BOCCO is a communication robot provided by YUKAI Engineering Inc.
SoC: MT7620A
MEM: 256MB
Flash: 8MB
NAND: 512MB (non support)
Include Sound DAC and AMP.
No Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Mostly whitespace cleanups. Some unneeded code was removed.
MMC init was also moved to the probe function as in
6069bdd
The cleanup commits are over 100, making it hard to do them individually.
Tested on GnuBee PC1 with an SD card being used as swap.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
v2: Fixed compile issue with mt7620
Backport patch adding support for the vbus-supply devicetree property,
which allows to specific GPIOs (via fixed regulators) to enable
vbus/usb power.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: f079b6406348 ("staging: mt7621-eth: add gigabit switch driver (GSW)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function of_phy_connect() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is an amagalmation of two upstream commits dealing with whitespace
and dead code removal. I'm synching instead of having two separate commits
as they go out of order compared to previous commits here.
Tested on GnuBee PC1.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Mostly whitespace cleanups. Some unneeded code was removed.
MMC init was also moved to the probe function as in
6069bdd087
The cleanup commits are over 100, making it hard to do them individually.
Tested on GnuBee PC1 with an SD card being used as swap.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
These resources are extracted from devicetree, so they aren't
needed here.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code currently defines:
and then compiles code only if they are defined.
We might want to disable some of these via devicetree one
day, but for now just remove the #defines and the
conditions - all the code for different ports is
easy to identify.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the Interrupts for the PCI adapters are listed in
devicetree we shouldn't need to have them explicit in the code.
The simplest way to do this is to use of_irq_parse_and_map_pci()
and specify an interrupt-map which identifies the different
PCI hosts by bus/slot numbers.
This has the advantage that the hwirq number are mapped to virq
numbers for us, so the ugly hack can go.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the owner assignment form the platform driver as
platform_driver_register() already initializes the owner.
Found using coccinelle.
Signed-off-by: Christian Lütke-Stetzkamp <christian@lkamp.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Splitted out the dts file and create the new dts for the 256 MByte RAM and
the 512 MB RAM version.
Migrate both versions to the common board detection.
The install the 512 MByte Version on a board running the 256 MByte image,
a forceful sysupgrade with the -F flag is required.
Signed-off-by: Davide Ammirata <list@davidea.it>
The RavPower WD03 is a battery powered SD card reader and a USB port.
Specifications:
SOC: MediaTek MT7620N
BATTERY: 6000mah
WLAN: 802.11bgn
LAN: 1x 10/100 Mbps Ethernet
USB: 1x USB 2.0 (Type-A)
RAM: PM Tech PMD708416CTR-5CN 32 MB
FLASH: Holtek HT66F40 - 8 MB Flash
LED: Power button and 4 leds to indicate power level of the
battery (could not get control of that)
INPUT: Power, reset button
OTHER: USB SD-Card reader with card detect on GPIO#42
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Installation:
- Download the sysupgrade image
- Place it in the root of a clean TFTP server running on your computer.
- Rename the image to "kernel" — be sure there is no file extension.
- Plug the WD03 into your computer via ethernet.
- Set your computer to use 10.10.10.254 as its IP address.
- With your WD03 shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The WD03 (10.10.10.128) will look for your computer at 10.10.10.254
and install the kernel file. Once it has finished installation of the
kernel file, it will search for a (nonexistent) rootfs file — when it
begins searching for this file, shut down the WD03 by holding the
power button normally.
- Start up your WD03 normally.
Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
There is no pinmux group "jtag" for mt7628 and the pinmux driver fails
to load due to the use of the not existing group.
Fixes: FS#1515
Signed-off-by: Mathias Kresin <dev@kresin.me>
The old DTB method (OWRTDTB) is not recognized by the boot process
anymore with 4.9/4.14.
This patch reuses KERNEL_DTB to get a valid DTB applied to the kernel
image.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
Merge the two existing functions and use a parameter for the type
header field.
It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The stats update needs to protect against being interrupted by a tasklet
The u64 stats seqlock needs to be initialized
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The pins are used as (LED) GPIOs and can't be used at the same time as
hardware controlled ephy (LED) pins.
Fixes: FS#1500
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the new USB phy driver, it checks the compatible string before
attempting to iomap its mem resource and do the extra PHY init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With kernel 4.14 the OpenWrt specific module name collides with the
upstream added module for Mediatek ARM Socs.
During addition of preliminary support for kernel 4.14, the config
symbol used by the out of tree driver was already renamed but the ramips
kernel package wasn't updated.
Fix the build error by updating the config and kernel module name for
the kernel package.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Zorlik ZL5900V2 is an unbranded clone of HAME MPR-A1/2. It is
marketed as "3G Wi-Fi Router". Only the PCB has the model name
"ZL5900V2" printed on it.
Specifications:
- Ralink RT5350F (360 MHz)
- 32 MB RAM
- 8 MB Flash
- 802.11bgn 1T1R
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (Type-A)
- 5200 mAh battery
The ramdisk image (not the squashfs sysupgrade image) can be flashed
through the web interface (named "GoAhead") of the factory firmware.
However, as the factory firmware does not cleanly unmount the rootfs
before flashing, the device may hang instead of rebooting after
successful write. Power cycling the device gets you in OpenWrt where
the squashfs image may be flashed through normal sysupgrade procedure.
Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
YouHua tech WR1200JS is an AC1200 router with 5 1Gb ports (4 Lan, 1 Wan)
and 1 USB 2.0 port.
Devices is base on MediaTek MT7621AT + MT7603E + MT7612E.
Specification:
- MT7612AT (880 MHz)
- 128 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 5x 10/100/1000 Mbps Ethernet
- 2T2R 2.4 GHz (MT7603E)
- 2T2R 5 GHz (MT7612E)
- 1x USB 2.0
- 10x LED (Power 2G 5G WPS Internet LAN4-1 USB)
- 3x button (reset wifi wps)
- DC jack for main power input (12V)
Installation:
1.) Press reset key 5 sec and restore the factory default
2.) Login webUI and change username to root and set a
new password
3.) Visit http://192.168.2.254/adm/telnetd.shtml and
turn on the telnet service
4.) Copy openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin
to a usb pan
5.) Plug the usb pan to the router, telnet to the router
and login by root
6.) cd /media/sda1 and check the initramfs file is there
7.) exec command:
mtd_write write openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin Kernel
8.) reboot and visit 192.168.1.1
Signed-off-by: Zheng Qian <sotux82@gmail.com>
The previous fw version require the replacement of the stock bootloader
with u-boot. This prevent an easy stock restore of the original fw.
Now a proper fw util has been developed to manage the stock jboot
bootloader. Therefore make sense have a fw image for the stock
bootloader.
The old fw configuration (u-boot) is not compatible with the new one
and will not be supported anymore.
So at the end 2 image can be generated:
1) factory image with jboot bootloader
openwrt-ramips-rt305x-dwr-512-b-squashfs-factory.bin
2) sysupgrade image with jboot bootloader
openwrt-ramips-rt305x-dwr-512-b-squashfs-sysupgrade.bin
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
The Ralink USB PHY driver merged into mainline has a slightly different
device tree binding than the patch that was used with linux 4.9.
The new driver requires a `ralink,sysctl` node pointing to the `syscon`
node.
This patch also sets `#phy-cells` to 0, as recommended by the mainline
documentation [1].
[1] Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
Supports IPv4 flow offloading on MT7621 for Routing, SNAT and DNAT
Supported are regular ethernet->ethernet connections, including one
802.1q VLAN and/or PPPoE encapsulation
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
of_dma_configure() sets a default ->dma_mask of
DMA_BIT_MASK(32), claiming devices can DMA from
the full 32bit address space.
The mtk-mmc driver does not support access to
highmem pages, so it is really limited to the
bottom 512M (actually 448M due to 64M of IO space).
Setting ->dma_mask to NULL causes mmc_setup_queue()
to fall-back to using BLK_BOUNCE_HIGH to tell the
block layer to use a bounce-buffer for any highmem
pages requiring IO.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Our .dts files only have one device defined and this is unlikely to
change, so statically initialize host->id to 0.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The DWR-921-C3 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
The status led has been assigned to the dwr-921-c1:green:sigstrength (lte
signal strength) led. At the end of the boot it is switched off and is
available for lte operation. Work correctly also during sysupgrade
operation.
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
drivers/mmc/host/mtk-mmc/dbg.c:51:13: warning: 'cmd_buf' defined but not used [-Wunused-variable]
static char cmd_buf[256];
^~~~~~~
In addition, msdc_reg[] is completely unused, even in debug
mode.
Signed-off-by: André Draszik <git@andred.net>
msdc_6575_host[] is unused, just remove it. Also, it
was the source of memory corruption up until the
previous fix to this driver.
Signed-off-by: André Draszik <git@andred.net>
pdev->id is -1 when only one device exists, and is used:
* as an index into drv_mode[] to determine whether to use
PIO or DMA mode (via host->id)
* as an index into msdc_6575_host[], to store the
mmc_priv() data.
Obviously, -1 is not a valid index in either case, causing
us to read invalid memory, and memory corruption,
respectively.
The invalid memory read is causing non-deterministic
behaviour, in particular in the v4.4 kernel it still
picked DMA mode, but in the v4.9 it now always picks
PIO mode.
Also, PIO mode doesn't work, causing the following:
/ # echo 3 > /proc/sys/vm/drop_caches
[ 3845.249237] sh (128): drop_caches: 3
/ # /root/usr/lib/libc.so
[ 3846.096070] do_page_fault(): sending SIGSEGV to libc.so for invalid read access from 7f9cb5a0
[ 3846.104758] epc = 779b0ea4 in libc.so[7792f000+c3000]
[ 3846.109907] ra = 779a8004 in libc.so[7792f000+c3000]
Segmentation fault
/ # /root/usr/lib/libc.so
musl libc (mipsel-sf)
Version 1.1.16-git-40-g54807d47
Dynamic Program Loader
Usage: /root/usr/lib/libc.so [options] [--] pathname [args]
(i.e. initial page-in of any binary causes a segfault,
subsequent access works.)
While this change doesn't fix PIO mode, it at least makes
us deterministically use DMA (which works), and it also
stops us from corrupting memory.
Signed-off-by: André Draszik <git@andred.net>
