Remove 131-MIPS-export-get_c0_perfcount_int.patch which was already applied
in 4.1.6. This fixes the following build error:
arch/mips/ath79/setup.c:217:77: error: redefinition of '__kstrtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:77: note: previous definition of '__kstrtab_get_c0_perfcount_int' was here
arch/mips/ath79/setup.c:217:350: error: redefinition of '__ksymtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:350: note: previous definition of '__ksymtab_get_c0_perfcount_int' was here
scripts/Makefile.build:258: recipe for target 'arch/mips/ath79/setup.o' failed
Reported-by: swalker
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46715
Properly treat -ENOSYS as no PHY, else ehci-orion won't work without
generic phy support.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46711
This also clears any bootloader-set FDB defaults. This had
caused issues creating port-based VLANs when mappings
overlapped previous VLANs. Packets destined to a port
not in the default port group flooded all ports.
Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC)
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46699
no-op since 2.6.35
removed in Kernel 4.1
see https://lwn.net/Articles/380931/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46671
The "linux,part-probe" dts parsing is a pretty neat generic feature.
It has been posted to kernel.org and could easily be reused by all
targets.
This change moves the patch to the 3.18 and 4.1 generic folders, and
makes the feature available to all platforms who may want to use it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46654
In addition to the update this also fixes compile problems with kernel 4.1.
This closes#20323.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46609
This patch was missing for kernel 4.0 and 4.1 in r46464. I also
replaced the version in OpenWrt with the version which went upstream
into the Linux mainline kernel.
This closes#20193 and #20192
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46493
REGMAP_MMIO is a hidden symbol, so it cannot be directly selected. If nothing
selects it, it will fail the build with:
ERROR: module '/store/buildbot/slave/slave/rb532/build/build_dir/target-mipsel_mips32_musl-1.1.10/linux-rb532/linux-3.18.19/drivers/base/regmap/regmap-mmio.ko' is missing.
make[2]: *** [/store/buildbot/slave/slave/rb532/build/bin/rb532/packages/base/kmod-regmap_3.18.19-1_rb532.ipk] Error 1
Fix this by adding a description to allow selecting it manually.
Fixes: r46451 ("kmod-regmap: enable MMIO support")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46485
NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.
This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position) and an E3372 device (which mandates NDP
to be after indexed datagrams).
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46464
If a link goes down, don't flush the complete ARL table.
Only flush the entries for the respective port.
Don't touch ARL table if a link goes up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46381
Adds functions for flushing ARL table entries per port.
Successfully tested on AR8327. Implementation for AR8216/AR8236/AR8316
is based on the AR8236 datasheet and assumes that the three chips
share a common ATU register layout.
Compile-tested only for AR8216/AR8236/AR8316.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46380
Adds the chip-specific part of reading ARL table for AR8216/AR8236/AR8316.
It's based on the AR8236 datasheet and compile-tested only as I couldn't
find datasheets for AR8216/AR8316 and don't own devices with these chips.
The existing ar8216_atu_flush implementation was used for all three
chip types, therefore I guess they share a common ATU register layout.
More testing would be appreciated.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46379
To improve reproducibility, prevent the inclusion of timestamps
in the gzip header.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 46361
The mips reloc patch introduced new allocations which were done before
add_unformed_module but never freed them in case of an error. A new hook in
Linux 3.19 called module_arch_freeing_init can be used for freeing memory
which were allocated during this init phase.
The problem can be seen when trying to load a module (via busybox insmod)
when it was already loaded.
free -m
for i in `seq 1 100`; do
/sbin/insmod /lib/modules/*/ath9k.ko >& /dev/null
done
free -m
This simple loop would leak ~3.2 MB.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46247
Backport for the Spansion S25FL164K
It's a 8 MiB flash chip with 4 KiB erase sectors.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46237
This is useful if the device also has an ethernet WAN interface with a
separate mac address (that is derived from the LAN mac address).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46220
Some machtypes were dropped when 4.0 support was added, and the
incomplete patch was taken over to 4.1.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46187
Code calling fpu_emulator_cop1Handler will pass on fault_addr, making gcc
complain about it not being initialized when the FPU emulator is disabled.
Fixes:
arch/mips/kernel/traps.c: In function 'do_fpe':
arch/mips/kernel/traps.c:864:22: error: 'fault_addr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
process_fpemu_return(sig, fault_addr, fcr31);
^
arch/mips/kernel/traps.c: In function 'do_ri':
arch/mips/kernel/traps.c:806:22: error: 'fault_addr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
process_fpemu_return(sig, fault_addr, fcr31);
^
arch/mips/kernel/traps.c:763:15: note: 'fault_addr' was declared here
void __user *fault_addr;
^
arch/mips/kernel/traps.c: In function 'do_cpu':
arch/mips/kernel/traps.c:1421:28: error: 'fault_addr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (!process_fpemu_return(sig, fault_addr, fcr31) && !err)
^
cc1: all warnings being treated as errors
make[7]: *** [arch/mips/kernel/traps.o] Error 1
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46184
The position of the nvram header file on brcm47xx changed with kernel
version 4.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46170
Make some network uapi headers detect if they are included after
not only glibc but also musl headers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46161
Boot tested: http://pastebin.com/L6aAb9xj
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo:
update to 4.1 final
add patches added since submission
delete patches applied in later rcs
restore commit messages in 220-gc-sections and 304-mips_disable_fpu
fix 050-backport_netfilter_rtcache to match new API
update inlined dma ops with upstream changes
add missing config symbols
enabled CONFIG_MULTIUSER
update kmod defintions for 4.1
]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46112
On two tested devices: Netgear R6250 (BCM53011 rev 2) and Luxul XWC-1000
(BCM53011 rev 3) it was possible to use port 7 and eth1 (instead of port
5 and eth0). It seems BCM53011 just like BCM53012 has 8 ports and
usually 3 of them are connected to the SoC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46104
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
On device reset the sizes for the vlan and port tables were wrongly
calculated based on the pointer size instead of the struct size. This
causes buffer overruns on 64 bit targets, resulting in panics.
Fix this by dereferencing the pointers.
Reported-by: Fedor Konstantinov <blmink@mink.su>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45938
At least on my b53 chip, the mask is 3 bits wide, and because
of this some STP states are not set properly and discarded when read.
Maybe for some other chips it makes sense to have just 2 bits width,
but I don't have other versions around to test/validate.
If that's the case then maybe we could add another STP state mask.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45937
STMMAC_PLATFORM and STMMAC_PCI have been added recently in the kernel,
but show up only when STMMAC driver is enabled. So se'll add it in the
generic config, so the kernel build doesn't stall whenever we enable
this driver.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45828
With this patch the following two patches are backported:
* bridge: fix parsing of MLDv2 reports
* bridge: allow setting hash_max + multicast_router if interface is down
The former one is an important fix which got just applied to the net-tree
and is queued for stable. The latter is a patch which is needed to make
the hash_max and multicast_router attributes configurable through
netifd.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 45783
Update kernel sources and refresh some patches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45761
Commit 5168c9a5702648eb690d32ec821647aca80aeba9 introduced a regression
during patch application on the 4.0 kernel. Some of the patched content
doesn't match the actual code, therefore leading to the following error:
Applying patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch
patching file net/ipv6/ip6_output.c
Hunk #1 FAILED at 886.
1 out of 1 hunk FAILED -- rejects in file net/ipv6/ip6_output.c
patching file net/ipv6/route.c
Hunk #1 succeeded at 2247 (offset 2 lines).
Patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch does not apply (enforce with -f)
This change just adapts the actual patch to fix what is in kernel 4.0
and make it apply cleanly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45705
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45676
Since the kernel/rootfs split handling was modified 2 years ago by r37283 (
https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins,
users have seen rather scary mtd errors in the log at every boot. The message
ends "-- forcing read-only", which looks a bit error-like. That error has
been mentioned in some forum threads, when users have noticed this message
instead of some actual error.
[ 2.940000] 0x000000070000-0x000000ff0000 : "firmware"
[ 2.970000] 2 netgear-fw partitions found on MTD device firmware
[ 2.970000] 0x000000070000-0x000000188440 : "kernel"
[ 2.980000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 2.990000] 0x000000188440-0x000000ff0000 : "rootfs"
The patch removes the rather useless warning message.
signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45669
This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45658
I still need to test following patch before backporting:
bgmac: leave interrupts disabled as long as there is work to do
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45571
Linux 4.0 was released on 2014-04-12
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45559
-removed symbol because it should be handled by wpan.mk
-add missing FAKEHARD symbol (this symbol is removed in Kernel 4.0)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45530
Refresh patches to remove the trailing whitespaces caused by an old
diffutils version on osx.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45506
it has been non-functional for years and caused numerous memleaks and
crashes for people that tried to enable it.
it has no maintained upstream source, and it does not look like it's
going to be fixed any time soon
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45423
On BCM5301X there are two different cases to handle: CPU port 8 vs. any
other one. Support for CPU port 8 was already partially implemented but
it lacked setting some extra bit for 2G speed. It also will need to be
extended to implement "SMP dual core 3 GMAC setup". That's the reason
for handling it in separated code block.
This patch also adds overriding CPU port state for port other than 8. It
requires using recently defined GMII_PORT registers.
It was tested for regressions on BCM53011 revs 2 & 3. It was also
confirmed to fix switch on some internal Broadcom board.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45402
It currently does not seem to make a difference anymore, except by
increasing compressed kernel image size
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45385
* properly enclose macro arguments in paranthesis on use
* remove trailing white space
* convert C99 // comments
* add missing blank lines after declaration
* remove braces from single statement blocks
* split lines > 80 chars (except for one)
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45356
These missing options have been noticed while enabling the following
configuration options on ipq806x, but they're available in the standard
kernel:
*ARCH_QCOM
*CONFIG_USB_SUPPORT
*CONFIG_USB_DWC3
*CONFIG_MFD_SYSCON
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45256
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2: changes in input.mk broke the patch, some of the CONFIG_SND_*
stuff was added already
SVN-Revision: 45205
Enabling this option renames the bootloader supplied root=
and rootfstype= variables, which might have to be know but
would break the automatisms OpenWrt uses.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45196
Use the latest version of the yaffs code. Fetched from the
yaffs2 git tree and it is based on the following commit:
commit 7e5cf0fa1b694f835cdc184a8395b229fa29f9ae
Author: Charles Manning <cdhmanning@gmail.com>
Date: Thu Aug 7 11:25:05 2014 +1200
yaffs-direct: Basic tests. Add lpthread flag for background gc support
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45188
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44969
