- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42180
* atm module needs to be loaded before linux-atm
* use absolute firmware paths
* extended validation
* add a script for mounting an optional firmware partition
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40460
These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.
Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 40329
This patch adds almost full support for this board.
- WiFi is still not working
- USB will not power up. According to some reports, it may be a passive port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40319
This patch adds almost full support for this board. WiFi is still not working.
The FXS ports are not functional due to missing support for the TAPI driver on
VR9 SoC.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40317
Arcadyan ARV4510PW has already a build profile in OpenWrt, but it is
severely lacking. This patch brings it up-to-date.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 39230
The switch is renamed to "switch0" in newer (3.10) linux kernels.
Configure the switch using vlans by default and only configure
the physical switch ports that are present.
Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38673
*) can not connect to switch chip
*) only one usb port is working
*) wifi is not working
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37712
On linux 3.8 the switch is named as "switch0", but the network configuration script names it as "eth0", causing no communication over ethernet due to no proper VLAN config.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 36782
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36781
This reassigns the PPPoE status to the LED that was intended to indicate
it, rather than the DSL sync light.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36777
user-space support for extracting the EEPROM for the RaLink WiFi is still
missing. Besides this, it's all working.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 35990
The VLAN mapping on the ARV4520PW board is the following:
port on Router: | VLAN in software:
LAN 1 | 3
LAN 2 | 2
LAN 3 | 1
LAN 4 | 0
DSL | 4
So LAN4 is not VLAN4 but VLAN0 (VLAN4 is DSL port) -> set "3 2 1 0 5t" as default switch config.
SVN-Revision: 31391
With this patch it is possible to generate uboot environment config file
inside lantiq target. Currently it is only supporting GIGASX76X board.
uboot environment config is used by fw_printenv fw_setenv tools.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 30537
* fixes leds
* adds all leds found on the sx763 board
* removes board_config from flash layout because wireless data is stored in kernel (ath5k)
* fix button handling
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 29763
