mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.
Signed-off-by: Claudio Leite <leitec@gmail.com>
buildbot fails to build without regmap, which I couldn't reproduce locally.
Hopefully this fixes it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
64 bit support for Raspberry Pi 3 is experimental. However, bcm2709 subtarget
should serve as a stable and compatible 32 bit support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds support for Raspberry Pi 3 on the bcm2709 subtarget, in order to
keep 32 bit image support when 64 bit support is added on bcm2710 subtarget.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Initial idea was to use package with this PHY driver for devices that
need it. Unfortunately this can't work as bgmac is built-in and PHY
probing happens before loading modules - it results in PHY subsystem
picking default (generic) PHY driver.
There were two ways of solving this:
1) Making bcm53xx use bgmac as module
xor
2) Built-in Broadcom PHY driver
After some quick discussion it seems we can simply built-in the driver
as increased kenel size is relatively small (1805 B).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
These are patches queued for 4.11. It adds support for even more hw and
removes some annoying WARN_ONCE.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's needed for macaddr_add.
Fixes: 50efd403e6 ("bcm53xx: set WAN MAC address to don't share one with LAN interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.
Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It just makes code consistent. This trivial change may be a 17.01
candidate to provide simpler backporting experience.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In kernel 4.9 it's already present so we don't want to overwite it (with
older & API incompatible version).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked
broken, except arc770 and arch38 due to broken toolchain.
Runtime-tested on ar71xx, octeon, ramips and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.
Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.
The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).
If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.
Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The factory image can't be bigger than 3328 KByte. If the image is
bigger than that, the gemtek-header tool throws an error and breaks
the build.
Make sure the output file to which the gemtek header should be added
exists and wasn't removed during the check-size step because of it
size. This will prevent hard errors in case the factory image is to big
similar to what is done for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.
Fixes: FS#451
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
After analyzing numerous NVRAMs and vendor firmwares it seems the base
MAC address is used for LAN interface. WAN interface has different one
which sometimes is set directly in NVRAM and sometines needs to be
calculated.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
