The Cisco ON100 device is a Kirkwood based router:
SoC: Marvell 88F6282 1600Mhz
SDRAM memory: 512MB DDR3 1333Mhz
Gigabit ethernet: 2x Marvell 88E1310 (over RGMII)
Flash memory: 512MB
2 bi-colour status LEDs (green/red)
1 Reset button
1 USB 2.0 port (on back)
1 SDIO slot (on back)
This commit adds a target profile of "Cisco Systems ON100" under the target
system "Marvell Kirkwood".
Flashing can be performed over tftp, once "dhcp" has been issued:
tftpboot ${loadaddr} lede-kirkwood-on100-squashfs-factory.bin
nand erase 0x0c0000 ${filesize}
nand write ${loadaddr} 0x0c0000 ${filesize}
Once flashed, set environment variables to boot:
setenv bootcmd nand read \${loadaddr} 0x0c0000 0x540000\; setenv bootargs
\; bootm
saveenv
Signed-off-by: Makoto Takeuchi <mak0@lxsys.co.uk>
these two devices have a Sata led for each sata port.
These leds must be controlled separately by a special
sata led trigger already used in oxnas target.
Both these devices have a single USB led, and to keep
consistent behaviour with the Sata leds that show
sata activity, this led uses usb-host trigger
to show usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
the mtd_get_mac_ascii function called within this script requires the inclusion of /lib/functions/system.sh
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This patch add ZyXEL NSA325 2-Bay Media Server
The ZyXEL NSA325 device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1600Mhz
- SDRAM memory: 512MB DDR2 400Mhz
- Gigabit ethernet: Marvell Alaska
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II ports (internal)
- 2 USB 2.0 ports (back)
- 1 USB 3.0 port (front)
- Fan (fixed speed)
- hardware watchdog in a mcu
Basically a bigger, more powerful version of NSA310,
installation is the same as they share the same flash layout.
A notable difference is that there is a hardware watchdog
in a mcu on the board, which is disabled by default in the LEDE u-boot.
The watchdog is also disabled with a GPIO activation through
raw register change when kwbooting or it would reset the board before
the new uboot was transferred.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
switch nsa310b mac address reading to mtd_get_mac_ascii helper as
it seems the fw_env.config file is created way later than when
network is set up, when I tested I still had that file included
in the image through /files folder.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
The ZyXEL NSA310 device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: Realtek (over pcie)
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II port (1 internal and 1 external)
- 2 USB 2.0 ports (1 front and 1 back)
- Smart fan
The stock u-boot cannot read ubi so it should be replaced with the
LEDE/OpenWRT's u-boot or with a u-boot from here
https://github.com/mibodhi/u-boot-kirkwood
This device's boot ROM supports "kwboot" tool
(in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared)
that sends an uboot image to the board over serial connection, it is very easy to unbrick.
The stock bootloader can use usb and read from FAT filesystems,
so the installation process is simple, place the uboot file on a USB flashdrive
formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL
to the board and write the following commands in the bootloader console:
usb reset
fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin
nand write 0x1000000 0x00000 0x100000
reset
Now you are rebooting in the new u-boot, write this in its console to install the firmware:
usb reset
fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin
nand erase.part ubi
nand write 0x2000000 ubi 0x600000
If your firmware file is bigger than 6 MiBs you should write its size in hex
instead of 0x600000 above, or remove that number entirely (it will take a while in this case).
If you are using another uboot that can read ubi, set mtdparts like this
mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi)
And set your bootcmd to be like this
bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000
Then you can install the firmware as described above.
After you installed (or configured) the u-boot for booting the firmware,
write the device's mac address in the ethaddr u-boot env.
The MAC address is usually on a sticker under the device (one of the two codes is the serial),
it should begin with "107BEF" as it is assigned to ZyXEL.
write in the u-boot console (use your MAC address instead of the example)
setenv ethaddr 10:7B:EF:00:00:00
saveenv
to save the mac address in the u-boot.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Remove dt: it is implicitly enabled based on the kernel config
Remove tar.gz and jffs2_nand: Legacy build code has been removed,
NAND devices are only supported with UBI now.
Remove ubifs: deprecated, use squashfs images instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove redundant code: merge boards/cases that share
the same network configuration.
Also fix the alphabetical ordering of the cases.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Using pad-to instead of passing the optional padding to append-kernel
or append-rootfs. It could be that the value of a variable is passed.
In case the variable is empty no error is thrown.
Furthermore the purpose of the extra parameter is hard to get without
reading the code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto
Signed-off-by: Mathias Kresin <dev@kresin.me>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The query for ARMADA_THERMAL is stalling the kconfig process and as long as we
do not package it, simply disable the symbol.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Dropped patches because they applied upstream:
- 120-iomega_ix2_200.patch
- 150-pogoplug_e02.patch
Tested on dockstar and goflexnet.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 49019
Previous the uboot was overwriting the device-tree's mtd layout to use
the last 3 mb.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49015
The kernel will automatic attach mtd partitions named 'ubi' to ubi0.
Renaming the "root" partition into "ubi" will safe arguments
from the kernel cmdline.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49014
the kernel tries to use "ubi" or "data" labeled partition to find it's root filesystem.
dockstar don't need anymore mtdparts= nor root= bootarguments
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49011
The new image requires `bootz` because of devicetree appending.
To flash a new image boot initramfs:
tftpboot 0x800000 openwrt-kirkwood-dockstar-initramfs-kernel.bin
bootz 0x800000
# detach if already attached
ubidetach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')
# scp openwrt-kirkwood-dockstar-squashfs-factory.bin /tmp
ubiformat -f /tmp/openwrt-kirkwood-dockstar-squashfs-factory.bin
# attach is important to resize rootfs_data otherwise it wont boot
ubiattach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49010
