We enabled lua interpreter by default as it doesn't make any problem in the uhttpd config file and we modify the index page to use it.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Add rut5xx GPIO PIN selection to om-package startup script.
Testet on a RUT500 device, the timeout value of the hardware watchdog
is about 280 sec.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
[split into two commits, bump PKG_RELEASE]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
93abe6f config: fix invalid hoplimit in RA message
2ae08d1 config: fix invalid retranstime in RA message
0005cb4 config: fix invalid reachabletime in RA message
5683dd2 config: limit ra_mtu to 65535
f8d40a5 router: fix interface mtu read error
f8f4b87 config: limit ra_retranstime to 60000
a2d8bf6 dhcpv4: display two hex digits per octet in syslog
a9e9bc4 config: make RA retransTime configurable via uci
2cb6b48 config: make RA reachableTime configurable via uci
e4504db config: make RA curHopLimit configurable via uci
9dd5316 config: make RA mtu configurable via UCI
29cb2ff config: fix dhcpv4 server being started
0ef74ec ndp.c: add switch/case fallthrough comments
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
uci_set_leds_ataport() allows to set a led to show activity
on a specific (s)ata port, which is needed for devices that have
a Sata led for each sata port.
The led trigger is from the 834-ledtrig-libata.patch LEDE kernel patch.
uci_set_leds_usbhost() allows to set a led to show total usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
create a function with code common to all led functions,
create another function with code common to functions setting
a simple led trigger, restore alphabetical order in function names.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Gracefully handle cases where the to-be-created wireless interface already
exists on the system which might commonly happen with non-multi-SSID capable
wireless drivers.
This fixes commit 8301e61365 which caused
previously ignored "Too many open files in system (-23)" errors to fail the
wireless setup procedure.
With the updated approach we'll still try recreating the vif after one
second if the first attempt to do so failed with ENFILE but we will now
consider the operation successfull if a second attempt still yields ENFILE
with the requested ifname already existing on the system.
Fixes FS#664, FS#704.
Suggested-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add support for SolidRun ClearFog Base board.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
One of the latest mac80211 updates added sanity checks, requiring the
beacon intervals of all VIFs of the same radio to match. This often broke
AP+11s setups, as these modes use different default intervals, at least in
some configurations (observed on ath9k).
Instead of relying on driver or hostapd defaults, change the scripts to
always explicitly set the beacon interval, defaulting to 100. This also
applies the beacon interval to 11s interfaces, which had been forgotten
before. VIF-specific beacon_int setting is removed from hostapd.sh.
Fixes FS#619.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
None of the variables in this "local" declaration are actually set in
wpa_supplicant_add_network().
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some external toolchains may be configured to enable OpenMP. Provide a
package for these libraries which can be used by other packages.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the necessary changes to CMakeLists.txt to search zlib.h. Fixes
build issues with external toolchains that don't have STAGING_DIR in the
default search path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Toolchain built for ARCv1 (read for ARC700 cores) by default has
disabled atomic ops (-mno-atomic). When we build Linux kernel for ARC770
which has LL/SC instructions and thus may handle normally atomic ops we
explicitly add "-matomic" in CFLAGS. But since user-space perf utility has
no way to extract CPU config options from Kconfig/defconfig it uses
compiler default settings.
In case of ARCv2 (read ARC HS38) atomics are enabled by default and so
perf builds perfectly fine thus reenabling perf for ARC HS38 (actually
for non-ARC700 targets).
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
This patch adds the interface-name option for each dhcp config
in /etc/config/dhcp.
With the interface_name option users can define a DNS name for each dhcp section
that will be resolved by dnsmasq with the underlaying interface address.
For example:
config dhcp 'lan'
option interface 'lan'
...
list interface_name 'home.lan'
...
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If there's a TFTP root directory configured, create it with mkdir -p
(which does not throw an error if the folder exists already)
before starting dnsmasq. This is useful for TFTP roots in /tmp, for example.
Originally submitted by nfw user aka Nathaniel Wesley Filardo
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Setting legacy_rates to 0 disables 802.11b data rates.
Setting legacy_rates to 1 enables 802.11b data rates. (Default)
The basic_rate option and supported_rates option are filtered based on this.
The rationale for the change, stronger now than in 2014, can be found in:
https://mentor.ieee.org/802.11/dcn/14/11-14-0099-00-000m-renewing-2-4ghz-band.pptx
The balance of equities between compatibility with b clients and the
detriment to the 2.4 GHz ecosystem as a whole strongly favors disabling b
rates by default.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, defaults change]
When sta is configured, hostapd receives 'stop' and 'update' command from
wpa_supplicant. In the update command, hostapd gets sta parameters with
which it configures ap.
Problem is, with the default wireless configuration:
mode:11g freq:2.4GHz channel:1
If sta is connected to 5GHz network, then ap does not work. Ideally with
340-reload_freq_change.patch hostapd should reload the frequency changes
and start ap in 5GHz, but ap becomes invisible in the network.
This issue can be reproduced with following /etc/config/wireless:
config wifi-device radio0
option type mac80211
option channel 1
option hwmode 11g
option path 'virtual/uccp420/uccwlan'
option htmode 'none'
config wifi-iface 'ap'
option device 'radio0'
option encryption 'none'
option mode 'ap'
option network 'ap'
option ssid 'MyTestNet'
option encryption none
config wifi-iface 'sta'
option device radio0
option network sta
option mode sta
option ssid TestNet-5G
option encryption psk2
option key 12345
This change updates current_mode structure based on configured hw_mode
received from wpa_supplicant. Also prepare rates table after frequency
selection.
Signed-off-by: Abhilash Tuse <Abhilash.Tuse@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, patch refresh]
Commit 2036ae4 (base-files: support hostname and ntp servers through board.d)
was supposed to implement these procedures but lacked the required changes
to uci-defaults.sh.
Add the missing procedures now to fix config generation on targets relying
on hostname or NTP server presetting.
Fixes FS#754.
Reported-by: Cristian Morales Vega <cristian@samknows.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When busybox customisation is enabled, we should depend on config
symbols CONFIG_BUSYBOX_CONFIG_xxx to form alternatives specs
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
A number of small tweaks & improvements on the way to a final release.
Most notable:
Improve DHCPv4 address-in-use check.
Remove the recently introduced RFC-6842 (Client-ids in DHCP replies)
support as it turns out some clients are getting upset.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Changes since last version
546bc72 pkg: alternatives support
7a96972 libbb: xreadlink: fix memory leak on failure case
3f13edd pkg_run_script: use pkg->dest in half installed case
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
arc-2016.09 is the most recent toolchain for ARC cores and
it is based on top of upstream Binutils 2.27 and GCC 6.2.1.
With updated major version of GCC we copied all GCC 6.x patches
for ARC as well as Bintils 2.27 patches.
Note that toochain sports ARCv4 ABI and so must be used
with 4.8+ Linux kernels. Even though it will build v4.4 kernel
perfectly fine on attempt to run user-space apps they won't
work with older kernel. That said previuosly sent RFC patches with
Linux kernel update are required:
[1] https://patchwork.ozlabs.org/patch/726686/
[2] https://patchwork.ozlabs.org/patch/726687/
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Even it's unknown if it's booting with thumb, because the lack of hardware.
Enable it for now, so the build succeed, because without thumb it can not fit
into spl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
9268ca6 ndp: don't trigger IPv6 ping when neighbor entry is invalid
2b3355f ndp: fix adding proxy neighbor entries
7dff5b4 ndp: fix wrong interface name in syslog message
a54afb5 dhcpv6-ia: Fix segfault when writing DHCPv4 leases in state file
c0e9dbf ubus: don't segfault when there're no leases
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Configuring dhcp_option as an option does not allow the usage of white
spaces in the option value; fix this by supporting dhcp_option as a list
config while still supporting the option config to maintain backwards
compatibility
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
When invoking "nslookup_lede" with a domain argument and without explicit
query type, issue both A and AAAA queries and display the resulting IP
addresses in a numbered list style, similar to how the old BusyBox nslookup
used to output the records.
This is required for compatibility with certain scripts.
Ref: https://forum.lede-project.org/t/nslookup-ipv6-in-lede-17-01-1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The ":*" optstring syntax was only recently introduced with BusyBox v1.26,
older versions need a corresponding hint in the "opt_complementary" variable
to denote flag values that should be stored as llist entries.
Add the required opt_complementary entry to fix random SIGBUS, SIGILL or
SIGSEGV related crashes on BusyBox 1.25.x when attempting to use the "-q"
flag of the "nslookup_lede" applet.
Ref: https://forum.lede-project.org/t/nslookup-ipv6-in-lede-17-01-1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Install procd interface triggers only for interfaces which are enabled
so dropbear instances running on (an) enabled interface(s) are not
restarted due to an interface trigger of an interface which is disabled.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Merged upstream in https://patchwork.kernel.org/patch/9572541/, this
patch fixes the OTP offset used by the AR934x and AR955X to properly
enable reading from the OTP.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
