This is needed for the definition of $(LINUX_DIR). This is used in
u-boot.mk to change the device-tree compiler to the dtc used by
linux.
Without this, the build will use the system dtc. This results in a
build failure when a dtc does not exist outside the buildroot.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
stop() is overwritten by rc.common, so implement stop_service instead.
While at it, remove the now unnecessary restart() override
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch splits `kmod-mt76` into three separate packages:
`kmod-mt76-core`, `kmod-mt76x2` and `kmod-mt7603`. By making
`kmod-mt76` a metapackage containing these new packages,
the previous behaviour of including all drivers and firmware
is left unchanged, unless explicitly unselected in
`DEVICE_PACKAGES`.
This splitting is especially beneficial for devices with
small flash chips, since the `kmod-mt76` package currently
requires ~160K on squashfs (after compression).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
Update to latest Git head to get rid of a stray printf() causing unwanted
output in the "opkg list-upgradable" command.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
--bogus-priv now applies to IPv6 prefixes as specified in RFC6303 - this
is significantly friendlier to upstream servers.
CNAME fix in auth mode - A domain can only have a CNAME if it has no
other records
Drop 2 patches now included upstream.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
A missing list pointer initialization caused opkg to ignore conffile entries
from status files, breaking the conffile tracking on the target.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
c553354 cmake: fix typo
8973576 kmodloader: fix not being able to find some modules
fce9382 cmake: Check for getrandom system call
Signed-off-by: Felix Fietkau <nbd@nbd.name>
px5g-standalone only supports SHA1 for certificates, which is strongly
deprecated. The new px5g-standalone is about 27k bigger (compressed),
and has identical behavior to px5g-mbedtls (it uses SHA256).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The switch to cmake caused the -DHAVE_USIGN flag to get lost, disabling
compilation of the correspondinf support code.
Update to latest Git head which enables usign support by default.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This reverts commit cc66f819b4.
This commit causes opkg to install px5g-standalone instead of px5g when
installing luci-ssl. As luci-ssl depends on mbedtls, using
px5g-standalone makes no sense. Next to that, it creates deprecated SHA1
certificates. Revert the commit to avoid pxg5-standalone to be
installed by accident.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
- Fix eap test to work with standalone hostapd builds
- Fix 11n test to check the correct define
- Add 11ac, 11r and 11w tests
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
New test release (since test1) includes 2 LEDE patches that are
upstream and may be dropped, along with many spelling fixes.
Add forthcoming 2017 root zone trust anchor to trust-anchors.conf.
Backport 2 patches that just missed test3:
Reduce logspam of those domains handled locally 'local addresses only'
Implement RFC-6842 (Client-ids in DHCP replies)
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Specifying USE_PRIVATE_LIBGCC is no longer needed, as it is the
default.
Patch 001 is removed, since it was already merged upstream. Patches
100 and 101 are removed because they do not appear to be needed
anymore, and they do not conform with the sign-off and commit message
procedures.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Because they were hidden, there was no way to disable the uboot
targets in menuconfig, so they had to be built every time. The omap
target is the only one to hide uboot packages. To be consistent with
the other targets, and have more control over the build, un-hide the
u-boot packages.
Note that the default behavior remains unchanged, as uboot will be
built unless explicitly disabled.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Switch to our own fork of opkg to significantly reduce the required amount
of memory when updating lists or installing packages.
Preliminary tests showed a usage drop of about 90% during these operations,
from ~3.7MB with unmodified opkg to ~360KB with our custom fork.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Removing redundant spaces from the name of the option. Without fix:
root@LEDE:~# opkg install ugps
Installing ugps (2016-10-24-32a6b2b7-1) to root...
Downloading http://downloads.lede-project.org/releases/17.01-SNAPSHOT/packages/mips_24kc/base/ugps_2016-10-24-32a6b2b7-1_mips_24kc.ipk
Configuring ugps.
uci: Parse error (invalid character in name field) at line 3, byte 23
uci: Parse error (invalid character in name field) at line 3, byte 23
sh: out of range
root@LEDE:~# uci show gps
uci: Parse error (invalid character in name field) at line 3, byte 23
With this fix:
root@LEDE:~# uci show gps
gps.@gps[0]=gps
gps.@gps[0].tty='ttyACM0'
gps.@gps[0].adjust_time='1'
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
This update includes numerous small fixes for:
1) Interfaces setup
2) Packets parsing
3) Sending replies
Without this there were multiple problems with exchanging information
between (u)mdns and other implementations (including (u)mdns as well).
This also follows project rename to umdns which was required to avoid
confusion with Apple's mdnsd from mDNSResponder project.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
5f91241 procd: add cancel_timeout on rc scripts when a runtime_timeout is specified
961dc69 procd: stop service using SIGKILL if SIGTERM failed to do so
Signed-off-by: John Crispin <john@phrozen.org>
Default trigger action timeout was added to procd.sh in commit f88e3a4c0
(procd: add default timeout for reload trigger actions)
However, the timeout value was not placed under the correct JSON-script
array nesting level and thus did not apply.
To fix this and make the timeout actually apply to the reload triggers,
we place it in the correct scope, that is the per-trigger array.
Fixes: f88e3a4c0a
Signed-off-by: Denis Osvald <denis.osvald@sartura.hr>
This can be used to tweak the buildbot behavior without having to change
buildbot's configuration.
It will also allow us to add more aggressive clean steps (e.g. on
toolchain changes), which would break developers' workflows if enable
by default.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
fixes issue "nsa 310b u-boot can initialize usb but cannot
use usb storage so it cannot load files from usb"
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
as we do for IPv4 PPP interfaces. When we create the
dynamic IPv6 interface we should inherit ip6table from
main interface.
Signed-off-by: Ulrich Weber <ulrich.weber@riverbed.com>
pppoe-discovery performs the same discovery process as pppoe, but does
not initiate a session
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
When running wifi detect, the user will be told on error output that
wifi detect is deprecated, that wifi config must be used instead. Also
the commit that changes it is referenced for further info.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
Since commit 5f8f8a3661 wifi detect does
not longer work and wifi config it's used to configure not yet
configured wireless devices.
This commit changes command usage to reflect that change.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
f107656 netifd: Add option to configure locktime for each device
cdc0e80 interface: add prefix assignment priority support
6397f5e device: add veth support
6228d0f wireless: fix _wireless_add_process
7cc2f10 treewide: fix white space errors
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Effects of the bugs could include memory corruption, tx hangs, kernel
crahes, possibly other things as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Important change was made in 1.0.18: all sub-libs were merged
in one and only libc similarly to musl.
See [1] for more details.
To support that we had to remove refences to those sub-libs like
libpthread, libcrypt, libdl, libm, libutil etc.
[1] http://cgit.uclibc-ng.org/cgi/cgit/uclibc-ng.git/commit/?id=29ff9055c80efe77a7130767a9fcb3ab8c67e8ce
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
The only HMACs currently available use MD5 and SHA1, both of which have known
weaknesses. We already compile in the SHA256 code since we use Curve25519
by default, so there's no significant size penalty to enabling this.
Signed-off-by: Joseph C. Sible <josephcsible@users.noreply.github.com>
Remove CONFIG_VLAN_8021Q overrides for two targets
These features are built into the kernel image for all targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When calling erase() on a containers derived from __base_associative
(e.g. multimap) and providing a pair of iterators a segfault will
occur.
Example code to reproduce:
typedef std::multimap<int, int> testmap;
testmap t;
t.insert(std::pair<int, int>(1, 1));
t.insert(std::pair<int, int>(2, 1));
t.insert(std::pair<int, int>(3, 1));
t.erase(t.begin(), t.end());
Signed-off-by: Ben Kelly <ben@benjii.net>
Goflexhome/net use uImage, and to boot an uImage the u-boot
must use bootm command, not bootz.
Fixes the "i cannot boot LEDE with this u-boot" issue that I
found out myself with my goflexnet.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
all patches for CONFIG_SYS_GENERIC_BOARD are obsolete for
uboot 2016 sources.
Run-tested with the uboot of goflexnet, also the md5sum of
all other uboots is the same with or without these patches.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* Update to 1.43.4
* Use xz tarball which saves about 2Mbyte in size
Changelog: http://e2fsprogs.sourceforge.net/e2fsprogs-release.html#1.43.4
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [use @KERNEL instead of hardcoded URL]
This commit combines all the changes I've made on my staging tree
into a single commit fixing many issues with our patch for MT7620.
First of all, checkpatch.pl revealed numerous code style issues with
the patch, so fix all the white-space and commets. Also use
usleep_range instead of legacy timing and relax timing for VCO
calibration just like the vendor driver does.
Several line programming registers were commented out in the patch.
Originally this came from the features present but disabled by default
in the vendor's driver (RTMP_TEMPERATURE_CALIBRATION and
ADJUST_POWER_CONSUMPTION_SUPPORT). Remove the dead code for now, it can
easily be re-added if we actually intend to support those features.
Move values from mt7620_freqconfig type into the existing rf_channel
struct, this shouldn't be a new typedef and it is possible to use the
existing struct because rf_channel got 4 32-bit fields, so two of the
8-bit values from mt7620_freqconfig can easily be stored in the same
32-bit field.
Map values such that
Rdiv -> rf1
N -> rf2
K -> rf3[0:7]
D -> rf3[8:15]
Ksd -> rf4
This makes the channel switching logic already look a bit more like
what we are used to in rt2x00... Probably many of the read-modify-write
calls could still be replaced by macros intended for that.
iq calibration seems to be identical to RT5592, so just enable it.
Test shows that this improves things quite a lot, datarates went up
by a couple of megabits when running iperf, signal quality seems jumpy
in the first few seconds once a station connencts, the stabelizes on a
value significantly better than what it was before.
Add description to the patch and reference the original OpenWrt commit
by which it was added.
The patch now passes checkpatch.pl and can thus be discussed with the
upstream authors of the rt2x00 driver.
Funded-by: https://www.kickstarter.com/projects/1327597961/better-support-for-mt7620a-n-in-openwrt-lede/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Bump to dnsmasq 2.77test1 - this includes a number of fixes since 2.76
and allows dropping of 2 LEDE carried patches.
Notable fix in rrfilter code when talking to Nominum's DNS servers
especially with DNSSEC.
A patch to switch dnsmasq back to 'soft fail' for SERVFAIL responses
from dns servers is also included. This mean dnsmasq tries all
configured servers before giving up.
A 'localise queries' enhancement has also been backported (it will
appear in test2/rc'n') this is especially important if using the
recently imported to LEDE 'use dnsmasq standalone' feature 9525743c
I have been following dnsmasq HEAD ever since 2.76 release.
Compile & Run tested: ar71xx, Archer C7 v2
Tested-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ref commit 9525743c07
dnsmasq: make DHCPv6 viable for standalone dnsmasq install
Above commit broke instancing by missing filter_dnsmasq()
as part of the dhcp_add() execution.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Do not spam the syslog with DHCPv6 lease info if quietdhcp option
is selected. This already works for DHCPv4, make it work in the same
way for DHCPv6.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
[Originally written by Arjen de Korte on GitHub but had issues providing
a SoB in correct format.]
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Adds the following fixes:
91acde6 libubus: do not modify uloop_cancelled
763b9b2 libubus: reset ctx->sock.eof to fix reconnect issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adds the following changes:
de3f14b uloop: add uloop_cancelling function
3b6181b utils: fix build on Mac OS X 10.12
7f671b1 blobmsg: add support for double
0fe1374 utils: add helper functions useful for allocating a ring buffer
8fc1c30 libubox: replace strtok with _r version.
4a9f74f libubox: allow reading out the pid of uloop process in lua
372e1e6 uloop: remove useless epoll data assignment
f9db1cb libubox: allow reading out the remaining time of a uloop timer in Lua
Signed-off-by: Felix Fietkau <nbd@nbd.name>
key_direction shows up as an openvpn option in the user-interface but does not end up in the /var/etc/openvpn*.conf file. Adding it to the list here fixed the issue for me.
Signed-off-by: Brandon Koepke <bdkoepke@fastmail.com>
Update ubox to latest Git HEAD in order to import the following fixes:
ac2d43e kmodloader: support '-q' quiet option
f8d3d16 ubox: Add an option for more accurate timestamps in log
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Lots of users try random stuff when they encounter any kind of
difficulty. I've had to debug a number of cases where people had enabled
this option for no reason. Hopefully this warning will reduce the number
of useless support cases.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
I needed a moment to figure out relation between this patchset and the
nl80211: fix validation of scheduled scan info for wowlan netdetect
It appears nl80211 commit will go on top of brcmfmac changes so it's
safe to backport these patches.
One patch that was excluded is commit 2a2a5d1835b6 ("brcmfmac: add
.update_connect_params() callback") as it depends on missing commit
088e8df82f91 ("cfg80211: Add support to update connection parameters").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
samba.org has started to enforce https and
currently plain http downloads with curl/wget fail,
so convert samba.org download links to use https.
Modernise links at the same time.
Also convert samba.org URL fields to have https.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
dnsmasq has sufficient services to meet the needs of DHCP
and RA with IP6 for single router router users. This is
the most common use for consumer routers. Its reenforced
as most ISP tend to only DHCP-PD /64. dnsmasq has year
over year demonstrated great flexibility in its option
set, and support for off-standard DHCP clients.
odhcpd has enhanced capabilities focused on IP6 such
as DHCP/RA relay and NDP proxy. However, it is not as
flexible in its option set. odhcpd is not as forgiving
with off-standard DHCP clients. Some points may represent
a long term TODO list, but it is the state currently.
These changes make any such combination possible. Already
odhcpd can be set as the main dhcp server. Now odhcpd
can be removed or disabled and dnsmasq will take over
if DHCPv6 compiled in. The existing DHCPv6 and RA UCI
are translated into dnsmasq.conf. The changes focus on
'--dhcp-range', '--dhcp-host', and '--dhcp-options'.
DHCP host ID is least 16 bits [::1000-::FFFF], but
leaves low range for typical infrastructure assignments.
dnsmasq accepts DHCPv6 options in the tranditional
'--dhcp-option' put they must be prefixed 'option6:'.
dnsmasq will also discover SLAAC DNS entries from DHCPv4
clients MAC, and confirm with a ping at least renew.
Long term TODO include improving use of dnsmasq relay
options for DHCPv4 and DHCPv6 in parallel. It would also
be possible to preconfigure DHCP-PD in host-with-options
records for fixed infrastructure.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
[Jo-Philipp Wich: emit proper IPv6 hostid format in dhcp-host directive]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
ref commit 612e2276b4
ref commit ec63e3bf13
'option add_local_hostname' scripted implementation statically assigns
this host in auto generated host file at init. If IFUP or other signals
do not occur, then address changes are not tracked. The script doesn't
apply all the addresses at an interface. This may make logs obscure.
The script only puts the bare host name (maybe not FQDN) in host file,
but if '--exapandhosts' is enabled, then /etc/hosts entries will be
suffixed, and "127.0.0.1 localhost" becomes "localhost.lan".
dnsmasq provides an option to perform this function, but it is rather
greedy. '--interface-name=<name>,<iface>' will assign the name to all
IP on the specified interface (except link local). This is a useful
feature, but some setups depend on the original restrictive behavior.
'option add_local_fqdn' is added to enhance the feature set, but
if not entered or empty string, then it will default to original
option and behavior. This new option has a few settings. At each
increased setting the most detailed name becomes the PTR record:
0 - same as add_local_hostname 0 or disabled
1 - same as add_local_hostname 1
2 - assigns the bare host name to all IP w/ --dnsmasq-interface
3 - assigns the FQDN and host to all IP w/ --dnsmasq-interface
4 - assigns <iface>.<host>.<domain> and above w/ --dnsmasq-nterface
'option add_wan_fqdn' is added to run the same procedure on
inferred WAN intefaces. If an interface has 'config dhcp' and
'option ignore 1' set, then it is considered WAN. The original
option would only run on DHCP serving interfaces.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Instead of only using tagged CPU port configurations when more than one VLAN
is present on the switch, always emit tagged configurations unless a board
explicitely opts out of this behaviour by using the previously introduced
[0-9]u@netdev syntax.
Emitting default tagged configurations has the following benefits:
- Relation of switch vlans to netdevs is easier to understand, especially
for multi-cpu-port switches
- Adding additional VLANs (e.g. to break out a LAN port for other purposes)
becomes easier as users are not forced to change the existing untagged
VLAN to tagged and the existing ifname notation from ethX to ethX.Y
anymore, drastly reducing the likelyhood of soft-bricks.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes firmware crash in rare cases and a bug
ath10k_pci 0001:01:00.0: received unexpected tx_fetch_ind event: in
push mode
for those who kept experiencing it after previous firmware update.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Uses upstream code to parse DT supported band/frequency information.
Update existing .dts files to the new format and remove unnecessary
overrides.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
And, update support for 9880 chipsets. The new firmware
fixes a regression with EAPOL 4/4 packets added in
a recent commit.
It also fixes a case where the firmware would improperly try
to use STBC when configured for 1x1 (as 9887 always is).
Signed-off-by: Ben Greear <greearb@candelatech.com>
The driver had a bug when calculating the rateset. This resolves
that and allows full VHT mcs rates on 2x2 hardware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Some debugging/error messages are printed using wpa_printf and this
change allows finally reading them out of the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This will allow starting hostapd with the new -s parameter and finally
read all (error) messages from the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
wash, mpu & some memory optimisation have now made it to the official
cake repository.
Point LEDE to the official repository.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
c13b6a0 dhcpv6: fix white space error
e9d80cc dhcpv6: trigger restart of DHCPv6 state machine when not
receiving statefull options
c7122ec update README
419fb63 dhcpv6: server unicast option support
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The condition is always true due to the literal string followed the
-n test parameter. A model name set by target scripts always gets
overwritten this way.
Change the condition to check for an already existing destination file
as it was before 5e85ae9 ("base-files: fix error message during boot").
Signed-off-by: Mathias Kresin <dev@kresin.me>
It wasn't possible to read hostapd wpa_printf messages unless running
hostapd manually. It was because hostapd was printing them using vprintf
and not directly to the syslog.
We were trying to workaround this problem by redirecting STDIN_FILENO
and STDOUT_FILENO but it was working only for the initialization phase.
As soon as hostapd did os_daemonize our solution stopped working.
Please note despite the subject this change doesn't affect debug level
messages only but just everything printed by hostapd with wpa_printf
including MSG_ERROR-s. This makes it even more important as reading
error messages can be quite useful for debugging.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes build issues with some toolchains that don't add lcrypt in the default
search paths:
CMakeFiles/rpcd.dir/session.c.o: In function `rpc_login_test_password':
build_dir/target-mipsel-linux-gnu/rpcd-2016-12-03-0577cfc1/session.c:823: undefined reference to `crypt'
collect2: error: ld returned 1 exit status
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Some toolchains will produce executables with an interpreter that is e.g:
ld.so.1 (typically a symbolic link). Due to our current LIBC_SPEC_FILE value,
we would not be able to copy this symbolic link/file over to the rootfs and
executables would fail to load. Extend the search pattern to include all
ld*.so* files that could be needed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Refresh patches, delete patches that have been applied upstream.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix defaults]
The "new style" busybox applet approach moves all config and build
definitions related to an applet to its .c file. This makes the
patches easier to maintain, as they only add new files to the busybox
build directory, without modifying BusyBox files.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This fixes the following security problems:
CVE-2017-3731: Truncated packet could crash via OOB read
CVE-2017-3732: BN_mod_exp may produce incorrect results on x86_64
CVE-2016-7055: Montgomery multiplication may produce incorrect results
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not put the apex images into the kernel build directory as this directory
might get removed after kernel updates while the apex packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing u-boot images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This adds support for the PCB LEDs and Reset Button found on the PC
Engines APU2/APU3 embedded boards.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Updates to openvpn.init were included in early OpenVPN 2.4 patch
series, but got lost along the way and were never merged.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
HTB and TBF are the basic traffic shapers used by sqm-scripts. Moving
these into kmod-sched-core enables sqm-scripts to downgrade its
dependency from kmod-sched to kmod-sched-core, potentially making it
useful on devices with smaller flash sizes.
This adds around 30k to the size of kmod-sched-core (20k for sch_htb.ko
and 10k for sch_tbf.ko).
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This adds support for the SuperIO chip nct5104d found on the PC Engines
APU boards, which allows for a handful of additional ports, such as 2x
additional UART pinouts, enabling an external watchdog (no driver for
this functionality yet), and 16 GPIO pins. More info can be found at
https://pcengines.ch/ht_gpio.htm
Thanks to @feckert for helping package this.
Cc: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The name will appear in shell prompt and LuCI page title. Uppercase
letters seem to be more vigorous
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Update ubox to latest Git head in order to import the following fixes:
14839f0 kmodloader: make insert_module() idempotent
6e3c6dc kmodloader: add module alias awareness
9371411 kmodloader: fix out-of-bound access when parsing .modinfo
a62c946 kmodloader: modprobe: skip possible command line arguments
46a4b5f kmodloader: log to kmsg when loading directories of modules
eacc426 kmodloader: remove redundant glob wildcard char
8488bb5 ubox: Initialize conditionally uninitialized variable
db070f1 ubox: Fix some memory leaks
acc48b5 kmodloader: Fix typo in error message
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is how other Linux distributions are doing and kernel
modprobe_path[] of request_module() also has a default value of
/sbin/modprobe
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
A given signal-name is now converted to the corresonding number. In general
it's good style to use names (readability) and it's more portable: signal
numbers can be architecture-dependent, so we are more safe giving names.
A real world example is signal 10, which is BUS on ramips and USR1 on PPC.
All users of 'procd_send_signal' must change their code to reflect this.
Signed-off-by: Bastian Bittorf <bb@npl.de>
When relying on x.509 certs for auth and / or encryption of traffic you can't
use package openvpn-nossl.
Just have your package depend on openvpn-crypto to have SSL-encryption and
X.509-support enabled in OpenVPN. If encryption / X.509 is not a must, use
virtual packge openvpn, which is provided by all OpenVPN-variants.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
ap_setup_locked is named wps_ap_setup_locked in uci for consistency with other
wps related uci options.
Signed-off-by: Steven Honson <steven@honson.id.au>
The author of the upstream mwlwifi edited the history of the previous commit.
This commit not only fixes the updated hash but also sends in the latest
commits he made to the code which are mainly testing.
Signed-off-by: Gabe Rodriguez <lifehacksback@gmail.com>
Clarify opkg's messages related to downloads:
* more visible error message for package list download failure
* separate error message for signature file download error
* if wget returns 4, signal the network error more clearly
* remove '.' from end of filenames and URLs
* try signature check only if the package list was downloaded ok.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The radio would stop communicating completely. This issue was easiest to
trigger on AR913x devices, e.g. the TP-Link TL-WR1043ND, but other
hardware was occasionally affected as well.
The most critical issue was a race condition in disabling/enabling IRQs
between the IRQ handler and the IRQ processing tasklet
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All SPL variants are lzo compressed. The lzop binary is used for
compression but is not available in tools.
Additionally at least the NAND SPL support is broken and doesn't create
working bootloaders.
The fb3370 SPI NOR SPL enabled u-boot isn't required for LEDE since the
LEDE images are targeting the pre-installed EVA bootloader.
Mark these u-boot variants as well as the SPL variants for the
reference boards as broken till the lzma issues are fixed upstream and
we can use lzma instead of lzo compression.
Signed-off-by: Mathias Kresin <dev@kresin.me>
If only a single opkg control file exists (which can happen with
CONFIG_CLEAN_IPKG), grep would not print the file name by default. Instead
of forcing it using -H, we just switch to -l (print only file names) and
get rid of the cut.
Add -s to suppress an error message when no control files exist.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
There was a bug in brcmfmac patch that could result in treating random
memory as source of country codes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit c296ba834d.
According to several reports, the issues with the airtime fairness
changes are gone in current versions.
It's time to re-apply the patch now.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
accessing the u-boot's envs on this device is required to read the mac address.
These are the envs of the new u-boot, not of the stock one.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Instead of referencing u-boot packages from device profiles and having a
-all metapackage, make the u-boot packages hidden (they don't install to
bin/ anyway), and name the files in KERNEL_BUILD_DIR appropriately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
this commit allows to make a standalone u-boot for nsa310b.
While both first-stage and second-stage u-boot work fine if
installed to flash or loaded with kwboot,
I could not get stock u-boot nor bodhi's u-boot to chainload
any second stage u-boot (I also tried with dockstar's uboot
that works fine on this device if loaded with kwboot).
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
The subtarget on which the driver still depends was removed with
dee8986b95 because it was unmaintained
for a long time.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The hostapd_append_wpa_key_mgmt() procedure uses the possibly uninitialized
$ieee80211r and $ieee80211w variables in a numerical comparisation, leading
to stray "netifd: radio0 (0000): sh: out of range" errors in logread when
WPA-PSK security is enabled.
Ensure that those variables are substituted with a default value in order to
avoid emitting this (harmless) shell error.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The libtool target package stages its files into the host staging directory
and moves the libltdl library parts from there into the target staging
directory afterwards.
By doing so, the package essentially renders the host libtool infrastructure
unusable, leading to the below error in subsequent package builds:
libtoolize: $pkgltdldir is not a directory: `.../hostpkg/share/libtool`
Prevent this problem by using a dedicated libltdl install prefix in order to
avoid overwriting and moving away preexisting files belonging to tools/libtool.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add PROVIDES:=openvpn to the default recipe in order to let all build variants
provide a virtual openvpn package.
The advantage of this approach is that downstream packages can depend on just
"openvpn" without having to require a specific flavor.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The last two parameters passed between user space tc and kernel space
sched-cake were transposed due to a merge mistake in a parameter header
file.
As such, using a packet overhead figure was likely to set cake to wash
packet DSCP values. Similarly, the DSCP wash flag was used as an offset
to the displayed packet overhead value.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
- Adds support for passing file descriptors in ubus invoke requests
- Fixes clearing pending timers on ubus_shutdown()
- Fixes checking the amount of written data in ubusd
- Fixes an ubusd crash when trying to subscribe to system objects
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Changes the platform to use the Chipidea driver instead of the
generic USB host driver which has support for both host and
device modes (selected on boot).
The changes in 930-chipidea-pullup.patch are already in mainline.
I'll upstream 920-usb-chipidea-AR933x-platform-support.patch once I
can test the changes with a newer kernel.
Signed-off-by: Svetoslav Neykov <svetoslav@neykov.name>
Commit 131db36 "build: remove separate /install step for host builds" dropped
the package/*/host/install targets in favor to performing the install steps
within the compile target instead.
Adjust package/Makefile accordingly in order to prevent a missing
staging_dir/host/bin/opkg when staging package archives into the rootfs.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is used to save space on buildbot instances.
If any part of a package needs to be rebuild, the whole package is
rebuilt from scratch. Stamp files are preserved to allow dependency
checks to work
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update to 1.2.11 as suggested by upstream
Also add SF as primary source and main site as fallback
Note: SF doesn't carry the 1.2.11 update yet.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Knowing the package architecture at runtime can be useful, e.g. to
configure opkg repository URLs. The value of ARCH_PACKAGES ("%A" in
VERSION_SED) as added to openwrt_release (as DISTRIB_ARCH) and os-release
(as LEDE_ARCH).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Currently system log is always included as a part of ubox. Add logd as a
seperate package and add it to default packages list.
Signed-off-by: Andrej Vlasic <andrej.vlasic@sartura.hr>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
opkg doesn't have BUILD_VARIANTs anymore, so the previously defined
PKG_BUILD_DIR would lead to a weird 'opkg-' path component.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This allows some basic region switching on Netgear R8000. More devices &
codes may be added. Ideally it should be converted into DT info & patch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This makes use of cfg80211 feature backported & described in
188626f17c ("mac80211: backport cfg80211 support for
ieee80211-freq-limit DT property").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes build failure for kmod-can-c-can-platform which depends on
kmod-regmap for kernel 4.1 and 4.4.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch updates the QCA988X firmware to the latest revision
firmware-5.bin_10.2.4-1.0-00016
found in the official ath10k-firmware repository.
Tested on TP-Link Archer C7 v2.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Host files installed in Build/InstallDev are target-specific and will stay
in $(STAGING_DIR)/host after the STAGING_DIR_HOSTPKG unification.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Packets which are merely forwarded by the router and which are neither
involved in any DNAT/SNAT nor originate locally, are considered INVALID
from a conntrack point of view, causing them to get dropped in the
zone_*_dest_ACCEPT chains, since those only allow stream with state NEW
or UNTRACKED.
Remove the ctstate restriction on dest accept chains to properly pass-
through unrelated 3rd party traffic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Use ubus process signalling instead of 'kill pidof dnsmasq' for
SIGHUP signalling to dnsmasq when ntp says time is valid.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Most mac80211 drivers leave the SMPS field in the HT capabilities
uninitialized (unfortunately defaults to static SMPS), which leads to
some devices limiting themselves to single-stream rates in some modes
(mostly mesh and IBSS).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For 988X, 9980, 9984 CT firmware.
This should allow IBSS + RSN on at least the 988X firmware,
and includes recent stability fixes for all firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This at least makes it harder to hit some txq related
crashes on firmware restart, a potential memory leak,
and some other fixes.
Signed-off-by: Ben Greear <greearb@candelatech.com>
