Some devices out there only have a NOR flash to store the rootfs on.
While using UBI is arguable on this kind of flash, this is something that should
be supported.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44260
It fails to build because of missing of_irq_parse_raw and incompatible
irq_create_of_mapping.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44230
Replace the now defunct 062-mips_decompressor_build_fix.patch with another
patch that simply undefines the arch memset and memcpy defines to avoid
syntax errors in the redeclaration.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44223
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
Changeset r43049 removed the "062-mips_decompressor_build_fix.patch" which is
still required to properly build the xburst kernel.
Fix the syntax error in the preprocessed code by explicitely undefining the
"memcpy" and "memset" macros prior to declaring the replacements functions.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44133
Add global read-only swconfig attribute "arl_table" to display the
address resolution table.
So far the chip-specific part is implemented for AR8327/AR8337 only
as I don't have the datasheets for the other AR8XXX chips.
Successfully tested on TL-WDR4300 (AR8327rev2)
and TL-WDR4900 (AR8327rev4).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44104
Until a few years ago the page switch wait time was set to msleep(1)
what was changed to usleep_range(1000, 2000) later.
I can not imagine that a low-level operation like switching page
on register level takes so much time.
Most likely the value of 1ms was initially set to check whether
it fixes an issue and then remained w/o further checking whether
also a smaller value would be sufficient.
Now the wait time is set to 5us and I successfully tested this on
AR8327. IMHO 5us should be plenty of time for all supported chips.
However I couldn't test this due to missing hardware.
If other chips should need a longer wait time we can add the
wait time as a parameter to the ar8xxx_chip struct.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44103
Check for switch port link changes and
- flush ATU in case of a change
- report link change via syslog
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44102
The functionality to flush the address translation table contains two bugs
which luckily compensate each other.
1. Just setting the operation is not sufficient to perform the flushing.
The "active" bit needs to be set to actually trigger an action.
For the vtu operations this is implemented correctly.
2. ar8xxx_phy_read_status is called every 2s by the phy state machine
to check for link changes. This would have caused an ATU flush
every 2s.
Fix the chip-specific ATU flush functions and remove the ATU flush call
from ar8xxx_phy_read_status.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44101
Somewhere in the conversion of the MIPS architecture code to Device Tree
usage, there's been a failure to keep the separate variables holding the
kernel command line reconciled between the tree and the bootloader. This
patch restores previous functionality that broke.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44030
The swconfig get_link attribute (at least) on AR8327/AR8337 doesn't
consider the autonegotiated flow control.
AR8327/AR8337 provide the info about autonegotiated rx/tx flow control
in bits 10 and 11 of the port status register.
Use these values to display info about autonegotiated rx/tx flow
control as part of the get_link attribute.
Successfully tested on TL-WDR4900 (AR8327 rev.4) and
TL-WDR4300 (AR8327 rev.2).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44023
AR8327/AR8337 allow to read the result of EEE autonegotiation.
If EEE is autonegotiated between the link partners, display
this as part of the swconfig get_link attribute.
eee100: 100MBit EEE supported by both link partners
eee1000: 1GBit EEE supported by both link partners
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44022
Users reported network issues with AR8327 which turned out to be caused
by EEE not working correctly with certain link partners (ticket 14597).
The workaround was to disable EEE on all ports (changeset 41577).
The issue was with certain link partners only, therefore this patch
allows to control usage of EEE per port via swconfig.
Still the default is to initially disable EEE on all ports.
Successfully tested on a TL-WDR4900 (AR8327 rev.4)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44021
Since the driver doesn't know anything about (M)STP
we just hard-set the ports to be enabled if they are
part of the VLAN.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43938
- eliminate MV_CPUPORT; not necessary since we define
the CPU port(s) via Device Tree
- add STU and expand VTU operations
- update register names to match those of 88E61xx rather than
mvswitch's 88E6060
- use more consistent formatting
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43937
Move all AR8327/AR8337-specific driver code into a separate source file
ar8327.c and adjust patches so that ar8327.c is compiled if
CONFIG_AR8216_PHY is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43845
Move several structure definitions and #defines from ar8216.c
to ar8216.h and move AR8327/AR8337 header stuff into a new
header file ar8327.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43844
modules build during the kernel compile phase are ignored anyway,
all modules should be built using KernelPackage in
package/kernel/linux/modules/*
selecting the appropriate config symbols there rather than in
target/linux/*/config-*
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43842
The following patches unfortunately didn't hit the kernel stable
branches yet, therefore cherrypicking them for OpenWRT here:
* bridge: fix netfilter/NF_BR_LOCAL_OUT for own, locally generated queries
* bridge: multicast: enable snooping on general queries only
* bridge: multicast: add sanity check for general query destination
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 43841
accidentally #if was used instead of #ifdef, thus gcc warned
about CONFIG_ATA_LEDS being undefined...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43786
Remove read/write/rmw member functions from ar8xxx_priv
There seems to be no real benefit of the ar8xxx_priv member functions
read/write/rmw as one implementation exists for each of them only.
Especially ar8xxx_mii_rmw is assigned to priv->rmw first and then
mapped to ar8xxx_rmw.
Rename the ar8xxx_mii_.. functions to ar8xxx_.. and use them directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43742
Create helpers mii_read32 / mii_write32 for 32 bit MII ops.
Rename r3 variable to page in ar8xxx_mii_write to make it consistent
with the other ar8xxx_mii_xxxx functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43741
Factor out chip-specific parameters from ar8xxx_probe_switch.
Move the ar8xxx_chip definitions after the swops definitions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43740
This will allow us to drop it in the future. This patch doesn't change
the final mtdpart.c, it remains the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43696
This brings ssb and bcma to wireless-testing tag master-2014-12-05
In addition it also adds the ARM-BCM5301X-Add-IRQs-to-Broadcom-s-bus-
axi-in-DTS-f.patch which adds the irq number in a way it is done in the
mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43544
This is a swconfig driver for the Marvell 88E6171 switch,
which is a 7-port GigE switch with two CPU ports and 64
802.1q VLANs.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43486
Factor out set_mirror_regs to ar8xxx_chip.
Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43468
Factor out info whether switch should be configured at probe stage
to ar8xxx_chip. Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43466
This patch introduces some code that is compiled in whenever
CONFIG_BRIDGE_NETFILTER is built, with the code called from code compiled under
CONFIG_BRIDGE, CONFIG_BRIDGE_IGMP_SNOOPING or CONFIG_BRIDGE_NF_EBTABLES.
Unfortunately, these options aren't setting explicitly the dependency they now
have on CONFIG_BRIDGE_NETFILTER, for obvious reasons for CONFIG_BRIDGE.
However, this is not working really well when CONFIG_BRIDGE_NETFILTER is built
as a module, since code statically compiled will now use a function that is not
in the kernel image, which makes the linker grumpy.
Solve this by removing the option to build CONFIG_BRIDGE_NETFILTER as a module,
and protect our function definition by an IS_BUILTIN instead of a IS_ENABLED
macro. This fixes the issue for CONFIG_BRIDGE and CONFIG_BRIDGE_IGMP_SNOOPING.
Fixing CONFIG_BRIDGE_NF_EBTABLES has to be handled a bit differently, since it
directly references a variable that will not be declared if
CONFIG_BRIDGE_NETFILTER is not set. Protect the variable affectations by an
ifdef to make sure this doesn't happen.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43419
Patch reverts 43332 which seems to cause issues with VLAN functionality.
Add a specific check to check whether ANEG is still enabled and re-enable
it if necessary. Disable generic phy soft reset for kernel >=3.16.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43356
We should make sure that also for ar8216 hw gets initialized.
For ar8216 hw_init is a dummy currently. The hw_init used for ar8236
should be generic enough to be usable with ar8216 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43334
Move the PHY fixup call to the PHY init loop.
Use ar8xxx_has_gige in the PHY init instead of passing the gigE
capability via function parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43333
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43332
PHY init code in the switch-specific hw_init functions is mainly
identical. Factor it out into a generic ar8xxx_phy_init function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43331
Move phy fixup code from the chip-specific hw_init functions into a
fixup_phys callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43330
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43329
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43328
Without this patch the UBIFS driver is unable to attach to the mtd
storage and mount the root FS.
Fixes a kernel panic with Netgear WNDR4300/3700v4 devices.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43287
The patch adding AR8216_PHY_LEDS was not ported to more recent kernel
versions.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43139
Some changes from the header file were not ported from older kernel.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43137
The select SYS_HAS_DMA_OPS in CPU_CAVIUM_OCTEON was from the kernel
patch in 3.13, but it is only included in kernel 3.14 and not in 3.13
and 3.18, add it again.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43134
OpenWRT patch 255-lib80211_kconfig_hacks gives user possiblity to select
LIB80211 dependant settings (LIB80211_CRYPT_*) without having LIB80211
selected which is wrong.
My patch changes OpenWRT patch so LIB80211 is vissible and all
LIB80211_CRYPT_* options selects LIB80211 automatically.
Signed-off-by: Tomasz Wasiak <tjwasiak@gmail.com>
SVN-Revision: 43112
Boards that have more than one swconfig enabled switch will show the devices in
reverse order when call swconfig list. Fix this by using list_add_tail().
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43106
All platforms which are using 3.10.x at the moment are upgraded.
Changelogs:
https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.50https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.51https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.52https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.53https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.54https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.55https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.56https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.57https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.58
A new symbol 'X86_16BIT' appeared in 3.10.52 with commit 34273f41d57ee8d854dcd2a1d754cbb546cb548f
("x86-espfix-make-it-possible-to-disable-16-bit-support.patch")
I defaults to 'unset', but it's worth a discussion to enable it
("turn off support for any 16-bit software").
Also removed the patch 0db3db45f5bd6df4bdc03bbd5dec672e16164c4e
("fix build failure on memcpy() in decompress.c")
and is obsolete by commit 29593fd5a8149462ed6fad0d522234facdaee6c8 upstream.
included in kernel 3.10.56
compile tested on all platforms with:
make tools/install
make toolchain/install
make target/linux/compile
user@box:~/user/openwrt$ cat /tmp/log.txt
[Wed Oct 22 00:36:02 CEST 2014] ./smoketest.sh: ar71xx - OK
[Wed Oct 22 00:53:22 CEST 2014] ./smoketest.sh: ar7 - OK
[Wed Oct 22 01:08:27 CEST 2014] ./smoketest.sh: au1000 - OK
[Wed Oct 22 01:21:43 CEST 2014] ./smoketest.sh: avr32 - OK
[Wed Oct 22 01:37:47 CEST 2014] ./smoketest.sh: cns21xx - OK
[Wed Oct 22 01:52:05 CEST 2014] ./smoketest.sh: cns3xxx - OK
[Wed Oct 22 02:10:23 CEST 2014] ./smoketest.sh: gemini - OK
[Wed Oct 22 02:29:07 CEST 2014] ./smoketest.sh: ixp4xx - OK
[Wed Oct 22 02:44:01 CEST 2014] ./smoketest.sh: malta - OK
[Wed Oct 22 02:55:57 CEST 2014] ./smoketest.sh: mpc85xx - OK
[Wed Oct 22 03:07:56 CEST 2014] ./smoketest.sh: orion - OK
[Wed Oct 22 03:24:30 CEST 2014] ./smoketest.sh: ppc40x - OK
[Wed Oct 22 03:40:19 CEST 2014] ./smoketest.sh: ppc44x - OK
[Wed Oct 22 03:55:29 CEST 2014] ./smoketest.sh: realview - OK
[Wed Oct 22 04:09:47 CEST 2014] ./smoketest.sh: sparc - OK
[Wed Oct 22 04:23:37 CEST 2014] ./smoketest.sh: x86 - OK
[Wed Oct 22 04:35:56 CEST 2014] ./smoketest.sh: xburst - OK
run tested on x86, au1000, ar71xx, mpc85xx and brcm47xx
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43049
This is required due to 306-mips_mem_functions_performance.patch, just
add a memmove() implementation to satisfy the lzma2 decompressor code.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43036
This enables dedicated "rootfs" splitter by default. We still keep
CONFIG_MTD_SPLIT_SQUASHFS_ROOT, so the old (built-in) splitter will be
used as a fallback in case of problems.
Once we decide the dedicated partitioner works stable, we should remove
the old one completely.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42805
