On some devices the flash chip needs to be in 3-byte addressing mode during
reboot, otherwise the boot loader will fail to start.
This mode however does not allow regular reads/writes onto the upper 16M
half. W25Q256 has separate read commands for reading from >16M, however
it does not have any separate write commands.
This patch changes the code to leave the chip in 3-byte mode most of the
time and only switch during erase/write cycles that go to >16M
addresses.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Serial output was broken since 3.16 for shared uarts between
kernel and login. Fix this by adding a fix sent upstream.
While at it, drop a useless patch that adds duplicate code.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The NXP LSDK kernel backported changes for interface ndo_get_stats64
functions from mainline, this causes a compile error with
backports/mac80211, which expects the original 4.9 defintion.
As reversing the ndo_get_stats64 change signifcantly reduces the size of
patch 601, the patches that were aggregated into it have been
disaggregated.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
These conflict with the kmod packages (such as nf-netlink)
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Add same changes for arm8_32b subtarget and refresh config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mark target arc770 as source-only as it has package compile issues
(e.g. iproute2) due to the usage of uClibc.
As a prerequisite to be included in future releases the arc770 target
needs to switch either to glibc or musl.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Remove the ephy-pins from the ethernet device tree node. The ephy-pins
are useed to controll the ePHY LEDs and this board doesn't have these.
Instead one of the ePHY pins is used in GPIO mode to control the WAN
LED.
Use the switch LED trigger to control the WAN LED. Move the power LED
handling to diag.sh to show the boot status via this LED.
Add the missing kernel packages for USB and microSD card reader to the
default package selection.
Fix the maximum image size value. The board has a 32MByte flash chip.
Fixes: FS#1055
Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
[make the commit message more verbose, remove GPIO pinmux for pins not
used as GPIOs]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Without this, posix_[fm]advise does not work. This causes issues with
btrfs-progs, which uses fadvise to drop caches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This commit fix 5GHz wireless interface used in Archer C58/C59/C60v1
and set correctly MAC address on this interface.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
IMG_PREFIX can be modified in ImageBuilder by passing EXTRA_IMAGE_NAME
on command line, but Image/Prepare is not run in ImageBuilder. This
causes missing files when IMG_PREFIX is used for target file names in
Image/Prepare, then as source file names in Image/BuildKernel or
Image/Build.
Fix this by using a fixed output file name in Image/Prepare, and copy to
the expected file name in Image/BuildKernel instead, which is run by
ImageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Remove reference to pinmux group "wdt rst" on EW1200, ZBT-WG2626 and
ZBT-WG3526 devices. "wdt rst" is a pinmux function and not a pinmux
group.
Fixes the following error message during boot:
rt2880-pinmux pinctrl: invalid group "wdt rst" for function "gpio"
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Zyxel NBG6817 features a WiFi button, which becomes functional by setting
correct GPIO. It is a switch-type button, so it emits KEY_RFKILL on each ON
and OFF state. This is achieved by setting input-type to EV_SW.
Signed-off-by: Tolga Cakir <tolga@cevel.net>
Add the respective colour to the LED's names for the GL-AR150 to be conform
to the kernel. Also add netdev triggers for the LAN and WAN LED.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Append and enforce image metadata. Remove the device specific image
checks, they are replaced by image metadata.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.
Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.
Signed-off-by: Mathias Kresin <dev@kresin.me>
initramfs is not the proper name for this, as it stores a boot ramdisk
and not a filesystem. Update the name to reflect it's usage correctly.
If CMDLINE_OVERRIDE is enabled, the chosen bootargs aren't used at all.
Drop them from the device tree source file to not cause confusion.
Remove the noinitrd bootarg. Due to the empty ramdisk this parameter
isn't required any longer:
[ 0.000000] Initrd not found or empty - disabling initrd
Use the LEDE mtd-mac-address* device tree properties to set the interfaces
MAC-Addresses.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the kernel config changes added with the HiveAP 330 to the
subtarget the board belongs to instead of changing the target kernel
config.
While at it, move the TL_WDR4900_V1 config symbol to the containing
subtarget and disable boards we don't support.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following moves the mpc85xx target (generic & P1020) to the new
build code style.
Compile & Flash tested on an Aerohive HiveAP-330.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
That device does not have a USB port. It as the same board as the
WT3020-8M, but without soldered USB port port. Also the case lacks the
opening for the port.
Reported-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Mathias Kresin <dev@kresin.me>
the nexx wt3020-8M has a usb 2.0 port,
add usb 2.0 support packages to its default package list.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This change makes it possible to configure the wan/dsl ppp interface
settings independantly from the used TC-Layer (ATM/PTM).
By using dsl0 as interface name as for the xrx200 we can get rid of a
few conditionals which were introduced because of the different default
TC-Layer in xway and xrx200.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set a default Annex matching the the annex of the selected adsl
firmware.
Set Annex B for xrx200 board which are known to have an ADSL hybrid for
Annex B.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With removing the boards from the the default case to fix the xDSL WAN
MAC-Address, the setting for the default LAN interface wasn't added.
Fixes: 92a12c434c ("lantiq: fix avm fritz box mac addresses")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Patch 610-netfilter_match_bypass_default_check added an extra flag IPT_F_NO_DEF_MATCH
which is copied to user space in function copy_entries_to_user. The 32bit compat
layer function was missing the same logic to copy the flag IPT_F_NO_DEF_MATCH to
user space for a 64bit kernel and 32 bit user space.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Thierry Dutre <thierry.dutre@dtsystems.be>
Patch 610-netfilter_match_bypass_default_check added an extra flag IPT_F_NO_DEF_MATCH
which is copied to user space in function copy_entries_to_user. The 32bit compat
layer function was missing the same logic to copy the flag IPT_F_NO_DEF_MATCH to
user space for a 64bit kernel and 32 bit user space.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Thierry Dutre <thierry.dutre@dtsystems.be>
Patch 610-netfilter_match_bypass_default_check added an extra flag IPT_F_NO_DEF_MATCH
which is copied to user space in function copy_entries_to_user. The 32bit compat
layer function was missing the same logic to copy the flag IPT_F_NO_DEF_MATCH to
user space for a 64bit kernel and 32 bit user space.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Thierry Dutre <thierry.dutre@dtsystems.be>
On RB91x (and possibly others), there is a small SPI flash to store boot
loader and configuration. It needs 4K sectors to be able to write the
configuration using rbcfg
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In 4.9, gpio count is rounded up to 32 due to the use of bgpio in the
ath79 gpio controller driver.
Fix base values in mach files to account for that
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Change the Makefile to use LTO for better code optimisations. Gains are
very low, only 270 bytes saved, but it's only Makefile changes.
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
Some bootloaders set a cache cohenrency to a very slow mode. Use code from
Linux kernel to set it to "Cacheable, noncoherent, write-back, write
allocate".
Perfomance impact is significant on TP-Link EAP245 board, kernel
decompression time fall from 33 seconds to less than 1.
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
The Raspberry Pi bootloader reads configuration values from config.txt
in the boot partition. This file allows to specify the amount of memory
to assign to the GPU, the license keys for hardware MPEG-2 and VC-1
decoding, Device Tree parameters and overlays, and lots of other things.
Since sysupgrade only restores the configuration after booting the newly
flashed image, these values will not be active, even if sysupgrade would
save /boot/config.txt. To solve this, add the file to the files to be
backed up, and restore it in platform_copy_config, before reboot.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This affects the following boards:
* dr344
* archer-c58-v1
* archer-c60-v1
* tl-wr902ac-v1
* tl-wr942n-v1
* ubnt-uap-pro
* ubnt-unifi-outdoor-plus
The build fails for any of these boards because the resulting kernel
image will not fit into the kernel partition.
When CONFIG_KERNEL_KALLSYMS is not set it could be that the kernel will
fit onto the board again, this is the case for release images.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kernel 4.9 support was added about 2 weeks ago and we haven't seen any
major regression so far. This patch was not ported to kernel 4.9, this
needs some additional work:
821-serial-core-add-support-for-boot-console-with-arbitr.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When the kmod-at91-adc package is activated for the at91 target the new
option CONFIG_AT91_SAMA5D2_ADC is selectable and not handled. Add this
option to the kernel 4.9 configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9561+QCA9888.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f040000 +$filesize
3. cp.b $fileaddr 0x9f040000 $filesize
4. reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
