This replaces old bcm53xx patch for scanning whole flash and makes
bcm47xxpart compatible with NAND.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47800
Starting with r47755 the pppoe wan interface section isn't any longer added to
the network config on firstboot, using the default configuration. Since the
commit message does not mention such a change, I assume that this wasn't
intentionally.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47793
This version and version 3.6.8 are fixing the following security problems:
* CVE-2015-7744
* CVE-2015-6925
The activation of SSLv3 support is needed for curl.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47791
- update mtd-utils to 1.5.2 (git a494d30ab1ae40cb7665680cadf5af3ca3830a73)
- remove patches that went upstream
- fixes build from scratch as of broken patches
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[use the final version of 1.5.2 instead, fix header of jffs2_lzma_(de,)compress()]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47790
This should ensure that lldpd is among the first processes to stop,
so that it has time to send the shutdown LLDPU to the other side,
before the network goes down.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47786
Now that we have redistributable vdsl/adsl firmware blobs in /lib/firmware,
we can drop the dsl_fw partition and extend the firmware partition.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47783
Support next to the non-HT/HT channel widths like HT20 or NOHT also VHT80
channels during the mesh join
iw dev mesh0 mesh join "meshnet" freq 5180 80MHz
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47782
Fix the id of NL80211_ATTR_WIPHY_ANTENNA_GAIN for antenna_gain command when
using compat-wireless 2015-10-26.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47778
r47288 updated to Busybox 1.24.1 but did not update the configuration.
The configuration is updated by running
cd config
../convert_menuconfig.pl .../build_dir/target-*/busybox-1.24.1
cd ..
./convert_defaults.pl < .../build_dir/target-*/busybox-1.24.1/.config > \
Config-defaults.in
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 47775
Use the 'typical' compile configuration instead of 'full', which most
notably excludes the soap support.
/sbin/vdsl_cpe_control shrinks down to ~50%, from 178kb(!) to 90kb.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47769
Now that IPV6 isn't build as a module anymore, we don't need to decouple
bridge from ipv6 anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47751
This adds support for specifying the dsl modem, atm bridge configs and setting
the pppoe protocol for wan.
These additions are required to port the Lantiq target to board.d.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47750
