With current uboot default configuration the bootloader will
fail to start the OpenWrt firmware with the following error:
-----
unexpected character 'b' at the end of partition
Error initializing mtdparts!
incorrect device type in ubi
Partition ubi not found!
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
Error occured, error code = 112
-----
If the uboot configuration is examined with printenv
I can see that mdtparts line (on a nsa310) is wrong:
-----
mtdparts=mtdparts=orion_nand:0x0c0000(uboot),
0x80000(uboot_env),0x7ec0000(ubi)bootargs_root=
----
The "bootargs_root=" that was appended to it should not be there.
Fix the issue by adding a \0 line terminator at the end of affected lines,
mimicking what is also done by uboot upstream.
This issue was detected and confirmed on a nsa310, nsa325 and
a pogoplug v4, but it's not hardware-specific, so apply the same fix
to other devices as well.
Note that the issue is with the uboot's integrated boot configuration,
which is not used unless the uboot configuration in flash is unavailable
(erased or corrupted), which happens only on first time installation,
or if the user deletes the uboot configuration when upgrading uboot.
People just upgrading from an older uboot without erasing their previous
uboot configuration stored in flash would not have noticed this issue.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Add a menuconfig option to set the HOME_URL exposed in
/usr/lib/os-release independent from the
LEDE_DEVICE_MANUFACTURER_URL.
Fixes: FS#1123
Signed-off-by: Mathias Kresin <dev@kresin.me>
dfd9827 version: bump snapshot
88729f0 wg-quick: android: prevent outgoing handshake packets from being dropped
1bb9daf compat: more robust ktime backport
68441fb global: use fast boottime instead of normal boottime
d0bd6dc global: use ktime boottime instead of jiffies
18822b8 tools: fix misspelling of strchrnul in comment
0f8718b manpages: eliminate whitespace at the end of the line
590c410 global: fix a few typos
bb76804 simd: add missing header
7e88174 poly1305: give linker the correct constant data section size
fd8dfd3 main: test poly1305 before chacha20poly1305
c754c59 receive: don't toggle bh
Compile-tested-for: ath79 Archer C7 v2
Run-tested-on: ath79 Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
After a very enlightening but unfortunately far too short exchange with Jes
we mutually agreed to drop the patches. They are unfortunately not ready
yet.
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Add xt_bpf modules to {kmod-ipt,iptables-mod}-filter.
Match using Linux Socket Filter. Expects a BPF program in decimal
format. This is the format generated by the nfbpf_compile utility.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Commit 61d57a2f88 adds ath10k LED
support, but doesn't add an option to actually enable it.
After enabling this option, a LED named ath10k-phy0 appears in sysfs,
and a trigger can be assigned to it. Since 60deb3cdef the default set
trigger is the tpt one.
Enable it by default, as most devices using ath10k chips shouldn't be
severely space-constrained. There are likely many devices that can
benefit from having it enabled, like my testing device.
Before:
text data bss dec hex filename
245311 8899 16 254226 3e112 ath10k_core.ko
After:
text data bss dec hex filename
245979 8899 16 254894 3e3ae ath10k_core.ko
Tested on a D-Link DAP-2695-A1 (ar71xx).
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use the tpt LED trigger for each created phy led. Ths way LEDs attached
to the ath10k GPIO pins are indicating the phy status and blink on
traffic.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Includes specific support for PH8(1e2d-0053) / ELS61(1e2d-005b) modules.
Note for ELS61, the serial driver changes from serial option(ttyUSB) to usb-cdc (ttyACM).
Two additional fixes in this commit resolve issues with ttyACM devices: -
* wwan.sh - sys-fs has a subdirectory indirection (*/tty/ttyACMx) which was not handled properly
* wwan.usb - dependent scripts were not included, so this never actually called proto_set_available for example (and relied on inadvertent call for ttyUSB case)
Signed-off-by: David Thornley <david.thornley@touchstargroup.com>
Replace 204-udhcpc_no_msg_dontroute patch by the upstream busybox fix
which removes the code which requires the server ID to be on local
network
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Enabling CONFIG_ATH10K_THERMAL on targets that don't have CONFIG_THERMAL
enabled in their kernel config causes build to fail due to missing
symbol THERMAL_EMERGENCY_POWEROFF_DELAY_MS. Add it to kmod-thermal.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The package is not being generated otherwise, which is fatal because
it is part of the subtargets default package set...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
0bc4230 version: bump snapshot
ed04799 poly1305: add missing string.h header
cbd4e34 compat: use stabler lkml links
caa718c ratelimiter: do not allow concurrent init and uninit
894ddae ratelimiter: mitigate reference underflow
0a8a62c receive: drop handshake packets if rng is not initialized
cad9e52 noise: wait for crng before taking locks
83c0690 netlink: maintain static_identity lock over entire private key update
0913f1c noise: take locks for ss precomputation
073f31a qemu: bump default kernel
bec4c48 wg-quick: android: don't forget to free compiled regexes
7ce2ef3 wg-quick: android: disable roaming to v6 networks when v4 is specified
9132be4 dns-hatchet: apply resolv.conf's selinux context to new resolv.conf
41a5747 simd: no need to restore fpu state when no preemption
6d7f0b0 simd: encapsulate fpu amortization into nice functions
f8b57d5 queueing: re-enable preemption periodically to lower latency
b7b193f queueing: remove useless spinlocks on sc
5bb62fe tools: getentropy requires 10.12
4e9f120 chacha20poly1305: use slow crypto on -rt kernels on arm too
Compiled-for: ar71xx, lantiq
Run-tested-on: ar71xx Archer C7 v2 & lantiq HH5a
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested on 8devices Jalapeno(ipq40xx)
Introduces following changes
* Fix: In ethtool.8, remove superfluous and incorrect \
* Fix: fix uninitialized return value
* Fix: fix RING_VF assignment
* Fix: remove unused global variable
* Fix: several fixes in do_gregs()
* Fix: correctly free hkey when get_stringset() fails
* Fix: remove unreachable code
* Fix: fix stack clash in do_get_phy_tunable and do_set_phy_tunable
* Feature: Add register dump support for MICROCHIP LAN78xx
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ecd954d530 installs specific interface triggers which rewrites the dnsmasq config
file and restarts dnsmasq if the network interface becomes active for which a trigger
has been installed.
In case no dhcp sections are specified or ignore is set to 1 dnsmasq will not be started
at startup which breaks DNS resolving.
Fix this by ditching the BOOT check in start_service and always start dnsmasq at startup.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This new package was missing the dependency to kmod-random-core which
caused some build errors.
Fixes: 163ab9135a ("kernel/modules: add chaoskey module, hardware TRNG")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package the driver for Chaoskey, a USB dongle that provides a
True Random Number Generator (TRNG) and feeds entropy to kernel.
Chaoskey driver is included the upstream Linux sources, so
only packaging it is needed.
Run-tested with ipq806x/R7800 and mvebu/WRT3200ACM.
(Requires CONFIG_HW_RANDOM kernel option.)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MiB Macronix MX25L12845EMI-12G
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Mode-toggle-switch
LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
(LAN not controllable by software)
(WLAN each green / red)
SERIAL: Header next to eth-phy.
VCC, TX, GND, RX (Square hole is VCC)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from tftp
- OpenWRT sysupgrade
- LEDs
- WPS Button
Not Working:
- Mode-toggle-switch
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.
append-cmdline patch taken from chunkeeys work on the NBG6617.
Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
While support for the FLOWOFFLOAD target is available in the firmware
images, it is still missing in some of the binary packages on
downloads.openwrt.org, e.g. for the mipsel_mips32 architecture.
Increment PKG_RELEASE to force an update of these packages.
Also adjust the package description to include the FLOWOFFLOAD target.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
The device tree files are now matching the kernel 4.17 and this will be
send also for integration into mainline U-Boot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch 220-add-sunxi50i-nanopi-neo-plus2.patch was merged upstream.
The u-boot-sunxi-with-spl.bin is now also created for the ARM64 sunxi
boards by U-Boot itself, no need to do it manually any more.
This was tested on a H2+ Orange Pi R1 and a H5 Orange Pi Zero Plus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update the link to the current section in the documentaion wiki.
This fixes https://github.com/openwrt/packages/issues/6282
Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
It was described by Arend as:
> This series is intended for 4.17 and includes following:
>
> * rework bus layer attach code.
> * remove duplicate variable declaration.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
9090f9c mt76x2: fix threshold for gain adjustment
2cbaa57 mt76x2: fix swapped values for RXO-18 in gain control
a39ab70 mt76x2: adjust AGC control register 26 based on gain for VHT80
4936c0c mt76x2: clear false CCA counters after changing gain settings
1528fe7 mt76x2: fix variable gain adjustment range
f3522e1 mt76x2: add a debugfs file to dump agc calibration information
65e161b mt76x2: fix tracking rssi for dynamic gain adjustment
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use vectoring firmware downloaded via vdsl_fw_install.sh from
ltq-vdsl-fw package for annex B and annex J.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Recent Speedport firmware downloads only work over HTTPS, so the user
either needs to provide the already downloaded file or install
ustream-ssl-* as well as ca-certificates or ca-bundle.
So to get VDSL2 with vectoring on xRX200, simply run
vdsl_fw_install.sh
on the target and either provide the downloaded file as instructed or
make sure the device is connected to the Internet and can download that
HTTPS url itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ucert is a wrapper around usign to allow delegation and revocation of
public keys for future use in sysupgrade.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This work was sponsored by WIO (wiowireless.com)
Ship EEPROM blobs for specific supported board only and don't have them
lurking around in our source tree but rather download them from
@github/RPi-Distro/firmware-nonfree upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
On bcm53xx and brcm47xx, commands are passed to default_do_upgrade that
expect the image to be passed on stdin, rather than as an argument.
Fixes: 30f61a34b4 ("base-files: always use staged sysupgrade")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fix condir option processing allowing to use the format
"<directory>[,<file-extension>......]," as documented on the dnsmasq man
page which previously resulted into bogus dir being created.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
On some targets this module depends on kmod-of-mdio.
This is similar to the fixes done in:
dc629d9cf5 ("kernel: fix kmod-switch-rtl8366-smi dependency")
56bd23cf52 ("kernel: let kmod-rtl8366-smi conditionally depend on kmod-of-mdio")
Fixes: 32f32398af ("kernel/modules: add kmod-mdio-gpio module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some ath10k firmware versions allow to access the chip internal a
temperature sensor and allow to reduce the amount of the time when the card
is allowed to send. The latter is required on devices which tend to
overheat.
An userspace service has to read
/sys/class/ieee80211/phy*/device/hwmon/hwmon*/temp1_input regularly and
then decide how much the device has to be throttled. This can be done by
writing to /sys/class/ieee80211/phy*/device/cooling_device/cur_state. By
default it is not throttled (0) but it can be throttled up to 100(%).
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Without this change, ifx_mei_atm_showtime_check() will always return
"showtime" after one call of MEI_InternalXtmSwhowtimeEntrySignal()
was done, even if MEI_InternalXtmSwhowtimeExitSignal() was called
in the meantime.
The ifx_mei_atm_showtime_check() function is used by the ltq-atm and
ltq-ptm driver.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Some of the ubi-tools in the upstream mtd-utils have been
broken by a bad patch upstream. It causes major breakage
during sysupgrade when the kernel, rootfs, ... volumes
are deleted in the wrong order.
This patch therefore reverts the faulty upstream commit which
fixes the bug.
linux-mtd mailing-list thread:
<http://lists.infradead.org/pipermail/linux-mtd/2018-June/081562.html>
Cc: John Crispin <john@phrozen.org>
Reported-by: L. Wayne Leach <LLeachii@aol.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This reverts a change made in Sep 2017 [1] which introduced
MSG_DONTROUTE flag to prevent udhcpc from reaching out to servers on a
different subnet. That change violates RFC2131 by forcing fully
configured clients, who got their configurations through an offer
relayed by a DHCP relay, from renewing through a unicast request
directly to the DHCP server, resulting in the client resorting to
boradcasting lease extension requests instead of unicasting them,
further breaking RFC2131.
The problem with MSG_DONTROUTE appears when talking to a properly
configured DHCP server that rejects non-compliant requests. Such server
will reject lease extension attempts sent via broadcast rather than
unicast, as is the case with Finnish ISPs Telia and DNA as well as
Estonian ISP Starman. Once the lease expires without renewal, udhcpc
enters init mode, taking down the interfaces with it, and thus causing
interruption on every lease expiry. On some ISPs (such as the ones
mentioned above) that can be once every 10-20 minutes. The interruptions
appear in the logs as such:
----
udhcpc: sending renew to x.x.x.x
udhcpc: send: Network unreachable
udhcpc: sending renew to 0.0.0.0
udhcpc: sending renew to 0.0.0.0
...
udhcpc: lease lost, entering init state
Interface 'wan' has lost the connection
Interface 'wan' is now down
Network alias 'eth0' link is down
udhcpc: sending select for y.y.y.y
udhcpc: lease of y.y.y.y obtained, lease time 1200
Network alias 'eth0' link is up
Interface 'wan' is now up
----
During lease extension, a fully configured client should be able to
reach out to the server from which it recieved the lease for extension,
regardless in which network it is; that's up to the gateway to find. [2]
This patch ensures that.
[1]
http://lists.busybox.net/pipermail/busybox-cvs/2017-September/037402.html
[2]
https://www.netmanias.com/en/post/techdocs/6000/dhcp-network-protocol/
understanding-dhcp-relay-agents
Signed-off-by: Adi Shammout <adi.shammout@outlook.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If log_file is specified, make sure its directory exists.
Signed-off-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
SourceForge is deprecated according to upstream, so switch to main site
for downloads.
Tested on Turris Omnia (mvebu).
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Problem - rapsberry pi 3 b/b+ does not boot with bcm2710 images!
How Raspberry Pi boots Actualy?
When Raspberry is switched on GPU is activated.
1. GPU execute First stage bootloader from ROM.
First stage bootloader mount the FAT boot partition on the SD card
and execute second stage bootloader (bootcode.bin).
2. Second stage bootloader (bootcode.bin) activate SDRAM.
Load the GPU firmware (start.elf).
3. GPU firmware (start.elf)
a) display Rainbow splash.
b) read firmware configuration file config.txt and
split the RAM using fixup.dat.
c) loads a cmdline.txt
d) enables the CPU.
e) loads the kernel image configurable via config.txt
In your target/linux/brcm2708/image/config.txt
493 ## kernel (string)
494 ## Alternative name to use when loading kernel.
495 ##
496 #kernel=""
it is not configured!
But in your target/linux/brcm2708/image/Makefile
75 KERNEL_IMG := kernel8.img
76 DEVICE_TITLE := Raspberry Pi 3B/3B+
you have kernel8.img
GPU Firmware search order by default for a PI 3 is:
kernel8.img if found boot in 64 bit mode
kernel8-32.img if found boot in 32 bit mode
kernel7.img if found boot in 32 bit mode
kernel.img if found boot in 32 bit mode
But a PI 2 will start the search from kernel7.img and
a PI 1 only looks for kernel.img.
Оbviously the kernel has been found.
But something goes wrong and the device is restarted.
In your package/kernel/brcm2708-gpu-fw/Makefile
11 PKG_NAME:=brcm2708-gpu-fw
12 PKG_VERSION:=2017-08-08
13 PKG_RELEASE:=e7ba7ab135f5a68b2c00a919ea9ac8d5528a5d5b
boot loader is 10 monts old.
In conclusion, the best way to solve the problem is
to update the boot loader!
Fixup_cd.dat and start_cd.elf files are not necessary.
These are used when GPU memory is set to 16 MB, which disables
some GPU features.
I did not remove them just in case!
cheers
Signed-off-by: Christo Nedev <christo.nedev@gmail.com>
5699354 extensions: fix build failure on fc28
e6359ee build: update ebtables.h from kernel and drop local unused copy
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
There are several long-standing issues present in the UCI shell API as
documented in https://wiki.openwrt.org/doc/devel/config-scripting. They
relate both to high-level, user-defined callback functions used to
process UCI config files, and also to low-level functions used within
scripts generally.
The related problems have been encountered now and in the past, e.g.
https://forum.openwrt.org/viewtopic.php?id=54295, and include:
a) UCI parsing option() function and user-defined option_cb() callbacks
being erroneously called during processing of "list" config file entries;
b) normal usage of the low-level config_set() unexpectedy calling any
defined option_cb() if present; and
c) handling of the list_cb() not respecting the NO_CALLBACK variable.
Root causes include a function stack "inversion", where the low-level
config_set() function incorrectly calls the high-level option() function,
intended only for processing the "option" keyword of UCI config files.
This change addresses the inversion and other issues, making the option
handling code more consistent and smaller, and simplifying developers'
usage of UCI callbacks.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
20c0766 mt7603: adjust rx hang watchdog for MT7628
664e321 mt7603: add extra PSE hang check signature for MT7628
f24b56f update MT7628 firmware to the latest version
d87e4b0 mt7603: clear PSE reset bit if PSE reset fails
0ef26ef mt76: only stop tx queues on offchannel, not during the entire scan
f399da3 mt76: prevent tx scheduling during channel change
21c1e1e mt76: move ieee80211_hw allocation to common core
730c292 mt76: wait for pending tx to complete before switching channel
fcbb49e mt76x2: use udelay instead of usleep_range in mt76x2_mac_stop
792dbe0 mt7603: do not hold dev->mutex while flushing dev->mac_work
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501.
Setting the uci parameter encaplimit to ignore; allows to disable the insertion
of the destination option header in the map-e packets.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit uci parameter accordingly.
If no encaplimit value is specified the default value is 4 as before.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501 for dynamic created ds-lite/map
interfaces.
Setting the uci parameter encaplimit_dslite/map to ignore; allows to disable the insertion
of the destination option header for the dynamic created ds-lite/map interface.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit_dslite/map uci parameter accordingly.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501.
Setting the uci parameter encaplimit to ignore; allows to disable the insertion
of the destination option header in the ds-lite packets.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit uci parameter accordingly.
If no encaplimit value is specified the default value is 4 as before.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.
Functional issues:
* PCIe won't come up (hence no USB3 on Shuttle KD20)
* I2C bus of Akitio myCloud device is likely not to work (missing
debounce support in new pinctrl driver)
Code-style issues:
* plla/pllb needs further cleanup -- currently their users or writing
into the syscon regmap after acquireling the clk instead of using
defined clk_*_*() functions to setup multipliers and dividors.
* PCIe phy needs its own little driver.
* SATA driver is a monster and should be split into an mfd having
a raidctrl regmap, sata controller, sata ports and sata phy.
Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Do not set device runtime property on interfaces in the hotplug handler
and in fixup_interfaces(). This property conflicts with device option
in several proto handlers (mainly QMI and other WWAN/3G protos) and does
not seem to be used anywhere.
Signed-off-by: Ivan Shapovalov <intelfx@intelfx.name>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
3.4 is mainly a bug fix/maintenance release.
3KB increase in ipk lib size on mips.
Compile tested for: ar71xx, ramips
Run tested on: ar71xx Archer C7 v2, ramips mir3g
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The mtd tool is built with different configurations depending on the
target. For example, brcm47xx adds the fixtrx subcommand, without which
an image fails when booting the second time.
Mark the mtd package as nonshared to really fix FS#484.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
This version bump was made upstream mostly for OpenWRT, and should fix
an issue with a null dst when on the flow offloading path.
While we're at it, Kevin and I are the only people actually taking care
of this package, so trim the maintainer list a bit.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Clean up conflicts/provides/depends hell and add PROVIDES for
eapol-test variants while at it.
Update mesh-DFS patchset from Peter Oh to v5 (with local fixes) which
allows to drop two revert-patches for upstream commits which previously
were necessary to un-break mesh-DFS support.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Implicetely selecting the required options via Kconfig snippet from
hostapd worked fine in local builds when using menuconfig but confused
the buildbots which (in phase1) may build wpad-mini and hence already
come with CONFIG_WPA_WOLFSSL being defined as unset which then won't
trigger changing the defaults of wolfssl.
Work around by explicitely reflecting wpa_supplicant's needs in
wolfssl's default settings to make buildbots happy.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While building, curl complains that the path specified is missing.
Also, without ca-bundle, something like 'curl https://www.google.com'
does not work due to a certificate verify error.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
It simplifies the Makefile a bit. In addition, using ca-bundle
saves some space as well.
It also fixes an issue with at least transmission, which has a dependency
on ca-bundle, but currently libcurl with OpenSSL or GnuTLS cause it not
to work.
This has been tested on mt7621 with OpenSSL and GnuTLS just by running
'curl https://www.google.com' and seeing if there's a verify error.
The rest are already using ca-bundle and therefore work fine.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Import a revert-commit from Stanislaw Gruszka which significantly
improves WiFi performance on rt2x00 based hardware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently when installing the firmware, a bunch of files and directories
that the ath10k driver does not look for are created.
The package now installs firmware for both hw 2.1 and 3.0 devices.
2.1 is abandonware but may be useful to keep.
3.0 firmware was tested on a Killer 1535 to be relatively stable with
802.11w disabled. 802.11w causes multiple firmware crashes but that's true
of other ath10k firmwares as well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This change will trigger rebuild on buildbots in case of changed config
symbols, like in the case of hostapd selecting some wolfssl symbols
lately.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of selecting the SSL provider at compile time, build package
variants for each option so users can select the binary package without
having to build it themselves.
Most likely not all variants have actually ever been user by anyone.
We should reduce the selection to the reasonable and most used
combinations at some point in future. For now, build them all.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
dd02dad fstools: allow the mounting with full access time accounting
242248c fstools: allow to compress the filesystem
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The previous refactoring of ucidef_set_interface() removed the protocol
selection heuristic which breaks the networking defaults for the majority
of boards.
Re-add the protocol selection and rename two bad "proto" references to
the expected "protocol" value.
Fixes: 85048a9c1f ("base-files: rework _ucidef_set_interface to be more generic")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support for building wpa_supplicant/hostapd against wolfssl has been
added upstream recently, add build option to allow users using it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use download from github archive corresponding to v3.14.4 tag because
the project's website apparently only offers 3.14.0-stable release
downloads.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
commit 39a6ce205d (ustream-ssl: Enable ECDHE with OpenSSL.) broke
build against wolfSSL because wolfSSL doesn't (yet) support
SSL_CTX_set_ecdh_auto() of the OpenSSL API.
Fix this in ustream-ssl:
189cd38b41 don't use SSL_CTX_set_ecdh_auto with wolfSSL
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mounting using the zlib compression and mounting with
full access accounting are now available in the
menuconfig.
Signed-off-by: Pierre Lebleu <pme.lebleu@gmail.com>
This reverts commit a03035dad1
as it has several issues:
-Host file is located in a directory which is not unique per dnsmasq instance
-odhcpd writes host info into the same directory but still sends a SIGHUP to dnsmasq
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This is a rework of previously submitted patch reworking
ucidef_set_interface_raw [1]. Here, keep the idea but instead
make _ucidef_set_interface more generic and use it instead of
ucidef_set_interface_raw.
Also change the users like ucidef_set_interface_lan and others.
[1] https://patchwork.ozlabs.org/patch/844961/
Signed-off-by: Roman Yeryomin <roman@advem.lv>
1.) "addn-hosts" per default point to a file (but it supports directory)
2.) "hostsdir" only support directory with the additional benefit: New or changed files are read automatically.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This makes mbedtls use the POSIX API directly and not use the own
abstraction layer.
The size of the ipkg decreased by about 100 bytes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This make sit possible to store informations about a session and reuse
it later. When used by a server it increases the time to create a new
TLS session from about 1 second to less than 0.1 seconds.
The size of the ipkg file increased by about 800 Bytes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The soversion was changed in this version again and is now aligned with
the 2.7.2 version.
The size of the ipkg file stayed mostly the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
As of commit in kernel:
6104c37094 fbcon: Make fbcon a built-time depency for fbdev
framebuffer console is build in into framebuffer module and there's no
standalone fbcon module. Therefore drop the kmod-fbcon and enable
console in kmod-fb. The only targets which use these modules are imx6
and geode, both are on kernel 4.14 so no fallback for other kernels is
introduced.
Being at that this commit also fixes autoload of fbdev for x86.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This now matches what was generated locally on my PC and the file on the
mirror server.
Fixes: 349fe46103 ("ath10k-firmware: Update QCA988X firmware to the latest version")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* chacha20poly1305: add mips32 implementation
"The OpenWRT Commit" - this significantly speeds up performance on cheap
plastic MIPS routers, and presumably the remaining MIPS32r2 super computers
out there.
* timers: reinitialize state on init
* timers: round up instead of down in slack_time
* timers: remove slack_time
* timers: clear send_keepalive timer on sending handshake response
* timers: no need to clear keepalive in persistent keepalive
Andrew He and I have helped simplify the timers and remove some old warts,
making the whole system a bit easier to analyze.
* tools: fix errno propagation and messages
Error messages are now more coherent.
* device: remove allowedips before individual peers
This avoids an O(n^2) traversal in favor of an O(n) one. Before systems with
many peers would grind when deleting the interface.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Use ft_psk_generate_local=1 by default, as it makes everything else fairly
trivial. All of the r0kh/r1kh and key management stuff goes away and hostapd
fairly much does it all for us.
We do need to provide nas_identifier, which can be derived from the BSSID,
and we need to generate a mobility_domain, for which we default to the first
four chars of the md5sum of the SSID.
The complex manual setup should also still work, but the defaults also
now work easily out of the box. Verified by manually running hostapd
(with the autogenerated config) and watching the debug output:
wlan2: STA ac:37:43:a0:a6:ae WPA: FT authentication already completed - do not start 4-way handshake
This was previous submitted to LEDE in
https://github.com/lede-project/source/pull/1382
[dwmw2: Rewrote commit message]
Signed-off-by: Gospod Nassa <devianca@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
e59f925 hardware: add device ids for QCA9984, 88W8887 and 88W8964 radios
2a82f87 nl80211: back out early when receiving FAIL-BUSY reply
77c32f0 nl80211: fix code calculating average signal and rate
Signed-off-by: John Crispin <john@phrozen.org>
Drop package/network/services/wireguard/patches/100-portability.patch
Instead pass 'PLATFORM=linux' to make since we are always building FOR
linux.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Add needed firmware for newer QCA Rome Bluetooth family.
This enables use of bluetooth with ath3k driver on QCA9377/9378 devices.
Signed-off-by: Robert Marko <robimarko@gmail.com>
