On bcm53xx and brcm47xx, commands are passed to default_do_upgrade that
expect the image to be passed on stdin, rather than as an argument.
Fixes: 30f61a34b4 ("base-files: always use staged sysupgrade")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fix condir option processing allowing to use the format
"<directory>[,<file-extension>......]," as documented on the dnsmasq man
page which previously resulted into bogus dir being created.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
On some targets this module depends on kmod-of-mdio.
This is similar to the fixes done in:
dc629d9cf5 ("kernel: fix kmod-switch-rtl8366-smi dependency")
56bd23cf52 ("kernel: let kmod-rtl8366-smi conditionally depend on kmod-of-mdio")
Fixes: 32f32398af ("kernel/modules: add kmod-mdio-gpio module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some ath10k firmware versions allow to access the chip internal a
temperature sensor and allow to reduce the amount of the time when the card
is allowed to send. The latter is required on devices which tend to
overheat.
An userspace service has to read
/sys/class/ieee80211/phy*/device/hwmon/hwmon*/temp1_input regularly and
then decide how much the device has to be throttled. This can be done by
writing to /sys/class/ieee80211/phy*/device/cooling_device/cur_state. By
default it is not throttled (0) but it can be throttled up to 100(%).
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Without this change, ifx_mei_atm_showtime_check() will always return
"showtime" after one call of MEI_InternalXtmSwhowtimeEntrySignal()
was done, even if MEI_InternalXtmSwhowtimeExitSignal() was called
in the meantime.
The ifx_mei_atm_showtime_check() function is used by the ltq-atm and
ltq-ptm driver.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Some of the ubi-tools in the upstream mtd-utils have been
broken by a bad patch upstream. It causes major breakage
during sysupgrade when the kernel, rootfs, ... volumes
are deleted in the wrong order.
This patch therefore reverts the faulty upstream commit which
fixes the bug.
linux-mtd mailing-list thread:
<http://lists.infradead.org/pipermail/linux-mtd/2018-June/081562.html>
Cc: John Crispin <john@phrozen.org>
Reported-by: L. Wayne Leach <LLeachii@aol.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This reverts a change made in Sep 2017 [1] which introduced
MSG_DONTROUTE flag to prevent udhcpc from reaching out to servers on a
different subnet. That change violates RFC2131 by forcing fully
configured clients, who got their configurations through an offer
relayed by a DHCP relay, from renewing through a unicast request
directly to the DHCP server, resulting in the client resorting to
boradcasting lease extension requests instead of unicasting them,
further breaking RFC2131.
The problem with MSG_DONTROUTE appears when talking to a properly
configured DHCP server that rejects non-compliant requests. Such server
will reject lease extension attempts sent via broadcast rather than
unicast, as is the case with Finnish ISPs Telia and DNA as well as
Estonian ISP Starman. Once the lease expires without renewal, udhcpc
enters init mode, taking down the interfaces with it, and thus causing
interruption on every lease expiry. On some ISPs (such as the ones
mentioned above) that can be once every 10-20 minutes. The interruptions
appear in the logs as such:
----
udhcpc: sending renew to x.x.x.x
udhcpc: send: Network unreachable
udhcpc: sending renew to 0.0.0.0
udhcpc: sending renew to 0.0.0.0
...
udhcpc: lease lost, entering init state
Interface 'wan' has lost the connection
Interface 'wan' is now down
Network alias 'eth0' link is down
udhcpc: sending select for y.y.y.y
udhcpc: lease of y.y.y.y obtained, lease time 1200
Network alias 'eth0' link is up
Interface 'wan' is now up
----
During lease extension, a fully configured client should be able to
reach out to the server from which it recieved the lease for extension,
regardless in which network it is; that's up to the gateway to find. [2]
This patch ensures that.
[1]
http://lists.busybox.net/pipermail/busybox-cvs/2017-September/037402.html
[2]
https://www.netmanias.com/en/post/techdocs/6000/dhcp-network-protocol/
understanding-dhcp-relay-agents
Signed-off-by: Adi Shammout <adi.shammout@outlook.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If log_file is specified, make sure its directory exists.
Signed-off-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
SourceForge is deprecated according to upstream, so switch to main site
for downloads.
Tested on Turris Omnia (mvebu).
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Problem - rapsberry pi 3 b/b+ does not boot with bcm2710 images!
How Raspberry Pi boots Actualy?
When Raspberry is switched on GPU is activated.
1. GPU execute First stage bootloader from ROM.
First stage bootloader mount the FAT boot partition on the SD card
and execute second stage bootloader (bootcode.bin).
2. Second stage bootloader (bootcode.bin) activate SDRAM.
Load the GPU firmware (start.elf).
3. GPU firmware (start.elf)
a) display Rainbow splash.
b) read firmware configuration file config.txt and
split the RAM using fixup.dat.
c) loads a cmdline.txt
d) enables the CPU.
e) loads the kernel image configurable via config.txt
In your target/linux/brcm2708/image/config.txt
493 ## kernel (string)
494 ## Alternative name to use when loading kernel.
495 ##
496 #kernel=""
it is not configured!
But in your target/linux/brcm2708/image/Makefile
75 KERNEL_IMG := kernel8.img
76 DEVICE_TITLE := Raspberry Pi 3B/3B+
you have kernel8.img
GPU Firmware search order by default for a PI 3 is:
kernel8.img if found boot in 64 bit mode
kernel8-32.img if found boot in 32 bit mode
kernel7.img if found boot in 32 bit mode
kernel.img if found boot in 32 bit mode
But a PI 2 will start the search from kernel7.img and
a PI 1 only looks for kernel.img.
Оbviously the kernel has been found.
But something goes wrong and the device is restarted.
In your package/kernel/brcm2708-gpu-fw/Makefile
11 PKG_NAME:=brcm2708-gpu-fw
12 PKG_VERSION:=2017-08-08
13 PKG_RELEASE:=e7ba7ab135f5a68b2c00a919ea9ac8d5528a5d5b
boot loader is 10 monts old.
In conclusion, the best way to solve the problem is
to update the boot loader!
Fixup_cd.dat and start_cd.elf files are not necessary.
These are used when GPU memory is set to 16 MB, which disables
some GPU features.
I did not remove them just in case!
cheers
Signed-off-by: Christo Nedev <christo.nedev@gmail.com>
5699354 extensions: fix build failure on fc28
e6359ee build: update ebtables.h from kernel and drop local unused copy
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
There are several long-standing issues present in the UCI shell API as
documented in https://wiki.openwrt.org/doc/devel/config-scripting. They
relate both to high-level, user-defined callback functions used to
process UCI config files, and also to low-level functions used within
scripts generally.
The related problems have been encountered now and in the past, e.g.
https://forum.openwrt.org/viewtopic.php?id=54295, and include:
a) UCI parsing option() function and user-defined option_cb() callbacks
being erroneously called during processing of "list" config file entries;
b) normal usage of the low-level config_set() unexpectedy calling any
defined option_cb() if present; and
c) handling of the list_cb() not respecting the NO_CALLBACK variable.
Root causes include a function stack "inversion", where the low-level
config_set() function incorrectly calls the high-level option() function,
intended only for processing the "option" keyword of UCI config files.
This change addresses the inversion and other issues, making the option
handling code more consistent and smaller, and simplifying developers'
usage of UCI callbacks.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
20c0766 mt7603: adjust rx hang watchdog for MT7628
664e321 mt7603: add extra PSE hang check signature for MT7628
f24b56f update MT7628 firmware to the latest version
d87e4b0 mt7603: clear PSE reset bit if PSE reset fails
0ef26ef mt76: only stop tx queues on offchannel, not during the entire scan
f399da3 mt76: prevent tx scheduling during channel change
21c1e1e mt76: move ieee80211_hw allocation to common core
730c292 mt76: wait for pending tx to complete before switching channel
fcbb49e mt76x2: use udelay instead of usleep_range in mt76x2_mac_stop
792dbe0 mt7603: do not hold dev->mutex while flushing dev->mac_work
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501.
Setting the uci parameter encaplimit to ignore; allows to disable the insertion
of the destination option header in the map-e packets.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit uci parameter accordingly.
If no encaplimit value is specified the default value is 4 as before.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501 for dynamic created ds-lite/map
interfaces.
Setting the uci parameter encaplimit_dslite/map to ignore; allows to disable the insertion
of the destination option header for the dynamic created ds-lite/map interface.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit_dslite/map uci parameter accordingly.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501.
Setting the uci parameter encaplimit to ignore; allows to disable the insertion
of the destination option header in the ds-lite packets.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit uci parameter accordingly.
If no encaplimit value is specified the default value is 4 as before.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.
Functional issues:
* PCIe won't come up (hence no USB3 on Shuttle KD20)
* I2C bus of Akitio myCloud device is likely not to work (missing
debounce support in new pinctrl driver)
Code-style issues:
* plla/pllb needs further cleanup -- currently their users or writing
into the syscon regmap after acquireling the clk instead of using
defined clk_*_*() functions to setup multipliers and dividors.
* PCIe phy needs its own little driver.
* SATA driver is a monster and should be split into an mfd having
a raidctrl regmap, sata controller, sata ports and sata phy.
Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Do not set device runtime property on interfaces in the hotplug handler
and in fixup_interfaces(). This property conflicts with device option
in several proto handlers (mainly QMI and other WWAN/3G protos) and does
not seem to be used anywhere.
Signed-off-by: Ivan Shapovalov <intelfx@intelfx.name>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
3.4 is mainly a bug fix/maintenance release.
3KB increase in ipk lib size on mips.
Compile tested for: ar71xx, ramips
Run tested on: ar71xx Archer C7 v2, ramips mir3g
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The mtd tool is built with different configurations depending on the
target. For example, brcm47xx adds the fixtrx subcommand, without which
an image fails when booting the second time.
Mark the mtd package as nonshared to really fix FS#484.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
This version bump was made upstream mostly for OpenWRT, and should fix
an issue with a null dst when on the flow offloading path.
While we're at it, Kevin and I are the only people actually taking care
of this package, so trim the maintainer list a bit.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Clean up conflicts/provides/depends hell and add PROVIDES for
eapol-test variants while at it.
Update mesh-DFS patchset from Peter Oh to v5 (with local fixes) which
allows to drop two revert-patches for upstream commits which previously
were necessary to un-break mesh-DFS support.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Implicetely selecting the required options via Kconfig snippet from
hostapd worked fine in local builds when using menuconfig but confused
the buildbots which (in phase1) may build wpad-mini and hence already
come with CONFIG_WPA_WOLFSSL being defined as unset which then won't
trigger changing the defaults of wolfssl.
Work around by explicitely reflecting wpa_supplicant's needs in
wolfssl's default settings to make buildbots happy.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While building, curl complains that the path specified is missing.
Also, without ca-bundle, something like 'curl https://www.google.com'
does not work due to a certificate verify error.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
It simplifies the Makefile a bit. In addition, using ca-bundle
saves some space as well.
It also fixes an issue with at least transmission, which has a dependency
on ca-bundle, but currently libcurl with OpenSSL or GnuTLS cause it not
to work.
This has been tested on mt7621 with OpenSSL and GnuTLS just by running
'curl https://www.google.com' and seeing if there's a verify error.
The rest are already using ca-bundle and therefore work fine.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Import a revert-commit from Stanislaw Gruszka which significantly
improves WiFi performance on rt2x00 based hardware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently when installing the firmware, a bunch of files and directories
that the ath10k driver does not look for are created.
The package now installs firmware for both hw 2.1 and 3.0 devices.
2.1 is abandonware but may be useful to keep.
3.0 firmware was tested on a Killer 1535 to be relatively stable with
802.11w disabled. 802.11w causes multiple firmware crashes but that's true
of other ath10k firmwares as well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This change will trigger rebuild on buildbots in case of changed config
symbols, like in the case of hostapd selecting some wolfssl symbols
lately.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of selecting the SSL provider at compile time, build package
variants for each option so users can select the binary package without
having to build it themselves.
Most likely not all variants have actually ever been user by anyone.
We should reduce the selection to the reasonable and most used
combinations at some point in future. For now, build them all.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
