Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.
This patch makes all boards use the first method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46244
This device is identical to the TL-WR740N v5, it even uses the same HWID (which
wasn't the case for older TL-WR741ND revisions).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46238
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
rocket-m titanium is a device based on ar9344 with 802.11af poe.
It doesn't use the SoC wifi, instead it's using an ar9280 connected to
the pci bus. The gps version of the rocket-m ti is working, but
gps is untested. The gps is connected to the first serial port.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 46234
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46206
r45954 ("ar71xx: fix 100/10mbps ethernet link issues on mynet range
extender") introduced a pdata based modification of the tx_clk_dly. But it
was not checked if pdata actually existed. This caused a page fault on all
devices which didn't have at803x_platform_data specified for an at803x
based device.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46200
Update firmware name and md5sum. MAC-address location remains
unchanged from previous version.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46196
- it should be BOARDNAME instead of BOARD_NAME
- kernel partition should be padded to 1536k (somehow this padding was lost in translation to BuildCode in bc797c73f6328941b2194d144385655ad9297e7c)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46193
EPG5000 uses ath79 nvram functions, but does not select it. This breaks
build if no other board support enabling nvram support is selected.
Closes#19952.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46190
r46161 updated headers also touched by it, so it needed to be refreshed
as well.
Closes#20033.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46165
TP-Link ships wr740n v5.0 to Romania (so probably everywhere except
China) with 4 MB flash and 32 MB memory (confirmed by their local
support). This patch adds support for the v5.0 clone of v4, i just
tested it on my own v5.0 router and it works.
Signed-off-by: Daniel Petre <daniel.petre@posteo.net>
SVN-Revision: 46115
The hardware should be almost the same as TL-WR720N-v3. WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>". Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46046
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
Some devices ship with NAND images that use BCH ECC. Let the driver know
about that ECC mode so that it can be selected by machine files.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
SVN-Revision: 46022
It seems that there are maximum timings for mdio accesses that can be
hit when the system is under load and the thread is scheduled during
a read or write access. Since there is no way of knowing if this
happens as there is not even a parity bit, try to work around it
by disabling interrupts during any gpio-mdio accesses.
Performance impact seems to be neglectable, as mdio accesses are not
that often.
Hopefully fixes#19500.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46012
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
This patch adds the pll_1000 value for eth0 interface. This makes the Rocket M
XW image compatible with other Ubiquiti devices with similar hardware with a
Gigabit Ethernet port.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45965
In new firmware-4.bin (for ath10k) mac offset is 0x114 (276), not 0x118 (280).
This also closes#19751, bug introduced in #45624
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 45958
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.
The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.
The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.
Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 45954
They are useless, as the platform already selects the right options for
NAND support. The main reason for removing them is the fact that it
makes kernel configs more annoying to maintain on platforms that provide
NAND drivers but disable them (e.g. ramips)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45919
The v1 identifies as v10 internally. As there is no TL-WA830RE v10, add a
workaround to avoid confusing users.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45903
Building the loader in Image/Build/TPLINK-SAFELOADER would break the image
builder as no target compiler is available in that stage.
Fixes#19580
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45855
In contrast to Image/BuildLoader, Image/BuildLoaderPatched first patches the
kernel command line in the image and then builds the loader without command
line. This allows building loaders for systems which don't boot correctly when
the kernel command line is provided by the loader (like the TP-LINK CPE series).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45854
