 (active low)
Phy
GPIO#03: 25 MHz
GPIO#34: Reset (active low)
GPIO#39: Int
GPIO#42: MII MDIO
GPIO#43: MII MDC
PCIe
GPIO#21: reset (active low)
Installation:
To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
ftp> quote REBOOT
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Use of_mdiobus_register() to pass the ethernet phy node to the phy
drivers. This is needed for the at8030 phy driver which needs to know
the GPIO which is connected to the ar8030 reset pin.
This driver expects a child in gsw/etop node named "mdio-bus", which has
the ethernet phys defined:
&gsw {
phy-mode = "rmii";
phy-handle = <&phy0>;
mtd-mac-address = <&ath9k_cal 0xa91>;
mtd-mac-address-increment = <(-2)>;
mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
};
};
};
Fallback to mdiobus_register() if no mdio-bus child node exists. This
way we don't need to touch all xway dts files, for which we don't know
the actual address on the mdio bus.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Restarting service sysctl echos multiple errors like:
sysctl: -e: No such file or directory
After the first filename, all remaining arguments are treated
as files.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
The mac address for the 2.4 wireless need to be decremented by one.
Correct MAC adress increments for this board are:
wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Add each variant to the matching PROVIDERS variables after evaluating
the respective hostapd*, wpad* and wpa* variant.
Each package providing the same feature will automatically conflict with
all prior packages providing the same feature.
This way we can handle the conflicts automatically without introducing
recursive dependencies.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move common variables and/or values to the package (variant) default.
Add additional values in variant packages if necessary. Remove further
duplicates by introducing new templates.
Remove the ANY_[HOSTAPD|SUPPLICANT_PROVIDERS]_PROVIDERS. The are the
same as the variables without the any prefix. No need to maintain both
variables.
Signed-off-by: Mathias Kresin <dev@kresin.me>
procd needs processes to stay in foreground to remain under its gaze and
control. Failure to do so means service stop commands fail to actually
stop the process (procd doesn't think it's running 'cos the process has
exited already as part of its forking routing)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
As dnsmasq is started earlier than netifd usage of network.sh functions
at boottime will fail; therefore don't call at boottime the functions
which construct the dhcp pool/relay info.
As interface triggers are installed the dhcp pool/relay info will be
constructed when the interface gets reported as up by netifd.
At the same time also register interface triggers based on DHCP relay
config.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The pptp.so plugin needs to be built with -fPIC as well in order to be
linkable again.
Fixes 888a15ff83 ("ppp: add missing -fPIC to rp-pppoe.so CFLAGS")
Fixes e7397eef69 ("ppp: compile with LTO enabled")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Increase the termination timeout to 15s to let OpenVPN properly tear down
its connections, especially when weak links or complex down scripts are
involved.
Fixes FS#859.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Drop the parallel-unsafe custom Build/dtb macro and use the .dtb artifacts
produced by the generic image build code.
Also remove unused .dtb references in the mt7623 subtarget.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When attempting to use any of the functions in network.sh while netifd is
not started yet, the ubus interface dump query will fail with "Not found",
yielding an empty response.
Subsequently, jsonfilter is invoked with an empty string instead of a valid
JSON document, causing it to emit a second "unexpected end of data" error.
This caused the dnsmasq init script to log the following errors during
early boot on some systems:
procd: /etc/rc.d/S19dnsmasq: Command failed: Not found.
procd: /etc/rc.d/S19dnsmasq: Failed to parse json data: unexpected end of data.
Fix the issue by allowing the ubus query to fail with "Not found" but still
logging other failures, and by passing an empty JSON object to jsonfilter
if the interface status cache is empty.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
F9K1115v2 has a kernel partition size of 1408 kB.
Since kernel 4.9.x+ the kernel image for this device compiled had exceeded
the kernel partition size limit and thus failing size check.
The kernel image generated for this device
under ar71xx tiny target is 1329.67 kB < 1408 kB.
Signed-off-by: Kin Chan <kcchan1@outlook.com>
Some HP Thin clients use the broadcom nextreme chip as integrated NIC.
It is connected via PCI express and will only be found automatically if
phy-broadcom is loaded before tg3. This small change makes the thin
client usable for Freifunk with gluon out of the box.
Signed-off-by: Steffen Förster <steffen@chemnitz.freifunk.net>
We can safely assume by now that rpm5.org is dead and isn't coming back
so just add another mirror instead.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
This patch adds support for the MikroTik RB931-2nD (hAP mini):
https://mikrotik.com/product/RB931-2nD
Specifications:
* SoC: Qualcomm QCA9533 (650MHz)
* RAM: 32MiB
* Storage: 16MiB SPI NOR flash
* Ethernet: 3x100M
* Wireless: QCA9533 built-in, dual-chain 802.11b/g/n
Installation:
1. Setup a DHCP/BOOTP Server with the following parameters:
* DHCP-Option 66 (TFTP server name): pointing to a local TFTP
server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
of the to be booted image. The usable intramfs files are:
- openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
- openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
- openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
2. Press the reset button on the board and keep that pressed.
3. Connect the board to your local network via its Internet port.
4. Release the button after the LEDs on the board are turned off.
Now the board should load and start the initramfs image from
the TFTP server.
5. Now connect the board via either of its LAN ports (2 or 3).
6. Upload the sysupgrade image to the board with scp:
$ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin
7. Log in to the running system listening on 192.168.1.1 via ssh
as root (without password):
$ ssh root@192.168.1.1
8. Flash the uploaded firmware file from the ssh session via the
sysupgrade command:
root@OpenWrt:~# sysupgrade /tmp/fw.bin
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
'In different versions of coreboot are different names of apu boardname.
No need to check boardname to load module.'
Signed-off-by: Lukas Mrtvy <lukas.mrtvy@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
SOC: BCM63168 (BMIPS4350 V8.0 @400MHz)
Flash size: 16 MiB
RAM size: 128 MiB
Heavily based on patch for OpenWRT Chaos Chalmer.
Original patch and more info can be found at:
https://openwrt.org/toh/sky/sr102
Known issues:
- Wireless and ADSL modem are not working.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" could very
well fix the freezes that have been reported on the forum by
@ticerex and @takimata.
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/46>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Bump to the latest cake recipe.
This backports tc class support to kernel 4.9 and other than conditional
kernel compilation pre-processor macros represents the cake that has
gone upstream into kernel 4.19. Loud cheer!
Fun may be had by changing cake tin classification for packets on
ingress. e.g.
tc filter add dev ifb4eth0 parent 800b: protocol ip u32 match \
ip dport 6981 0xffff action skbedit priority 800b:1
Where 800b: represents the filter handle for the ifb obtained by 'tc
qdisc' and the 1 from 800b:1 represents the cake tin number. So the
above example puts all incoming packets destined for port 6981 into the
BULK (lowest priority) tin.
f39ab9a Obey tin_order for tc filter classifiers
1e2473f Clean up after latest backport.
82531d0 Reorder includes to fix out of tree compilation
52cbc00 Code style cleanup
6cdb496 Fix argument order for NL_SET_ERR_MSG_ATTR()
cab17b6 Remove duplicate call to qdisc_watchdog_init()
71c7991 Merge branch 'backport-classful'
32aa7fb Fix compilation on Linux 4.9
9f8fe7a Fix compilation on Linux 4.14
ceab7a3 Rework filter classification
aad5436 Fixed version of class stats
be1c549 Add cake-specific class stats
483399d Use tin_order for class dumps
80dc129 Add class dumping
0c8e6c1 Fix dropping when using filters
c220493 Add the minimum class ops
5ed54d2 Start implementing tc filter/class support
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Override the default shutdown action (stop) and close all processes
of dropbear
Since commit 498fe85, the stop action only closes the process
that's listening for new connections, maintaining the ones with
existing clients.
This poses a problem when restarting or shutting-down a device,
because the connections with existing SSH clients, like OpenSSH,
are not properly closed, causing them to hang.
This situation can be avoided by closing all dropbear processes when
shutting-down the system, which closes properly the connections with
current clients.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
[Luis: Rework commit message]
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
First of all lengths should be compared after checking all blocks for
being good/bad. It's because requested length may differ from a final
one if there were some bad blocks.
Secondly it makes sense to also compare crc32 since we already have a
new one calculated.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix broken DHCPv6 servers which provide the server unicast option but
do not reply on DHCPv6 renew messages directed to the IPv6 address
contained in the server unicast option whihc results in broken IPv6
connectivity.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Reading MTD data with (p)read doesn't return any error when accessing
bad block. As the result, with current code, CRC32 covers "data" stored
in bad blocks.
That behavior doesn't match CFE's one (bootloader simply skips bad
blocks) and may result in:
1) Invalid CRC32
2) CFE refusing to boot firmware with a following error:
Boot program checksum is invalid
Fix that problem by checking every block before reading its content.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
On Debian, busybox does have a time applet, but it does not support the -f
flag. Catch this in prereq check to give users to proper error message.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
An incorrect variable name was referenced in KERNEL_FILE_DEPENDS, leading
to the omission of the backport-* patch dirs in the generation of the
prepared stamp name.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The code has some remaining issues that cause ethernet hangs, so
disable it for now until we can get it fixed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
08719b1 mt76: use a per rx queue page fragment cache
4d2c565 mt76x2: reset HW before probe
f622975 mt76x2: fix CCK protection control frame rate
6780375 mt76x2: add frame protection support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allow enabling/commenting/disabling each feed individually by using a
tristate config symbol.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
