Refactor mesh initialization into a separate function, do some cleaning
on the way to make the code more readable.
Changes:
* Move iw mesh setup to new mac80211_setup_mesh()
* fallback on 'ssid' parameter in case 'mesh_id' isn't set
* move setting of freq variable to shared code as it is needed for
both, the wpa_supplicant and the iw based setup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The max_oper_chwidth settings was parsed incorrectly for big endian system.
This prevented the system to switch to VHT80 (or VHT160). Instead they were
mapped to:
* HT20: 20MHz
* VHT20: 20MHz
* HT40: 40MHz
* VHT40: 40MHz
* VHT80: 40MHz
* VHT160: 40MHz
This happened because each max_oper_chwidth setting in the config file was
parsed as "0" instead of the actual value.
Fixes: a4322eba2b ("hostapd: fix encrypted mesh channel settings")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
The commit 574e4377fa ("mac80211: properly setup mesh interface") uses
the variable $wpa to decide whether encrypted meshpoint is requested by the
user or not. But the variable $wpa will only be set correctly after the
function wireless_vif_parse_encryption is called.
Fixes: 574e4377fa ("mac80211: properly setup mesh interface")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.
Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)
Flash instruction:
Apply factory image via web-gui.
Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
b45e162 helpers: fix the set_helper in the rule structure
f742ba7 helpers.conf: support also tcp in the CT sip helper
08b2c61 helpers: make the proto field as a list rather than one option
Signed-off-by: John Crispin <john@phrozen.org>
Setup wpa_supplicant for encrypted mesh or when using DFS channels and
adjust interface setup to pass fixed frequency for mesh mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix encrypted (or DFS) AP+MESH interface combination in a way similar
to how it's done for AP+STA and fix netifd shell script.
Refresh patches while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
8206219 uci: fix memory leak in rpc_uci_replace_savedir()
10f7878 exec: close stdout and stderr streams on child signal
92d0d75 uci: use correct sort index when reordering sections
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6b4a340 version: bump snapshot
faa2103 compat: don't clear header bits on RHEL
4014532 compat: handle RHEL 7.5's recent backports
66589bc queueing: preserve pfmemalloc header bit
37f114a chacha20poly1305: make gcc 8.1 happy
926caae socket: use skb_put_data
724d979 wg-quick: preliminary support for go implementation
c454c26 allowedips: simplify arithmetic
71d44be allowedips: produce better assembly with unsigned arithmetic
5e3532e allowedips: use native endian on lookup
856f105 allowedips: add selftest for allowedips_walk_by_peer
41df6d2 embeddable-wg-library: zero attribute padding
9a1bea6 keygen-html: add zip file example
f182b1a qemu: retry on 404 in wget for kernel.org race
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
We cannot depend on CONFIG_OF in the module definition context as this symbol
is not defined for OpenWrt menuconfig. Depend on the targets that appear to
need the kmod-of-mdio module instead.
The target dependency list may not be complete, it is based on the build
failures encountered by the build bots.
Fixes: dc629d9cf5 ("kernel: fix kmod-switch-rtl8366-smi dependency")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Refresh patches and backport upstream to current HEAD:
1f1873a Log warning on very large cachesize config, instead of truncating it.
0a496f0 Do unsolicited RAs for interfaces which appear after dnsmasq startup.
e27825b Fix logging in previous.
1f60a18 Retry SERVFAIL DNSSEC queries to a different server, if possible.
a0088e8 Handle query retry on REFUSED or SERVFAIL for DNSSEC-generated queries.
34e26e1 Retry query to other servers on receipt of SERVFAIL rcode.
6b17335 Add packet-dump debugging facility.
07ed585 Add logging for DNS error returns from upstream and local configuration.
0669ee7 Fix DHCP broken-ness when --no-ping AND --dhcp-sequential-ip are set.
f84e674 Be persistent with broken-upstream-DNSSEC warnings.
Compile & run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Right now interface.update events are sent out by netifd upon interface state,
route, address (lifetime), prefix lifetime changes.
Dnsmasq is only interested in interface state changes and currently adds an
interface trigger for all the "interface.*" events.
In combination with commit 23bba9cb33, which triggers a SIGHUP signal to dnsmasq,
IPv6 address/prefix lifetime changes on the wan will trigger dnsmasq reloads which
can become frequent in case of shorter lifetimes.
To avoid frequent dnsmasq reload, this patch adds specific interface triggers.
During dnsmasq init it loops dhcp uci section; if the value of the ignore option
is set to 0, then the corresponding interface trigger is not installed.
Otherwise, if the ignore option value is 1, then procd_add_interface_trigger is
called which adds the interface trigger.
Signed-off-by: hux <xinxing.huchn@gmail.com>
572735e4 Update manual pages
e8d693c3 Bump up version number to 1.32.0, LT revision to 30:2:16
f44dfcd9 Update AUTHORS
1f1b0d93 Update manual pages
ce8c749b Merge pull request #1173 from nghttp2/asio-client-sni
3e4f257b asio: Support client side SNI
86fab997 Upgrade neverbleed to the latest master
c3ecd445 Merge pull request #1171 from nghttp2/h2load-rate-and-duration
c65ca20a h2load: -r and --duration are mutually exclusive
a5c408c5 Ignore all input after calling session_terminate_session
06379b28 Fix treatment of padding
e04de48e Merge pull request #1162 from nghttp2/libressl
00964642 Use LIBRESSL_IN_USE instead of defined(LIBRESSL_VERSION_NUMBER)
8d0b4544 libressl 2.7 has X509_VERIFY_PARAM_*
d8a34131 libressl 2.7 has SSL_CTX_get0_certificate
5db17d0a Compile with libressl 2.7.2
1bf69b56 Define LIBRESSL_LEGACY_API and LIBRESSL_2_7_API
3febaef1 Bump up LT revision to 30:1:16 due to v1.31.1 release
b1bd6035 Fix frame handling
b48bcb21 examples: Use C style comment in .c files
6f3ce2c7 examples: Remove unused lambda capture
2f9121cf Merge branch 'Sp1l-Sp1l/allow-no-npn'
e65e7711 Add comment on #endif
636ef51b Fix compile error with -Wunused-function
400934e5 [PATCH] Allow building without NPN
4c3a3acf Merge pull request #1146 from vszakats/cmakestaticlib
9aa6002c Merge pull request #1144 from hellojaewon/master
f342260b cmake: add ENABLE_STATIC_LIB option to build static lib
a6dd4970 Fix typo
842509da Don't allow 101 HTTP status code because HTTP/2 removes HTTP Upgrade
4add618a Bump up version number to 1.32.0-DEV
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
No functional change. Code tidy ups.
735eaf2 Make sure we don't reallocate q->tins (we didn't anyway but his
really makes sure)
6c5ad6e Get rid of __GFP_NOWARN flag for memory allocation
2a37333 Don't need the wrapper for kvfree, and no need to check before calling it
2b1c631 Whitespace fix
7fe6e28 compat tidyup (for older kernel versions <4.4)
93b805c pedant tidy up superfluous semicolons on switch statements
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Point at github which is new, maintained location for igmpproxy.
Remove all patches as all have been upstreamed.
Closes FS#1456
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The init sccript for igmpproxy uses the option 'network' both as an interface name for fetching the l3_device name and for creating the firewall rules. This only works if the name of the network and firewall zone are identical.
This commit introduces a new option 'zone' for configuring the upstream and downstream firewall zones in order for the init script to create the required firewall rules automatically. When no such options are given, the init script falls back to not creating the firewall rules and the user can opt to create these manually.
Signed-off-by: Jaap Buurman <jaapbuurman@gmail.com>
fixed build error when external kernel is selected from menuconfig.
The patches present in target/linux/generic does not gets applied
to external kernel and build fails while compiling mac82011 &
regmap-core kernel modules. as a fix added check in Makefile for
CONFIG_EXTERNAL_KERNEL_TREE present or not.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Cake is bearing fruits of kernel upstreaming efforts.
diffserv-llt dropped. DSCP mapping paper died and no one using it.
ack-filter re-written & simplified
tc userspace & cake kmod netlink interface usage changed in non
backwards compatible way, thus this once requires tc & cake to be
in-step. Change due to upstream requirements.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Bearing fruits of the latest upstreaming efforts on cake.
Changes: diffserv-llt dropped. The paper describing this DSCP
allocation has gone stale and doesn't appear used.
The userspace to kernel netlink messages for cake have been reworked in
a backwards incompatible way, so tc & cake must be bumped together this
once.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
print_uint() will silently promote its variable type to uint64_t, but there
is nothing that ensures that the format string specifier passed along with
it fits (and the function name suggest to pass "%u").
Fix this by changing print_uint() to use a native 'unsigned int' type, and
introduce a separate print_u64() function for printing 64-bit values. All
call sites that were actually printing 64-bit values using print_uint() are
converted to use print_u64() instead.
Since print_int() was already using native int types, just add a
print_s64() to match, but don't convert any call sites.
Fixes wonkyness in some stats from some qdiscs under tc
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This target aims to replace ar71xx mid-term. The big part that is still
missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik
subtargets will follow.
Signed-off-by: John Crispin <john@phrozen.org>
These modules usually require some special arguments to customize the
emulated device and they should be loaded manually by users.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
1. able to set neon flags to sama5d2 & sama5d4 subtargets.
2. fix the make clean which removes all the subtargets in bin folder.
3. able to configure kernel specific to subtarget.
4. able to set vfpu4 flags to samad3 subtargets.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
fixed DTC command not found error while compling uboot-at91. The fix
is to set DTC PATH in uboot-at91 MAKE command.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
fetching uboot src from linux4sam/u-boot-at91 github for all at91
target.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
updating to new version v3.8.10 and copying at91bootstrap.bin to bin folder.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add hotplug handle script for storage devices,
this will add corresponding option in the
/etc/config/samba file automatically.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Update to latest version of iproute2, refresh patches.
See https://lkml.org/lkml/2018/4/2/349 for a full overview of the
changes in 4.16.
Build and tested on AR7xxx against musl
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Currently, the build system uses an openwrt mirror which does not currently
work and FTP can be unreliable under several circumstances. This change
implicitly allows using all the mirrors to download.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Some options' default values have been changed upstream, others were
accidentally inverted (CONFIG_WOLFSSL_HAS_DES3). Also add options
needed to build hostapd/wpa_supplicant against wolfssl.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There is no usecase for not protecting symlinks that I know of in OpenWrt.
Not even on desktop systems where you have multiple users with a shell.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
527e700 ustream-ssl: Remove RC4 from ciphersuite in server mode.
39a6ce2 ustream-ssl: Enable ECDHE with OpenSSL.
45ac930 remove polarssl support
Signed-off-by: John Crispin <john@phrozen.org>
Without this patch the extra LDFLAGS of objects were selected based on the
name of the extension being built, which breaks for aggregate so builds.
Signed-off-by: John Crispin <john@phrozen.org>
Switched download from SourceForge to GitHub. It seems the author migrated to that.
Also fixed the website URL as the SourceForge link is dead.
Compile tested on ar71xx and mvebu. Small size decrease on ar71xx: 30444 vs. 30099 bytes.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When libressl was linked the libpthread was missing, add it in addition.
Also make the mxsimage tool to use the OpenSSL 1.1 API for the recent
libressl version.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
010-fix-rpmatch.patch is upstream, removed from our patchset
The file structure is changed, modify patch accordingly
use CONFIGURE_ARGS to disable tests, xattr and lzo
Compile and run tested on mvebu and x86_64
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This allows us to link the other tools against our libz and we do not
need the system zlib any more.
Only the static linked library is copied to the staging directory so we
have a statically linked library on all systems and not only on Linux.
This also adds the new dependencies of the packages which are depending
on zlib.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Choose first running interface, rather than first "up" interface (Redhat #1403025)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Added for convenience. These boards can be used as dev boards running
various operating systems from different media, and this simplifies work
with U-Boot environment.
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.
We switched to the upstream board-2.bin, hence the files can be removed
here.
Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
4136529 dhcpv6-ia: keep tentative assignments alive for a short time
200cc8f dhcpv6-ia: make assignment lookup more strict
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This patch was revised upstream before being merged, and OpenWrt's copy
was never updated to reflect the revision.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
[refreshed patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
7cc2668 version: bump snapshot
860c7c7 poly1305: do not place constants in different sections
5f1e4ca compat: remove unused dev_recursion_level backport
7e4b991 blake2s: remove unused helper
13225fc send: simplify skb_padding with nice macro
a1525bf send: account for route-based MTU
bbb2fde wg-quick: account for specified fwmark in auto routing mode
c452105 qemu: bump default version
dbe5223 version: bump snapshot
1d3ef31 chacha20poly1305: put magic constant behind macro
cdc164c chacha20poly1305: add self tests from wycheproof
1060e54 curve25519: add self tests from wycheproof
0e1e127 wg-quick.8: fix typo
2b06b8e curve25519: precomp const correctness
8102664 curve25519: memzero in batches
1f54c43 curve25519: use cmov instead of xor for cswap
fa5326f curve25519: use precomp implementation instead of sandy2x
9b19328 compat: support OpenSUSE 15
3102d28 compat: silence warning on frankenkernels
8f64c61 compat: stable kernels are now receiving b87b619
62127f9 wg-quick: hide errors on save
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Import two patches from Peter Oh to allow setting channel
bandwidth in the way it already works for managed interfaces.
This fixes mesh interfaces on 802.11ac devices always coming up in
VHT80 mode.
Add a patch to allow HT40 also on 2.4GHz if noscan option is set, which
also skips secondary channel scan just like noscan works in AP mode.
This time also make sure to add all files to the patch before
committing it...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When a partition offset is given, it is used in an lseek call, which
affects write, but not erase. Add it to the offset for erase calls as
well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Import two patches from Peter Oh to allow setting channel
bandwidth in the way it already works for managed interfaces.
This fixes mesh interfaces on 802.11ac devices always coming up in
VHT80 mode.
Add a patch to allow HT40 also on 2.4GHz if noscan option is set, which
also skips secondary channel scan just like noscan works in AP mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Before this commit, devices supporting both 2.4GHz and 5GHz would be
configured for 2.4GHz by default - unless they have VHT capabilities.
With this commit, channel 36 is only set when the frequency is supported.
VHT isn't checked unless that is the case.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Pipe uqmi output from qmi_wds_stop function into /dev/null.
This will supress the following output in proto teardown.
netifd: wwan (x): "No effect"
netifd: wwan (x): Command failed: Permission denied
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Several changes has been made:
+ AES support has been removed by
upstream commit c6831c7 (2017-11-14)
[remove patch "200-fw_env_no_aes.patch"]
+ Support for UBI volumes has beed added by
upstream commit 34255b9 (2017-11-15)
[remove patch "300-support-env-in-ubivol-chardev.patch"]
+ A command line argument has beed added ("-c") to manually indicate
the location of the environment configuration file
Also, patch "400-u-boot-2015.10-stdint.patch" is no longer
necessary, and the config option to enable UBI support has
been removed.
Size comparisons:
fw_printenv size:
Target Before After
ar71xx 15,189 bytes 18,133 bytes (+2,944 bytes)
ipq40xx 20,873 bytes 20,987 bytes (+114 bytes)
mvebu 20,881 bytes 20,991 bytes (+110 bytes)
ramips 15,128 bytes 18,072 bytes (+2,944 bytes)
OPKG package size:
Target Before After
ar71xx 11,309 bytes 12,875 bytes (+1,566 bytes)
ipq40xx 11,772 bytes 13,299 bytes (+1,527 bytes)
mvebu 11,609 bytes 13,114 bytes (+1,505 bytes)
ramips 10,975 bytes 12,503 bytes (+1,528 bytes)
Compile tested: ipq40xx (musl, glibc, gcc5-musl), ar71xx, mvebu, ramips
Run tested: ipq40xx (ASUS RT-AC58U)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
mbedtls changed in version 2.7.0 the soversion of the libmbedcrypto.so
library, all applications using this shared library have to be
recompiled to be able to load the new library.
Some binaries got rebuild to for the 2.7.0 release and are now using
libmbedcrypto.so.1, the older ones are still using libmbedcrypto.so.0.
Fixes: 75c5ab4ca ("mbedtls: update to version 2.7.0")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
bughost.org hasn't existed for 6-8 years, add a couple of current
mirrors to avoid the fallback to http://mirror2.openwrt.org/sources/.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
bughost.org hasn't existed for 6-8 years, add a couple of current
mirrors to avoid the fallback to http://mirror2.openwrt.org/sources/.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The missing dependency causes build problems on systems without PCI
support.
The ath10k_pci kernel module depends on PCI support so this dependency
should be added. ath10k now also supported the ahb interface on the
IPQ4019 SoC, but this SoC also has PCI support so this extra dependency
is not as problem.
Fixes: d0f3dd5b9f ("ath10k-ct: update to latest version, enable AHB.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Merge upstream patch from Sathishkumar Muruganandam
<murugana@codeaurora.org> for OpenWrt's backports package:
https://lkml.kernel.org/r/<1522049641-19521-1-git-send-email-murugana@codeaurora.org>
Commit-ID: 606204bb863fa3b0bb54929d79b4dc46338f9180
* FW has Smart Logging feature enabled by default for detecting failures
* and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.
*
* Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
* EVENT processing yet, suppressing the unknown event ID warning by moving
* this under ATH10K_DBG_WMI.
*
* Simulated the same issue by having associated STA powered off when
* ping flood was running from AP backbone. This triggerd STA KICKOUT
* in AP followed by FATAL CONDITION event 36925.
*
* Issue was reproduced and verified in below DUT
* ------------------------------------------------
* AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
*
* Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
When CONFIG_PM was not set rsi_sdio_reinit_device() was not compiled
into the driver but referenced.
This is a backport form the mainline Linux kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RedPine RS9113 wireless module requires rsi91x driver to be built
and linux-firmware/rsi/rs9113_wlan_qspi.rps to be installed.
Also we add patch for successful compilation of rsi91x driver.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
For unencrypted mesh networks our scripts take care of setting
the various mesh_param values. wpa_supplicant changes somes of them
when being used for SAE encrypted mesh and previously didn't allow
configuring any of them. Add support for setting mesh_fwding (which
has to be set to 0 when using other routing protocols on top of
802.11s) and update our script to pass the value to wpa_supplicant.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 1356a66f94.
The change breaks wpa_supplicant.conf generation, more work is needed
to fix mesh+AP.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Our commands setting accept_ra to 0 on all interfaces got lost in the
transition to procd. This remained unnoticed for a long time, as we also
enable forwarding on all interfaces, which prevents RA handling by default.
Restore the commands, while also fixing a possible race condition in the
old version.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
e243683 libfstools: move mount points when switching to JFFS2
3782b59 libfstools: add "const" to char pointer arguments in mount_move()
79721f0 libfstools: fix foreachdir() to pass dir with a trailing slash
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
513eb27 system-linux: check ioctl return value in system_vlan()
df1625d system-linux: check ioctl return value in system_if_flags()
209c508 system-linux: fix segfault on alloc failure in system_if_check()
4a8e20e system-linux: fix segfault on error in system_add_ip6_tunnel()
36e4700 handler: fix resource leak on error in netifd_init_script_handlers()
86a0e7c system-linux: remove unnecessary open call in system_if_dump_info()
1e2cf67 system-linux: fix memory leak on error in system_add_vxlan()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
1d23142 mt76: add led active low to debugfs
549f43b mt7603: ensure that the ACK flag is set for A-MPDUs with any acked subframe
df9f9f6 mt7603: always try tx rate1 first
9c52f36 mt7603: pull the final rate index from the status descriptor
f36f308 mt7603: improve validation of rx frames
9a23989 mt7603: remove warning on rx with invalid channel info
7a31731 mt76: check for pending reset before attempting to schedule tx
873a7c9 mt7603: call mt76_txq_schedule_all as a barrier to prevent tx during reset
d9e5da3 mt76: add rcu locking in tid reorder function
a8e8921 mt7603: add more checks to avoid dereferencing invalid pointers in wcid lookup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Let's use /etc/sysctl.d for package-provided snippets and leave
/etc/sysctl.conf to the admin. Don't backup /etc/sysctl.d on upgrades, so
old defaults get replaced properly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
We can use /etc/sysctl.d/* for package-supplied sysctl snippets, giving
admins the option to use /etc/sysctl.conf to override settings.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
11_migrate-sysctl has not been updated with new file hashes since 2012.
Let's get rid of it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This firmware has only small changes from the last commit, but
it does have an important fix for at least some PTK rekey logic.
The old firmware would have issues if the driver managed to set
a clear key while encryption was 'enabled'. This new firmware for
both wave-1 and wave-2 should not be susceptible to this type of
bug any more.
And remove mesh-bcast IE flag from wave-2, still need more work before
we can enable that flag in ath10k-ct firmware it seems.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Don't select the firmware with the board file, it prevents an easy use
of the -ct ath10k firmware. Select the firmware within the default
packages instead.
Remove the per device selection of the firmware now that it the
firmware is selected by default.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
Unlike when operating in Ad-Hoc mode, we apparently need to pass the
hostapd control socket interface to wpa_supplicant when using 802.11s
mesh mode.
There also seems to still be something wrong with the logic setting
channel and (v)htmode parameters...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
And import patchset to allow 802.11s mesh on DFS channels, see also
http://lists.infradead.org/pipermail/hostap/2018-April/038418.html
Fix sae_password for encryption mesh (sent upstream as well).
Also refreshed existing patches and fixed 463-add-mcast_rate-to-11s.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2e783b227766 ebt_ip: add support for matching IGMP type
b5fbb8d786c9 ebt_ip: add support for matching ICMP type and code
c5e5b784fd1a Move ICMP type handling functions from ebt_ip6 to useful_functions.c
11da52177196 include: sync linux/netfilter_bridge/ebt_ip.h with kernel
Note: the new features require at least kernel 4.17 or backported patches.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The serial was working before, but not when doing copy&pasting longer
commands in a short time.
Fixes: a4def18f29 ("uboot-omap: Update to u-boot v2017.01")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Split physdev match out of ipt-extra to allow installing ipt-extra without
pulling in br-netfilter.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
While ebtables can be combined with br-netfilter, there is no good reason
to make it a dependency.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
kmod-br-netfilter is not only a support module, but can be useful on its
own, using the net.bridge.bridge-nf-call-* sysctls.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Non-selecting dependencies easily lead to Kconfig failures due to recursive
dependencies. We hit such an issue in Gluon; the easiest fix is to make
the dependency selecting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
RFC6771 does not exclude the forwarding of the example domain as it
states : "Caching DNS servers SHOULD NOT recognize example names as
special and SHOULD resolve them normally."
Example domains cannot be assigned to any user or person by DNS
registrars as they're registered in perpetuity to IANA meaning
they can be resolved; therefore let's remove the example domains
from the rfc6761.conf file.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
42a8ecd jshn: fix format string for int64 type
92009b7 utils: ensure that byte-order conversion functions evaluate the argument only once
ace6489 switch from typeof to the more portable __typeof__
Signed-off-by: Felix Fietkau <nbd@nbd.name>
42a8ecd jshn: fix format string for int64 type
92009b7 utils: ensure that byte-order conversion functions evaluate the argument only once
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bug fix release. 1.28.3 has fixes for
* ash and hush (do not leave stray open file destriptors in children),
* cpio (fix for symlink extraction),
* grep ("grep -Fw a" was matching "aa").
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
74b5a3 script: fix possible negative delay
473f248 dhcpv6: always trigger script update in case of IA updates
ea18935 ra: rework route information option handling
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Some packages are already using $(1)/var on package install.
On multiuser systems this breaks the build when multiple
users build OpenWrt.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This reverts commit 4fb684a755.
The compile fixes are still required for host systems using GCC 5.x,
such as Ubuntu 16.04 LTS.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It's intentional that some boards within a target don't have all LEDs
which are tried to be setup in a common script. Don't show a warning in
such cases.
Fixes: 4f4fc993db ("base-files: add more name source to get_dt_led helper function")
Signed-off-by: Mathias Kresin <dev@kresin.me>
It seems both issues (GCC5 and Musl) were fixed at some point. Thus, they can be dropped.
Did not bump version as there is no change in functionality or size.
Compile-tested on ar71xx and mvebu, both with musl.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
flash_erase utility allows to erase MTD partitions on NAND flash.
Useful when you want to clean or write an MTD partition from scratch.
e.g., before using kobs-ng to flashing SPL images it's recommended
to erase the MTD partition to ensure it's empty.
Signed-off-by: Adrià Llaudet <adria.llaudet@gmail.com>
Update busybox to 1.28.2, refresh patches and default config.
* modify 230-add_nslookup_lede.patch as opt_complementary was removed
Also move nslookup_longopts variable declaration to be inside
the same conditional as the function itself.
* modify 250-date-k-flag.patch to match upstream (opt_complementary)
* remove 600-cve-2017-16544.patch that is upstreamed
Notes about config changes:
* Some applet-specific LONG_OPTIONS config options were removed
* Config help text indentation changed, caused lots of
text formatting changes for convert_menuconfig.pl
* convert_defaults.pl moved lots of defaults around, summary of
actual changes below
New applets/features:
---------------------
ARCH
HEXEDIT
MINIPS
NETCAT
NUKE
RESUME
RUN_INIT
SETFATTR
New options:
------------
FEATURE_CATN
FEATURE_CROND_SPECIAL_TIMES
FEATURE_LIBBUSYBOX_STATIC
FEATURE_SETPRIV_CAPABILITIES
FEATURE_SETPRIV_CAPABILITY_NAMES
FEATURE_SETPRIV_DUMP
FEATURE_SH_READ_FRAC
FEATURE_SWAPONOFF_LABEL
FEATURE_VOLUMEID_MINIX
FEATURE_XARGS_SUPPORT_ARGS_FILE
FEATURE_XARGS_SUPPORT_PARALLEL
HUSH_GETOPTS
HUSH_READONLY
HUSH_TIMES
Removed:
--------
FEATURE_HAVE_RPC
MSH
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This Adds fixes for the following security problems based on debians patches:
CVE-2016-2125: Unconditional privilege delegation to Kerberos servers in trusted realms
CVE-2017-12163: Server memory information leak over SMB1
CVE-2017-12150: SMB1/2/3 connections may not require signing where they should
CVE-2018-1050: Denial of Service Attack on external print server.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These functions are not declared in any header file and only used in
same compile unit, mark them as static to remove one gcc warning and
make it easier for the compiler to optimize them out.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes some minor security problems.
Old size:
162262 bin/packages/mips_24kc/base/libmbedtls_2.7.0-1_mips_24kc.ipk
New size:
163162 bin/packages/mips_24kc/base/libmbedtls_2.8.0-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This release brings various improvements to clearfog support, such as distro-boot.
Obsoletes:
0002-clearfog-reset-usom-onboard-1512-phy.patch
0003-clearfog-enable-distro-boot-code.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
CONFIG_* variables can easily be set by overriding Build/Configure.
so set NET_RANDOM_ETHADDR=y and CMD_SETEXPR=y here.
This replaces the following patches:
0001-clearfog-generate-random-MAC-address.patch
0004-clearfog-enable-setexpr-command-by-default.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Wave-1 firmware has a fix for 'addba' not finding the peer. Thanks to Hauke
for finding and reporting this.
Wave-2 firmware has a fix for leaking a peer multicast key when a monitor device
is created.
And I re-ordered the '4019' firmware images in the Makefile to match the order
of the others. No functional change for that reorder.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
This reverts commit 745d0e7f4b.
It looks like upstream don't want the patch so let's revert it here too.
I hope a fix from upstream is forthcoming.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Fix psidlen becomes negative in case embedded address bit lenght is smaller than
IPv4 suffix length.
While at it improve parameter checking making the code more logical and
easier to read.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
opkg currently has some issues with Provides and this change makes the
image builder fail because of that. Revert the change for now until opkg
is fixed
This reverts commit 092d75aa3e.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Changes since last version
dfb68f8 service: initialize supplementary group ids
3db4e6d service: add func for string config change check
c3faabe procd: get rid of putenv usage.
The supplementary group id change fixes FS#988
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The following patches were merged upstream:
000-hostapd-Avoid-key-reinstallation-in-FT-handshake.patch
replaced by commit 0e3bd7ac6
001-Prevent-reinstallation-of-an-already-in-use-group-ke.patch
replaced by commit cb5132bb3
002-Extend-protection-of-GTK-IGTK-reinstallation-of-WNM-.patch
replaced by commit 87e2db16b
003-Prevent-installation-of-an-all-zero-TK.patch
replaced by commit 53bb18cc8
004-Fix-PTK-rekeying-to-generate-a-new-ANonce.patch
replaced by commit 0adc9b28b
005-TDLS-Reject-TPK-TK-reconfiguration.patch
replaced by commit ff89af96e
006-WNM-Ignore-WNM-Sleep-Mode-Response-without-pending-r.patch
replaced by commit adae51f8b
007-FT-Do-not-allow-multiple-Reassociation-Response-fram.patch
replaced by commit 2a9c5217b
008-WPA-Extra-defense-against-PTK-reinstalls-in-4-way-ha.patch
replaced by commit a00e946c1
009-Clear-PMK-length-and-check-for-this-when-deriving-PT.patch
replaced by commit b488a1294
010-Optional-AP-side-workaround-for-key-reinstallation-a.patch
replaced by commit 6f234c1e2
011-Additional-consistentcy-checks-for-PTK-component-len.patch
replaced by commit a6ea66530
012-Clear-BSSID-information-in-supplicant-state-machine-.patch
replaced by commit c0fe5f125
013-WNM-Ignore-WNM-Sleep-Mode-Request-in-wnm_sleep_mode-.patch
replaced by commit 114f2830d
Some patches had to be modified to work with changed upstream source:
380-disable_ctrl_iface_mib.patch (adding more ifdef'ery)
plus some minor knits needed for other patches to apply which are not
worth being explicitely listed here.
For SAE key management in mesh mode, use the newly introduce
sae_password parameter instead of the psk parameter to also support
SAE keys which would fail the checks applied on the psk field (ie.
length and such). This fixes compatibility issues for users migrating
from authsae.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
5d2bf09 uci: fix a potential use-after-free in uci_set()
3b3d63e list: only record ordering deltas if element position changed
4c4d343 cmake: Fix cli shared linking against ubox
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Improve portability of init script by declaring resolvfile as local
in dnsmasq_stop function.
Fixes resolvfile being set for older busybox versions in dnsmasq_start
in a multi dnsmasq instance config when doing restart; this happens when
the last instance has a resolvfile configured while the first instance
being started has noresolv set to 1.
Base on a patch by "Phil"
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Cake in kernel space now splits stats structure handling across netlink
messages to reduce stack usage issue flagged by upstream kernel checks.
Update user space (tc) qdisc handling to understand this new regime.
Cake also reports packet overheads & compensation in a different way so
add display code for this. e.g.
'tc -s qdisc show dev eth0' reports this extra detail:
min/max transport layer size: 28 / 1500
min/max overhead-adjusted size: 65 / 1550
average transport hdr offset: 14
Cake also supports output in JSON format.
Patch is bulkier than before because a (slightly out of date - see above
stats) man page is included for reference. Better than nothing!
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Relevant changes:
0afc1be Fixes for kernel 4.16
d2d6780 Reinitialise overhead compensation stats when reconfiguring.
a3bab9d Export overhead compensation stats to userspace.
9cd2fa8 Split tin stats to its own structure to decrease size of tc_cake_xstats
71c7b44 Gather more statistics about packet length transformations.
0517357 Rework overhead compensation to use dynamic transport header offset instead of (inaccurate) static one.
c1a0c8e Refactor length handling code to better centralise overhead calculations
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
PKG_EXTMOD_SUBDIRS should be set to the sub directory where the kernel
module gets build in, for the ath10k-ct driver this changed in commit
3888e77c1c from ath10k to ath10k-4.13. Without this fix the depends
line of the ath10*.ko modules is empty and the kernel module load system
will not automatically load the depended modules like mac80211.
Fixes: 3888e77c1c ("ath10k-ct driver: use dma_alloc_coherent, 4.13 based driver")
Fixes: 23a388fe41 ("ath10k-ct: Force loading mac80211 and ath modules.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The HTT-MGT variants transport management frames over the
normal HTT tx path, just like data frames. This saves
limitted WMI buffers which can become depleted if lots of
management frames become stuck in TX queues due to peer
that went away.
In addition, at least for the wave-1 firmware, htt-mgt is
required in order for 802.11r (fast roaming) authentication
to function properly.
The htt-mgt firmware requires the use of the ath10k-ct
driver. Normal non-htt-mgt ath10k-ct firmware should work
with stock drivers.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This updates to latest ath10k-ct firmware. Hopefully we are
at the end of the development cycle for this firmware release,
so these should be stable.
wave-1 changes since last release:
Release 20
* Allow flushing peer when deleting. Hopefully this will allow the
peer delete command to happen in a reasonable amount of time even
if the RF environment is busy (or peer has died).
To enable this, set the high flag in the mac-addr second word in the
ath10k driver near end of the ath10k_wmi_op_gen_peer_delete method:
cmd->peer_macaddr.word1 |= __cpu_to_le32(0x80000000);
* Attempt to fix crash seen in resmgr-ocs, appearantly due to list corruption.
Use a temporary list instead of trying to rely on for-each-safe.
* Add flag to tx-descriptor to allow driver to request no-ack on data
frames. This is bit 15 on the flag1 field (previously un-used).
* Add option to support specifying the tx-rate-code and retry count on
a per-packet basis. Only a single series is supported at this time.
Useful mainly for radiotap monitor-tx type testing at this point.
* Fix crash on startup when chip is at -40 deg C and calibration fails. Instead
of asserting, just keep retrying calibration, which appears to start working
after a few minutes (when the chip warms up).
* Allow reporting per-chain rssi for management frames. We pack the values into
empty space in the mgt-frame wmi header. This will only be enabled if the driver
requests it, since otherwise the driver is assumed to not understand the new API.
ath10k-ct drivers that support this feature will automatically enable it.
* A customer reports a case that appears to be the hardware not properly detecting
end of AMPDU, so frames were being mis-delivered to the wrong peer. Attempt to
work around this, and in doing so, clean up a bunch of void* abuse in the block-ack
reordering code (could not ever confirm there was a problem in this area).
* Re-work the rx-mem logic to be less complicated and to use less memory.
* Attempt to fix crash that appearanty happens because the driver can sometimes
delete a vdev in 'up' state.
* Attempt to fix hung scan state machine issues.
* Fix crash in tx path due to un-initialized memory.
wave-2 changes since last release:
Release 10
* Fix an assert related to tx scheduling. This hopefully fixes
what appears to be a regression that I added some time back.
* Enable CSI reporting for 9984, and maybe 9888/9886. Only in
non-trimmed builds.
* Other stability improvements, including regression fixes from
some tricky bugs introduced in earlier releases.
* Allow compiling for IPQ4019 chipset.
* Firmware will now send txbf frames to the host (driver) if the
TXBF (0xF00000001) set-special feature is enabled, or when the radio
is in monitor mode. But, if the frame is consumed by the txbf_cv
logic, then the pkt cannot be delivered to the host in this manner. Instead,
a WMI event will be sent and host can find the txbf_cv data in shared
memory. See ath10k_wmi_event_txbf_cv_mesg() in ath10k-ct driver.
* Support rx-all-mgt option. When enabled, the firmware will deliver all
management frames that it can to the host. No RX filters are changed
when this option is enabled.
* Fix at least some problems with sending tx-beamforming frames to SU-MIMO
peers. Looks like this was a regression in my code.
* Fix a crash in rate-ctrl due to nss mismatch. This was something I introduced
while trying to fix other bugs in rate-ctrl some time back.
* Attempt to fix a sw-peer-key object leak in IBSS mode. The peer key code
is very complex, and shares some pointers as union members. I think I fixed
at least some of the issues, but would not be surprised if more exist.
* Improve ath10k user guide to document CT firmware features:
https://www.candelatech.com/ath10k-ug.php
* Add ct-special option to configure the txbf sounding time. See ath10k-ug.php
* Fix and allow the driver to tell the firmware to send sounding frames. See ath10k-ug.php
In further testing, this seems to fail much of the time, and I am not sure why.
Disabling this in diet (trimmed) builds.
* Fix crashes related to deleting peers while they are in power-save mode. Reported
by LEDE user on r7800 with 9984 NIC.
* Make rate-ctrl txbf probe work better. If enabled, the rate-ctrl logic will periodically
send out probes at an NSS that can to txbf. Previously, txbf probes would not reliably happen
if both AP and peer had the same nss (ie, 2x2 talking to 2x2). To enable this feature, you
need to enable the fwtest-cmdid number 20.
* Report rx-timeout error counters. These were previously un-reported, though the
field existed in the wmi struct already.
* txbf: Ignore frames not destined for us. If NIC is in promisc mode, it
could acquire and process NDPA frames that were not destined for it. Check
the dest-MAC and ignore frames not for us (pass them up the stack for monitor
mode instead of save them in the peer's rate-ctrl logic.)
* Port ping-pong crash handling and othe related features to IPQ4019 target. It should
now act similar to 9984 in this regard.
* Fix a few asserts related to txbf and tx-seq logic.
* Add custom-stats support, for rx-reorder-stats. Similar to what I did for wave-1.
* Disable AMSDU for IBSS. This now matches what I did for peregrine. It seems to
work better this way, though I did not debug it in detail.
* Enable the set-special command to re-enable AMSDU for IBSS if user wants to experiment.
* Fix bug where dbglog did not disable IRQs, so if you made dbglog messages from the IRQ
handler, it could cause corruption that could crash the firmware and/or corrupt the log
message buffers.
* Don't assert if there are no buffer descriptors for RX of non-data frame.
* Retry any stuck block-ack sessions every 20 seconds instead of just disabling BA for
ever when we get too many failures.
* Fix SGI flag when reporting tx-rate info. The flag moved since wave-1 days, and
I did not notice that when I ported my changes forward to wave-2.
* Allow disabling special CCA handling for IBSS txqs. Earlier testing indicated this
might improve throughput in some testing on 9984 chips in IBSS mode, but subsequent
testing looks about the same without it. Since I do not really understand what this
setting exists for, leave it at upstream defaults. A new set-special API command (0x12)
can be used to enable this hack for testing. Setting 0x1 bit disables special CCA handling
for non-beacon IBSS txqs, setting 0x2 bit disables it for beacon queues as well.
* Add MCAST-BCAST feature flag. This tells driver we do not need a monitor interface
to do MESH.
* When calculating the rx-address filter (affects ACK & BLOCK-ACK, among other things),
to not add in monitor interfaces if other interfaces are up. There is no need for
a monitor device to ACK frames.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Among other things, this will check for an htt-mgt variant of
ath10k-ct firmware before loading 'normal' firmware, and it disables
verbose printing of firmware DBGLOG messages by default.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Update DEPENDS and PROVIDES so that ath10k-ct firmware
and drivers can be used to replace stock firmware
and drivers. The -htt firmware variant, which requires
ath10k-ct driver now selects ath10k-ct driver when the
firmware is selected.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Drop providing the virtual package ip by busybox which was added in commit
1cec4d4ef0.
Letting busybox provide the virtual package ip is not optimal for the
following reasons :
- Applications depending on ip expect either the ip-full or
ip-tiny package to be enabled.
- Busybox ip applet cannot be added or removed at runtime
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The driver updates include:
ath10k driver backport to fix WPA 'pn' related security bugs
(4.13 based driver only currently),
a fix for off-channel TX for CT wave-1 firmware, a likely
fix for napi related crashes, and a backport of the firmware fetch
patch.
AHB is needed for the IPQ4019 platform radios.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[use common subject format]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[wigyori@uid0.hu: renamed to 221-compatible-old-dtc.patch from 220-]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
U-Boot now requires GCC > 5
Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.
Also move some options of patch 010 affecting the whole platform
to 010's device only.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
print_int used 'int' type internally, whereas print_uint used 'uint64_t'
These helper functions eventually call vfprintf(fp, fmt, args) which is
a variable argument list function and is dependent upon 'fmt' containing
correct information about the length of the passed arguments.
Unfortunately print_int v print_uint offered no clue to the programmer
that internally passed ints to print_uint were being promoted to 64bits,
thus the format passed in 'fmt' string vs the actual passed integer
could be different lengths. This is even more interesting on big endian
architectures where 'vfprintf' would be looking in the middle of an
int64 type. Symptoms of this included tc qdisc showing bizarre values
for a variety of fields across a variety of qdiscs (e.g. refcnt, flows,
quantum)
print_u/int now stick with native int size.
A similar patch has been sent upstream.
Fixes FS#1425
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
94b6878 Tidy crypto.c of old library compat. Now need libnettle 3.
8b96552 Fix compiler warning.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This callback should have one parameter less, this parameter is not used
so this was not a so big problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the UBOOT_MAKE_FLAGS defined in include/u-boot.mk and do not
overwrite them to compile the host tools against the shipped LibreSSL.
In addition add a patch to fix a compile problem when compiling the
tools against LibreSSL caused by differences in the API between OpenSSL
1.1 and LibreSSL.
This should fix the compile problems seen in build bot from time to time
by not depending on the host libssl-dev package any more but using the
LibreSSL version from OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mwlwifi was updated to a new stable. Included in this stable release are the
followin benefits:
- Fixed compiling for kernel 4.14
- Fixed crash on 88W8864 binary
Compiled and tested on: WRT3200ACM and WRT1900AC
Signed-off-by: Gabe Rodriguez <lifehacksback@gmail.com>
Option --client-cert-not-required DEPRECATED is deprecated in v2.4 and removed in OpenVPN 2.5.
Replaced by param --verify-client-cert none|optional|require in v2.4 see
https://community.openvpn.net/openvpn/wiki/ DeprecatedOptions#a--client-cert-not-required
Signed-off-by: Christian Bayer <cave@cavebeat.org>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_ RELEASE increase]
This patch adds support for Cisco Meraki MR33
hardware highlights:
SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT
NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable)
ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE
WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80
WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2
WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80
LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1)
1 x Orange LED Fault Indicator (shared with LP5562)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8
AT24C64 8KiB EEPROM
Kensington Lock
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
1x4 0.1" header with half-height/low profile pins.
The pinout is: VCC (little white arrow), RX, TX, GND.
Flashing needs a serial adaptor, as well as patched ubootwrite utility
(needs Little-Endian support). And a modified u-boot (enabled Ethernet).
Meraki's original u-boot source can be found in:
<https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427>
Add images to do an installation via bootloader:
0. open up the MR33 and connect the serial console.
1. start the 2nd stage bootloader transfer from client pc:
# ubootwrite.py --write=mr33-uboot.bin
(The ubootwrite tool will interrupt the boot-process and hence
it needs to listen for cues. If the connection is bad (due to
the low-profile pins), the tool can fail multiple times and in
weird ways. If you are not sure, just use a terminal program
and see what the device is doing there.
2. power on the MR33 (with ethernet + serial cables attached)
Warning: Make sure you do this in a private LAN that has
no connection to the internet.
- let it upload the u-boot this can take 250-300 seconds -
3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin
(the u-boot is listening on 192.168.1.1)
# tftp 192.168.1.1
binary
put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin
4. wait for it to reboot
5. connect to your MR33 via ssh on 192.168.1.1
For more detailed instructions, please take a look at the:
"Flashing Instructions for the MR33" PDF. This can be found
on the wiki: <https://openwrt.org/toh/meraki/mr33>
(A link to the mr33-uboot.bin + the modified ubootwrite is
also there)
Thanks to Jerome C. for sending an MR33 to Chris.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Not all LED driver are using the label devicetree property for the led
name. Add support for the TI/National Semiconductor LP55xx Led Drivers,
which are using the chan-name property for the led name, as fallback.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add a fucntion to get the a binary mac address from file. Use the new
function for mtd_get_mac_binary() to limit duplicate code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the patch that was posted to ath10k-devel ML:
<https://patchwork.kernel.org/patch/10233491/>
|From: Thomas Hebb <tommyhebb@gmail.com>
|Subject: [PATCH] ath10k: search all IEs for variant before falling back
|Date: Wed, 21 Feb 2018 11:43:39 -0500
|[...]
|This patch fixes the issue by first searching the entire file for the ID
|with variant, and searching for the fallback ID only if that search
|fails. It also includes some code cleanup in the area, as
|ath10k_core_fetch_board_data_api_n() no longer does its own string
|mangling to remove the variant from an ID, instead leaving that job to a
|new flag passed to ath10k_core_create_board_name().
|
|I've tested this patch on a QCA4019 and verified that the driver behaves
|correctly for 1) both fallback and variant BDFs present, 2) only fallback
|BDF present, and 3) no matching BDFs present.
|
|Fixes: 1657b8f84ed9 ("ath10k: search SMBIOS for OEM board file extension")
|Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Note: 937-ath10k-calibration-variant.patch has been reassigned a new 081
number, as it now ships with upstream.... But also because this patch
requires the change in ath10k_core_create_board_name().
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
libext2fs breaks krb5 by always installing its own copies of libcom_err.so
and libss.so.
Move the libraries into separate libcomerr and libss packages respectively
and add a host build recipe to stage the required compile_et and mk_cmds
utilities for use by other packages.
This allows the krb5 package to be fixed to use the system wide libcomerr
and libss libraries.
Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
[rename libcom_err to libcomerr, make compile_et and mk_cmds relocatable,
cleanup makefile, add dependency on host build, reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Backport the compiler support patches from upstream u-boot to this older
version to make it compile with GCC 7.
This was found by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support configuration in the form...
list ip6prefix 2001:db8:1234::/64
list ip6prefix 2001:db8:5678::/64
... to allow specifying multiple routed IPv6 prefixes.
Implements feature request FS#1361.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
1f5a29c ip: do not add local routes for host dependencies
c06f842 device: add support for setting the isolate options for bridge ports
69aeaab interface-ip: fix route selection for host dependencies
Signed-off-by: Felix Fietkau <nbd@nbd.name>
busybox tries to be smart and passes a number of additional flags to the
compiler. Unfortunately, the i386-specific flags break ABI compatiblity
with libc.
Fixes busybox crashes observed on x86-generic with GCC 7.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.
An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.
Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.
Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.
Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem
Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv
Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.
Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9984.
The update fixes "ath10k_pci 0001:01:00.0: Invalid VHT mcs 15 peer
stats" spamming the kernel ring buffer at very high frequencies, but
introduces the new "ath10k_pci 0001:01:00.0: Unknown eventid: 36925".
This new warning doesn't appear to cause problems in practice and is
only emitted relatively rarely, not causing dmesg to overflow within
minutes.
Tested on the ZyXEL NBG6817; early feedback also suggests this firmware
to work well (with the same fixes and caveats) on the Netgear r7800 as
well.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This patch updates ath10k-firmware to last commit and use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9888.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
392811a ubus: let fw3_ubus_address() return the number of resolved addresses
359adcf options: emit an empty address item when resolving networks fails
503db4a zones: disable masq when resolving of all masq_src or masq_dest items failed
f50a524 helpers: implement explicit CT helper assignment support
a3ef503 zones: allow per-table log control
8ef12cb iptables: fix possible NULL pointer access on constructing rule masks
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The default fragment low/high thresholds are 3 and 4 MB. On devices with
only 32MB RAM, these settings may lead to OOM when many fragments that
cannot be reassembled are received. Decrease fragment low/high thresholds
to 384 and 512 kB on devices with less than 64 MB RAM.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In addition to removing redundant code, this fixes various issues in
IB-generated images that have been fixed in prepare_rootfs before,
including better handling of CONFIG_CLEAN_IPKG and enabling of initscripts
from FILES.
We also reuse the opkg macro and remove --force-... flags that have been
removed from rootfs.mk as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Many packages use the opkg conffiles field to list configuration files that
are to be retained on upgrades. Make this work on systems without opkg.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The package still leaks some user space linker options into the kernel
space. This breaks the build when ASLR is activated, deactivate it for
now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
7c0d711 version: bump snapshot
b6a5cc0 contrib: add extract-handshakes kprobe example
37dc953 wg-quick: if resolvconf/run/iface exists, use it
1f9be19 wg-quick: if resolvconf/interface-order exists, use it
4d2d395 noise: align static_identity keys
14395d2 compat: use correct -include path
38c6d8f noise: fix function prototype
302d0c0 global: in gnu code, use un-underscored asm
ff4e06b messages: MESSAGE_TOTAL is unused
ea81962 crypto: read only after init
e35f409 Kconfig: require DST_CACHE explicitly
9d5baf7 Revert "contrib: keygen-html: rewrite in pure javascript"
6e09a46 contrib: keygen-html: rewrite in pure javascript
e0af0f4 compat: workaround netlink refcount bug
ec65415 contrib: embedded-wg-library: add key generation functions
06099b8 allowedips: fix comment style
ce04251 contrib: embedded-wg-library: add ability to add and del interfaces
7403191 queueing: skb_reset: mark as xnet
Changes:
* queueing: skb_reset: mark as xnet
This allows cgroups to classify packets.
* contrib: embedded-wg-library: add ability to add and del interfaces
* contrib: embedded-wg-library: add key generation functions
The embeddable library gains a few extra tricks, for people implementing
plugins for various network managers.
* crypto: read only after init
* allowedips: fix comment style
* messages: MESSAGE_TOTAL is unused
* global: in gnu code, use un-underscored asm
* noise: fix function prototype
Small cleanups.
* compat: workaround netlink refcount bug
An upstream refcounting bug meant that in certain situations it became
impossible to unload the module. So, we work around it in the compat code. The
problem has been fixed in 4.16.
* contrib: keygen-html: rewrite in pure javascript
* Revert "contrib: keygen-html: rewrite in pure javascript"
We nearly moved away from emscripten'ing the fiat32 code, but the resultant
floating point javascript was just too terrifying.
* Kconfig: require DST_CACHE explicitly
Required for certain frankenkernels.
* compat: use correct -include path
Fixes certain out-of-tree build systems.
* noise: align static_identity keys
Gives us better alignment of private keys.
* wg-quick: if resolvconf/interface-order exists, use it
* wg-quick: if resolvconf/run/iface exists, use it
Better compatibility with Debian's resolvconf.
* contrib: add extract-handshakes kprobe example
Small utility for extracting ephemeral key data from the kernel's memory.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (git log --oneline description)
6e744662 Update bash_completion
478eac09 Update manual pages
88e2029e Bump up version number to 1.31.0, LT revision to 30:0:16
45d76cf5 nghttpx: Close listening socket on graceful shutdown
54573f28 Merge pull request #1137 from nghttp2/session-set-user-data
17793e99 Add nghttp2_session_set_user_data() public API function
5eac3c90 Update manual pages
e70195ae nghttpx: Update doc
fe51e7fa Merge pull request #1130 from nghttp2/avoid-inet_pton-macro
eb951c2c src: Define nghttp2_inet_pton wrapper to avoid inet_pton macro
39f0ce7c Merge pull request #1126 from nghttp2/nghttpx-expired-client-cert
65157811 Merge pull request #1123 from nghttp2/mruby-client-cert-not-before-after
e8af7afc nghttpx: Add an option to accept expired client certificate
38abfd18 nghttpx: Add mruby tls_client_not_before, and tls_client_not_after
ff3edc09 nghttpx: Fix potential memory leak
0bb15406 Bump up version number to 1.31.0-DEV
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The lantiq components still leak some user space linker options into the
kernel space. This breaks with build when ASLR is activated, deactivate
it for now on these packages.
Fixes: FS#1391
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.
This decreases the size of the ipk file from 87589 bytes to 81267 bytes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not force to build with O3 optimization any more, but take what was
selected by the OpenWrt build system.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The build process does not leak the user space cflags into the kernel
build process any more, this allows to activate MIPS16 builds.
This was fixed with some update of ifxos.
This decreases size of the libifxos.a and the ltq-vdsl-app
old:
78320 libifxos.a
44383 ltq-vdsl-app_4.17.18.6-2_mips_24kc.ipk
new:
66852 libifxos.a
43506 ltq-vdsl-app_4.17.18.6-2_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The split-up into packages gre, grev4 and grev6 causes confusion for the
users as reported in FS#1399.
As IPv4 and IPv6 are considered now as bundled; squash the grev4 and grev6
packages into the gre package and let gre provide both grev4 and grev6.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Fixes the assumption the busybox udhcpc applet is always enabled; in case
the symbolic link check fails the DHCP shell handler script will exit and
as result the DHCP protocol handler will not be registered in netifd.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This is to simplify maintenance. It's easy to say now which patches need
some extra work and/or sending upstream. Updating to newer backports
should be also simpler with this.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit 79a768a90f.
Some devices can go over their power limits with this commit, so this
needs to be handled on a case by case basis instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There was a mismatch between indicating factory reset and code actually
starting it. After 5 seconds status LED started blinking rapidly letting
user know it's ready to release reset button. In practice button had to
stay pressed for another second in order to relly start the process.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Remove RPS/XPS support from netifd core, move the logic to a hotplug
script that uses a different policy which provides better performance
and more fairness across flows
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support config in the form of ....
add_list sendopts=router:10.10.10.2
add_list sendopts=nissrv:20.20.20.2
add_list sendopts=0x7D:abba
This allows to configure sendopts having white spaces as option value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
With this, `mount -t efivarfs` is available and tools such as efitools
and efibootmgr will be usable.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
[daniel@makrotopia.org: some whitespace fixes, match From: with SoB]
As each mvebu device only uses one of the firmwares provided by mwlwifi
package, it makes sense to put them in separate packages and only install
the one that is needed.
Current mwlwifi version's firmware sizes and usages by devices:
88W8864.bin 118776 caiman, mamba, cobra, shelby
88W8897.bin 489932 (none)
88W8964.bin 449420 rango
Changes by this commit:
* indicate in title that mwlwifi also is driver for 88W8897 and 88W8964
* remove mwlwifi package's firmware installation rules
* add 3 new individual firmware packages (all depends on kmod-mwlwifi):
- mwlwifi-firmware-88w8864
- mwlwifi-firmware-88w8897
- mwlwifi-firmware-88w8964
* add firmware package to mvebu devices' DEVICE_PACKAGES accordingly
Signed-off-by: Johnny S. Lee <_@jsl.io>
[Add the used FW files to the PACKAGES of default image]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allow building perf on uncommon targets again.
Depending on the kernel version, not all of these archs will actually use
libunwind in perf. Still, it seems simpler and less error-prone to use the
same list that is defined in the libunwind package.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Works around two incompatiblities between glibc and (POSIX-compliant) musl:
- missing register definitions from asm/ptrace.h
- non-POSIX-compliant ucontext_t on PPC32 with glibc
Compile tested on mpc85xx.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Support configuration in the form...
list ip6prefix 2001:db8:1234::/64
list ip6prefix 2001:db8:5678::/64
... to allow specifying multiple additional IPv6 prefixes.
Implements feature request FS#1361.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
As indicated in #5574 samba fails to build with linker error due to lack
of talloc_* functions when the packet libtalloc also gets build.
According to Makefile it is compiled with "--without-libtalloc" option.
Running ./configure --help shows that there is another option connected
to libtalloc: --enable/disable-external-libtalloc.
Adding this option fixes build.
Signed-off-by: Jakub Tymejczyk <jakub@tymejczyk.pl>
Remove this old patch which prevents showing the xfrm ports for SCTP
This was added in commit 60c1f0f64d ("finally move buildroot-ng to trunk")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
62d52e9 mt76: set RX_FLAG_DUP_VALIDATED for A-MPDU reordered packets
5ba5995 mt76x2: rework tx power handling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
459b6932 policy: add nft translation for simple policy none/strict use case
255e55b7 tests: xlate-test: no need to require superuser privileges
6990bbc5 extensions: hashlimit: remove space before burst in translation to nft
13ecaeb0 extensions: hashlimit: Rename 'flow table' keyword to meter
c252a2b0 extensions: Add test for cluster nft translation
bda1daa4 extensions: ip6t_{S,D}NAT: add more tests
88fa4543 extensions: ip6t_{S,D}NAT: multiple to-dst/to-src arguments not reported
64a0e098 extensions: libxt_cluster: Add translation to nft
6067208f extensions: add support for 'srh' match
0f387b07 extensions: hashlimit: fix incorrect burst in translations
1ffe6a74 extensions: libxt_hashlimit: Do not print default timeout and burst
27de281d extensions: Add macro _DEFAULT_SOURCE.
75364151 iptables: Remove const qualifier from struct option.
8b0da213 iptables: masquerade: add randomize-full support
e64db006 iptables: patch to correct linker flag sequence
033eac81 extensions: libxt_tcpmss: Add test case for invalid ranges.
505bfa11 iptables: xtables-eb: Remove const qualifier from struct option
a6d6821a iptables: extensions: Fix MARK target help
71de414c libxt_sctp: fix array out of range in print_chunk
1a32381a extensions: add tests for ipcomp protocol
4bd51770 tests: xlate: print output in same way as nft-test.py
d0e3d95f libxt_recent: Remove ineffective checks for info->name
23e6ed71 libxt_TOS: add tests for translation infrastructure
9564595e Update .gitignore
bebce197 iptables: iptables-compat translation for TCPMSS
dbbab0aa extensions: libxt_tcpmss: Detect invalid ranges
0e958281 iptables-translate: add test file for TCPMSS extension
de3c68b6 iptables-compat: do not allow to delete populated user define chains
f4b80ce7 iptables: change large file support handling
f5b46c2f iptables: Constify option struct
21ba5b38 ip{,6}tables-restore: Don't accept wait-interval without wait
60e0ffd3 ip{,6}tables-restore: Don't ignore missing wait-interval value
af468b6e utils: Add a man page for nfnl_osf
1773dcaa utils: nfnl_osf: Fix synopsis in help text
895ce096 extensions: libxt_bpf: fix missing __NR_bpf declaration
3c633296 xtables-compat-restore: fix translation of mangle's OUTPUT
1c32e560 netfilter: xt_hashlimit: add rate match mode
b5331f88 xtables-compat: fix memory leak when listing
91ae12e3 xtables-compat-restore: fix several memory leaks
79e1edd1 iptables-xml: Fix segfault on jump without a target
c49a93f1 xtables-translate: fix double space before comment
79fa7cc2 libip6t_icmp6: xlate: remove leftover space
8e62f572 tests: xlate: generalize owner
8d994bcf iptables: Add file output option to iptables-save
f8e5ebc5 iptables: Fix crash on malformed iptables-restore
80d8bfaa iptables: insist that the lock is held.
c29d99c8 libxtables: Display weird character warning for wildcards
1fe96cfb tests: xlate: check if it is being run as root
3f92b259 tests: xlate: remove python 3.5 dependency
d89dc47a iptables-restore/save: exit when given an unknown option
65801d02 iptables-restore.8: document -w/-W options
9cd3adbe iptables-restore/ip6tables-restore: add --version/-V argument
1ec1fb7a extensions: libxt_hashlimit: fix 64-bit printf formats
27f69f4a iptables: extensions: Remove typedef in struct.
340105fa tests: add regression tests for xtables-translate
b669e184 extensions: libxt_TOS: Add translation to nft
b2a84476 iptables: Remove unnecessary braces.
2963a8df iptables: Remove explicit static variables initalization.
1cf4ba6f iptables: Constify option struct
999eaa24 iptables-restore: support acquiring the lock.
6e2e169e iptables: remove duplicated argument parsing code
836846f0 iptables: move XT_LOCK_NAME from CFLAGS to config.h.
b91af533 iptables: set the path of the lock file via a configure option.
0e94eb2e iptables-translate: print nft iff there are more expanded rules to print
48ad179b libxtables: abolish AI_CANONNAME
9f50bbdf libxtables: remove unnecessary nesting from host_to_ip(6)addr
c6df55d6 iptables-translate: print nft command for each expand rules via dns names
82dacbb8 xtables-translate: Avoid querying the kernel
9f972f45 extensions: libxt_addrtype: Add translation to nft
2c8e251e utils: nfsynproxy: fix build with musl libc
9b8cb756 libiptc: don't set_changed() when checking rules with module jumps
eb66632d extensions: libxt_hashlimit: Add translation to nft
72bb3dbf xshared: using the blocking file lock request when we wait indefinitely
24f81746 xshared: do not lock again and again if "-w" option is not specified
fc3c3b4e libxt_hashlimit: add new unit test to catch kernel bug
516d9191 iptables: update pf.os
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This makes it possible to add an iptables rule that offloads routing/NAT
packet processing to a software fast path. This fast path is much
quicker than running packets through the regular tables/chains.
Requires Linux 4.14
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This only works with nftables for now, iptables support will be added
later. Includes a number of related upstream nftables improvements to
simplify backporting follow-up changes
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the auth or assoc request was denied the reason
was always WLAN_STATUS_UNSPECIFIED_FAILURE.
That's why for example the wpa supplicant was always
trying to reconnect to the AP.
Now it's possible to give reasoncodes why the auth
or assoc was denied.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add Wireless Network Management (IEEE 802.11v)
support to:
- hostapd-full
- wpa_supplicant-full
It must be enabled at runtime via UCI with:
- option ieee80211v '1'
Add UCI support for:
- time_advertisement
- time_zone
- wnm_sleep_mode
- bss_transition
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
Neighbor reports are enabled implicitly on use, beacon reports and BSS
transition management need to be enabled explicitly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is fixing multiple compile problems with kernel 4.14 and updates the
code to take care of changes introduced between kernel 4.9 and 4.14.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rename the gphy firmware to match the name requested by kernel 4.14 and
update the devicetree source files to use the new name.
Update the u-boot lantiq Makefile to be compatible with the new names as
well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With upstream commit 2c93e790e825 ("usb: add CONFIG_USB_PCI for system
have both PCI HW and non-PCI based USB HW") the CONFIG_USB_PCI was
introduced.
The option is disabled by default in our generic kernel 4.14 config, hence
we need to set the option for all related kernel modules.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With a9772285a724 ("linux/compiler.h: Split into compiler.h and
compiler_types.h") compiler.h was refactored and most its content was
moved to compiler_types.h. Both files are required to build ppp-mod-pppoa.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The current implementation only checked if uqmi itself executed
correctly which is also the case when the returned value is actually
an error.
Rework this, checking that CID is a numeric value, which can only
be true if uqmi itself also executed correctly.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
1721453 Remove special handling of A-for-A queries.
499d8dd Fix boundary for test introduced in 3e3f1029c9ec6c63e430ff51063a6301d4b2262
6f1cbfd Fix debian/readme typo.
55ecde7 Inotify: Ignore backup files created by editors
6b54d69 Make failure to chown() pidfile a warning.
246a31c Change ownership of pid file, to keep systemd happy.
83e4b73 Remove confusion between --user and --script-user.
6340ca7 Tweak heuristic for initial DNSSEC memory allocation.
baf553d Default min-port to 1024 to avoid reserved ports.
486bcd5 Simplify and correct bindtodevice().
be9a74d Close Debian bug for CVE-2017-15107.
ffcbc0f Example config typo fixes.
a969ba6 Special case NSEC processing for root DS record, to avoid spurious BOGUS.
f178172 Add homepage to Debian control file.
cd7df61 Fix DNSSEC validation errors introduced in 4fe6744a220eddd3f1749b40cac3dfc510787de6
c1a4e25 Try to be a little more clever at falling back to smaller DNS packet sizes.
4fe6744 DNSSEC fix for wildcard NSEC records. CVE-2017-15107 applies.
3bd4c47 Remove limit on length of command-line options.
98196c4 Typo fix.
22cd860 Allow more than one --bridge-interface option to refer to an interface.
3c973ad Use SIGINT (instead of overloading SIGHUP) to turn on DNSSEC time validation.
faaf306 Spelling fixes.
c7e6aea Change references to gPXE to iPXE. Development of EtherBoot gPXE was always development of iPXE core developer Michael Brown.
e541245 Handle duplicate RRs in DNSSEC validation.
84a01be Bump year in Debian copyright notice.
d1ced3a Update copyrights to 2018.
a6cee69 Fix exit code from dhcp_release6.
0039920 Severely fix code formating of contrib/lease-tools/dhcp_release6.c
39d8550 Run Debian startup regex in "C" locale.
ef3d137 Fix infinite retries in strict-order mode.
8c707e1 Make 373e91738929a3d416e6292e65824184ba8428a6 compile without DNSSEC.
373e917 Fix a6004d7f17687ac2455f724d0b57098c413f128d to cope with >256 RRs in answer section.
74f0f9a Commment language tweaks.
ed6bdb0 Man page typos.
c88af04 Modify doc.html to mention git-over-http is now available.
ae0187d Fix trust-anchor regexp in Debian init script.
0c50e3d Bump version in Debian package.
075366a Open inotify socket only when used.
8e8b2d6 Release notes update.
087eb76 Always return a SERVFAIL response to DNS queries with RD=0.
ebedcba Typo in printf format string added in 22dee512f3738f87539a79aeb52b9e670b3bd104
0954a97 Remove RSA/MD5 DNSSEC algorithm.
b77efc1 Tidy DNSSEC algorithm table use.
3b0cb34 Fix manpage which said ZSK but meant KSK.
aa6f832 Add a few DNS RRs to the table.
ad9c6f0 Add support for Ed25519 DNSSEC signature algorithm.
a6004d7 Fix caching logic for validated answers.
c366717 Tidy up add_resource_record() buffer size checks.
22dee51 Log DNS server max packet size reduction.
6fd5d79 Fix logic on EDNS0 headers.
9d6918d Use IP[V6]_UNICAST_IF socket option instead of SO_BINDTODEVICE for DNS.
a49c5c2 Fix search_servers() segfault with DNSSEC.
30858e3 Spaces in CNAME options break parsing.
Refresh patches.
Remove upstreamed patches:
250-Fix-infinite-retries-in-strict-order-mode.patch
260-dnssec-SIGINT.patch
270-dnssec-wildcards.patch
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The default receive window size in dropbear is hardcoded to 24576 byte
to limit memory usage. This value was chosen for 100Mbps networks, and
limits the throughput of scp on faster networks. It also severely limits
scp throughput on high-latency links.
Add an option to set the receive window size so that people can improve
performance without having to recompile dropbear.
Setting the window size to the highest value supported by dropbear
improves throughput from my build machine to an APU2 on the same LAN
from 7MB/s to 7.9MB/s, and to an APU2 over a link with ~65ms latency
from 320KB/s to 7.5MB/s.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Between mbedtls 2.6.0 and 2.7.0, the void returning mbedtls_MODULE* functions
were deprecated in favor of functions returning an int error code. Use
the new function mbedtls_sha256_ret().
Signed-off-by: Russell Senior <russell@personaltelco.net>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Between mbedtls 2.6.0 and 2.7.0, the void returning mbedtls_MODULE* functions
were deprecated in favor of functions returning an int error code. Use
the new function mbedtls_sha256_ret().
Signed-off-by: Russell Senior <russell@personaltelco.net>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This syncs the Orange Pi R1 device tree files with the one from the
upstream kernel and also uses the default configuration from the Orange
Pi Zero.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some functions used by a lot of other software was renamed and is only
active when deprecated functions are allowed, deactivate the removal of
deprecated functions for now.
Fixes: 75c5ab4caf ("mbedtls: update to version 2.7.0")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The PC Engines APU3b has a new nct5104b version with chip ID 0xc453.
This adds support for that version.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
This fixes the following security problems:
* CVE-2018-0488: Risk of remote code execution when truncated HMAC is enabled
* CVE-2018-0487: Risk of remote code execution when verifying RSASSA-PSS signatures
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for GL.iNet GL-B1300
Specification:
- SOC: IPQ4028 / QCA Dakota
- RAM: 256 MiB
- FLASH: 32 MiB
- ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT: one reset and one WPS button
- LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1
Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
192.168.1.2 have that file.
- the wifi led will be flashing when writing image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
128bc35 logread: fix reconnect logd logic
66347ec logread: move the code setting up the request blob out of the main loop
975a258 logread: move output connection setup code out of main loop
b81bea7 logread: cleanup pid file handling
d73e7d2 ubox: Replace strerror(errno) with %m format.
Signed-off-by: John Crispin <john@phrozen.org>
Some people reported problems with the current development version, so
go back to the latests more or less release.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Using PKG_SOURCE_DATE instead of PKG_VERSION will make the build system
generate the version based on the date and the git hash. This way the
tar file name changes when the git hash changes and this avoids problems
when someone forgets to change the version, but changes the git hash.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changes since last merge into OpenWrt since 2017-12-14:
- Added debugfs file tx_hist.
- Added debugfs file fixed_rate.
- Added debugfs file ba_hist.
- Modified the way to establish BA stream.
- Added code to control BF type.
- Added functions to check/dump dhcp packet.
- Upgrade 88W8964 firmware to 9.3.2.4.
- Added debugfs file coredump.
- Corrected the way to transmit multicast packets.
- Change driver version to 10.3.4.0-20180118.
- Corrected the way to get qos control.
- Assigned broadcast dhcpoffer to another queue.
- Separated broadcast and multicast packets. Bump to latest commit 20180206
Signed-off-by: Chris Breuer <github@chrisbreuer.de>
Make it easily possible to add a custom script in front of this hotplug
script which adds new devices. This is needed for the mvebu target in
which we want to migrate the old configuration before new devices are
getting detected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
D-Link DAP-1522 is a wireless bridge/access point with 4 LAN
ports and a dual-band wireless chipset.
Specifications:
- Ralink RT2880
- 32 MB of RAM
- 4 MB of Flash
- 4x 10/100/1000 Mbps Ethernet (RTL8366SR)
- 802.11abgn (RT2850)
Flash Instructions:
1. Download lede-ramips-rt288x-dap-1522-a1-squashfs-factory.bin
2. Open the web interface and upload the image
Signed-off-by: George Hopkins <george-hopkins@null.net>
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.
Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Karl Palsson <karlp@etactica.com>
uqmi contains a command for directly querying the modem if there
is a valid data connection, so let's use it.
This avoids the cases were all previous tests are succesful, but the
actual data link is not up for some reasons, leading to states were we
thought the link was up when it actually wasn't ..
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Originally, the implementation only checked if uqmi command
execution succeeded properly without actually checking it's returned data.
This lead to a pass, even when the returned data was indicating an error.
Rework the verification to actually check the returned data,
which can only be correct if the uqmi command itself also executed correctly.
On command execution success, value "pdh_" is a pure numeric value.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Debugging shows that using the general method properly cleans on each
run, while the method specifying the client-ID shows "No effect"
even while in connected state.
Fixes several connectivity issues seen on specific modems.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This prevents passing down the HOSTCC stuff set in u-boot.mk
which results in linking errors against openssl:
tools/mxsimage.o: In function `sb_aes_reinit':
mxsimage.c:(.text+0x202): undefined reference to `EVP_CIPHER_CTX_reset'
tools/mxsimage.o: In function `mxsimage_generate':
mxsimage.c:(.text+0x110d): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x114f): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x11c3): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x1323): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x134a): undefined reference to `EVP_CIPHER_CTX_reset'
tools/mxsimage.o: In function `mxsimage_verify_print_header':
mxsimage.c:(.text+0x23ce): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x242c): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x246b): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x24ef): undefined reference to `EVP_CIPHER_CTX_reset'
mxsimage.c:(.text+0x2e52): undefined reference to `EVP_MD_CTX_free'
collect2: error: ld returned 1 exit status
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
It is currently possible to enable connlabel-support in iptables.
However, in order for connlabel to work properly, the kernel module must
also be present. This patch adds support for building the
connlabel-module, and selects it by default when connlabel-support is
enabled.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
ls1012ardb/ls1012afrdm/ls1046ardb/ls1088ardb firmwares now use ubifs
rootfs. So u-boot env should be set accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Updated ppfe firmware to NXP LSDK1712 release. Used
ppfe firmware git tree on NXP github since it was
migrated here from qoriq-open-source github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
NXP LSDK1712 release used two rcw git trees. The
original rcw git tree was still source code but
dropping ls1012a/ls1088a/ls2088a boards in LSDK1712.
Instead another new rcw git tree was used to just
provided rcw binaries for these boards dropped. So
this patch is to update ls-rcw to LSDK1712 release
and add a new ls-rcw-bin package.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
fman-ucode had been migrated from qoriq-open-source
github to NXP github. So the Makefile should be fixed
accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Updated MC firmware to NXP LSDK1712 release. Used
MC firmware git tree on NXP github since it was
migrated here from qoriq-open-source github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
For hardware that supports multiple h/w output queues, add
a compatible scheduler (NET_SCH_MULTIQ).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Current code and also before commit da52dd0c83 was vulnerable to shell
injection using volume lables in the GPT partition table of block
devices. Given that partition names can be freely defined in GPT tables
we really shouldn't evaluate a string which is potentially crafted with
evil intentions. Hence rather use `export -n` to absorb the uevent's
variables into the environment.
Fixes commit da52dd0c83 (base-files: quote values when evaluating uevent)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[mschiffer@universe-factory.net: suggested export -n usage]
The kmod-lp package included both lp.ko and ppdev.ko, but ECP device
drivers may or may not require lp NOT to be loaded, needing only ppdev.
Additionally, There were no packages for any parport interface modules,
such as uss720 or parport_pc, provided here. It has not been otherwise
possible to use PC-style parport hardware for kmod-lp.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
The last_rx field was removed from net_device. Since the field wasn't
used by the generic subsystem, and the driver only writes to it, just
remove the usage.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
When sourcing /sys/class/block/*/uevent values have to be quoted as
they may contain spaces (e.g. in PARTNAME).
Fix this by pre-processing with sed before sourcing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.
[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* introduces the BDFs for the OpenMesh A42 in
/lib/firmware/ath10k/QCA4019/hw1.0/board-2.bin.
* adds new firmware firmware-6.bin_RM.4.4.1.c1-00037-QCARMSWP-1 for
QCA6174 hw3.0
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
With no warning, it just looks like the box has hung during boot.
We don't want users resetting it without having captured a crashdump.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Compiling the Intel microcode package results in a
microcode.bin and a microcode-64.bin. As we can
decide based on the subtarget which should be used,
we'll only split the required .bin file with
iucode-tool.
x64 will get the intel-microcode-64.bin
All other variants will get intel-microcode.bin
The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Use the Debian repository for sourcing the ucode files.
Current (20171205) includes support for fam17h CPUs already.
The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add tool to "compile" Intel microcode files. The tool will be
compiled for host (to split the microcode.dat) and for target
(to forcibly reload the microcode if required).
Instead of using the large microcode.bin/microcode-64.bin, the
splitted ucode files (separate for CPU families) will be
installed.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
When we provide the HOSTCFLAGS to the U-Boot build it will fail because
it can not find the u-boot provided header files any more.
Just overwrite and not append the package specific configuration on top
of the configuration provided by u-boot.mk.
uboot-fritz4040 is based on U-Boot 2012.07 and this problem is probably
similar to the problem seen with the lantiq and ar71xx u-boot build.
Fixes: df9781a420 ("u-boot,at91bootstrap: fix incorrect HOSTCPPFLAGS variable")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Once installed fou kernel module allows you to use FOU (Foo over UDP)
and GUE (Generic UDP encapsulation) tunnel protocols.
To get ip fou command working you also need to install ip-full.
Signed-off-by: Filip Moc <lede@moc6.cz>
Since I have no openssl-dev on my machine, I first
get this error:
```
tools/kwbimage.c:21:10: fatal error: openssl/bn.h: No such file or directory
#include <openssl/bn.h>
```
After removing the UBOOT_MAKE_FLAGS the next error is:
```
tools/kwbimage.c:40:6: error: conflicting types for ‘EVP_MD_CTX_cleanup’
void EVP_MD_CTX_cleanup(EVP_MD_CTX *ctx)
```
After removing the OpenSSL patches the next error is:
```
HOSTLD tools/dumpimage
/usr/bin/ld: cannot find -lssl
/usr/bin/ld: cannot find -lcrypto
collect2: error: ld returned 1 exit status
scripts/Makefile.host:108: recipe for target 'tools/dumpimage' failed
make[5]: *** [tools/dumpimage] Error 1
```
So, the final part is to add the build system's
HOST_LDFLAGS to the UBOOT_MAKE_FLAGS.
(which was done in the previous commit)
Then the image builds.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This would should up as `$$(HOSTCPPFLAGS)` in the host CFLAGS.
```
make --jobserver-fds=3,4 -j -C <openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/u-boot-A10-OLinuXino-Lime/u-boot-2017.07 CROSS_COMPILE=arm-openwrt-linux-muslgnueabi- DTC="<openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/linux-sunxi_cortexa8/linux-4.9.76/scripts/dtc/dtc" HOSTCC="gcc" HOSTCFLAGS='-O2 -I<openwrt>/staging_dir/host/include -I<openwrt>/staging_dir/host/usr/include -I<openwrt>/staging_dir/hostpkg/include -I<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/host/include $$(HOSTCPPFLAGS)' HOSTLDFLAGS="" BL31=<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/image/bl31.bin
```
And then it would complain with:
```
/bin/sh: 1: HOSTCPPFLAGS: not found
```
Also, HOSTCPPFLAGS does not exist.
The correct var is HOST_CPPFLAGS.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Activate the support for 64 bit on all 64 bit CPUs and not only x86_64.
ARM64 does not provide an xml file, so do not pack any.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3413961 mt7603: avoid reordering qos-null data packets
c60e6db mt76: toggle driver station powersave bit before notifying mac80211
246d548 mt76: stop tx queues from the driver callback instead of common code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The target it was meant for was updated to a version that this does not
compile with. It probably also hasn't been used in years
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't append an empty sendopts value as odhcp6c bails out
immediately on an empty -x option triggering an infinite start
loop of odhcp6c
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Commit a26045049b added support for sendopts as a string; since multiple
sendopts values can be specified it makes more sense to model it as a
list of strings.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The ATM subsystem is different from the generic ethernet NICs. The ATM
subsystem requires a callback when a packet has been sent. It means a
tx skb_buff need to be used after it has sent. While the generic NIC
can fill up the TX ring and free skb_buffs if it encounter a ring buffer slot
with an already sent skbuff.
The ATM drivers need call the pop() function after it has send a
single ATM package. The ATM subsystem controls via this ways the queuing.
The ppe engine use DMA channels for read and write. Every atm_vcc has it's
own TX DMA channel and each TX DMA channel has it's own ring buffer.
The old driver had multiple issues:
- Call the subsystem callback at the beginning of tx function (ppe_send).
Didn't allowed the ATM subsystem to control the enqueued package
amount.
- Filled up the TX ring until full and fail futher
- copy or decouple the skb from all other subsystem before giving it
over to TX ring
The new tx path uses interupts.
- call the subsystem callback _after_ it was sent by hardware
- no need to copy our decouple the skb any more
- gives back control to the atm subsystem over the enqueued packages
- use an interupt for every sent atm package
Using interupts shouldn't be a problem because of the slow uplink bandwidth of
ADSL.
The speed _through_ the DSL router was always as high as it should
be, only traffic generated on the router itself were affected.
After changing to new tx path, the speed of iperf's run on the
router itself reached the same speed. The master/trunk wasn't as much
affected because of TCP optimisations (reboot-5022-gb2ea46fe236a).
The following results are taken on the remote server, which receives
the stream over the internet and the DSL line.
The sync moves between every sync a litte bit, but is so far stable
Latency / Interleave Delay: Down: Fast (0.25 ms) / Up: Fast (0.50 ms)
Data Rate: Down: 13.287 Mb/s / Up: 1.151 Mb/s
reboot-5521-g9f8d28285d without patch
[ ID] Interval Transfer Bandwidth Retr
[ 5] 0.00-10.04 sec 947 KBytes 773 Kbits/sec 0 sender
[ 5] 0.00-10.04 sec 928 KBytes 757 Kbits/sec receiver
reboot-5521-g9f8d28285d with patch
[ 5] 0.00-10.06 sec 1.16 MBytes 970 Kbits/sec 0 sender
[ 5] 0.00-10.06 sec 1.15 MBytes 959 Kbits/sec receiver
v17.01.4-239-g55c23e44f4 without patch
[ ID] Interval Transfer Bandwidth Retr
[ 5] 0.00-10.04 sec 87.4 KBytes 71.3 Kbits/sec 0 sender
[ 5] 0.00-10.04 sec 59.6 KBytes 48.7 Kbits/sec receiver
v17.01.4-239-g55c23e44f4 with patch
[ ID] Interval Transfer Bandwidth Retr
[ 5] 0.00-10.05 sec 1.18 MBytes 983 Kbits/sec 1 sender
[ 5] 0.00-10.05 sec 1.15 MBytes 959 Kbits/sec receiver
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
- use release build instead of debug to reduce size
- bump to use latest commit in allwinner tree
Tested on Pine64/1G.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2b7fae4 mt76: fix returnvar.cocci warnings
939e3e0 mt76x2: dfs: avoid tasklet scheduling during mt76x2_dfs_init_params()
cf59170 mt76x2: dfs: add set_domain handler
5e4d60e mt76x2: dfs: take into account dfs region in mt76x2_dfs_init_params()
f76e25f mt76x2: fix WMM parameter configuration
34d612d mt76: retry rx polling as long as there is budget left
0f8327a mt76x2: fix TSF value in probe responses
ad3f8e9 mt76: add an intermediate struct for rx status information
58a41f1 mt76: get station pointer by wcid and pass it to mac80211
b0508d3 mt76: implement A-MPDU rx reordering in the driver code
cf3cfc4 mt76: split mt76_rx_complete
461cdf9 mt76: pass the per-vif wcid to the core for multicast rx
9b2c778 mt76: validate rx CCMP PN
302af90 mt76x2: init: disable all pending tasklets during device removal
9f685fe mt7603: init: disable tbtt tasklet during device removal
c6f8cac mt76: let mac80211 validate CCMP PN for fragmented frames
3968dae mt7603: fix 40 mhz channel bandwidth reporting
9c2e03d mt7603: fix rx LDPC reporting
f515dfc mt76: implement AP_LINK_PS
974142c mt76: implement processing of BlockAckReq frames
c5209db mt76: avoid re-queueing A-MPDU rx reorder work if no frames are pending
e67e7a5 mt76x2: do not set status->aggr for NULL data frames
8693864 mt76: check qos ack policy before reordering packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
f0836c7e Update manual pages
25db178b Bump up version number to 1.30.0, LT revision to 29:2:15
1b6713e6 Update AUTHORS
c1a496cf nghttpx: Fix bug that h1 backend idle timeout expires sooner
e098a211 mruby: Fix bug that response header is unexpectedly overwritten
0ba4bf51 Merge pull request #1120 from dylanplecki/issue-1119-mruby-header-overwrite
6deee203 Fix#1119: Stop overwrite of first header on mruby call to env.req.set_header(..)
6761a933 Merge pull request #1105 from nghttp2/nghttpx-upgrade-scheme
5cc3d159 nghttpx: Add upgrade-scheme parameter to backend option
652f57e7 Merge pull request #1104 from nghttp2/allow-ping-after-goaway
acd6b40e Allow PING frame to be sent after GOAWAY
0fbb46ed Merge pull request #1101 from nghttp2/remember-pushed-links
6ad629de Merge pull request #1102 from nghttp2/fix-missing-alpn-validation
74754982 nghttpx: Fix missing ALPN validation (--npn-list)
a31a2e3b nghttpx: Remember which resource is pushed
a776b0db Merge pull request #1092 from nghttp2/define-103
cfd926f0 src: Define 103 status code
72f52716 Bump up version number to 1.30.0-DEV
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Firewall rules don't work as intended without conntrack support. The recent
cleanup removed the kmod-nf-conntrack6 dependency from the iptables
modules; add it to the firewall package instead.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
