Use the DMI data available in sysfs to extract manufacturer and model info
and write it to /tmp/sysinfo/.
The data will be picked up by board_detect and can be used by e.g. LuCI to
display a more appropriate model description.
On an APU board the files will contain the following values:
# cat /tmp/sysinfo/model
PC Engines APU
# cat /tmp/sysinfo/board_name
pc-engines-apu
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Enable support for DMI decoding in the kernel so that we can access
manufacturer and model information via sysfs.
Also remove redundant per-subtarget DMI overrides and preset a few
previously unset symbols popping up due to the now enabled DMI support.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
most symbols should be in Kernel packages
depending on HW the removal of
CONFIG_REALTEK_PHY
and USB symbols might be wrong
compile tested only
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
uClibc-ng pretends to be GNU libc 2.2 and then a fallback
scanf check is tried, so that libmount is disabled
afterwards. Add a fix already suggested upstream.
Add librt dependency required for other apps, too.
Signed-off-by: Waldemar Brodkorb <wbx@uclibc-ng.org>
Initially for ARC we were building vmlinux images because it
was both simpler and more convenient to debug Linux kernel
in runt-time via JTAG. Now when base system works quite nice
we may finally use U-Boot for loading the system image as
well. Still we keep building vmlinux images as some of our
boards are development boards and loading images with JTAG
could be at some points very beneficial.
Note for U-Boot header it's required to specify 2 values:
* loading address
* entry point (if it doesn't match loading address)
and in case of ARC entry point (EP) not only differs from
loading address but also changes from build to build due to
initramfs being placed between loading address and text section.
To accommodate that feature we have to calculate EP after
vmlinux gets built and before call to mkimage.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
even it's a little bit verbose, unmacrod board descriptions are much
easier to read and to understand.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
It turns out most device vendors don't set the correct country code
in their devices' on-flash-EEPROM sections as they apparently rather
provide a complete per-target-market firmware with patched drivers
instead of just setting the country code.
This results in the driver to incorrectly assume the value stored in
the on-flash-EERPOM (usually US or China) being the regulatory domain
inside which the device is being used.
To work around this issue, OpenWrt introduced the ATH_USER_REGD config
variable to decide during build whether or not to allow the user to
override the regulatory domain setting. This option, however, is not
enabled by default and thus ends up being disabled for snapshots builds
and released binaries.
As we know for a long time that most devices got borked regulatory
domain values set in their EEPROMs we should allow our users to respect
their local law (instead of just assume US or China laws).
Note that also the current default has great potential of users not
ever setting their regulatory domain and thus using inapproriate and
potentially illegal frequencies and/or tx-power settings
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows one to select CT firmware for ath10k
if one prefers to try this firmware instead of stock
ath10k firmware.
The 10.1 (988X) firmware can actually be installed beside the
default firmware, but it will not be used as long as the firmware-5.bin
file exists. Users could rename the files and reboot to use different
images.
The 99X0 (wave-2) firmware uses the same firmware-5.bin name as default
firmware, so it cannot be installed at the same time as default firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This patch adds support for the Netgear EVG2000 VoIP Gateway to the
bcm63xx targets.
This device was not sold to the general public, but rather is/was
provided by telcos to customers in Sweden, Australia, Singapore and
other parts of asia.
Known issues:
- Unable to detect 53115 switch. This appear to be a problem with
probing for the PHY using MDIO and results in error 5. Doesn't seem to
be a problem with the configuration, and could use someone with
experience to have a look at it.
- Uses the b43 driver as using the OpenWRT/LEDE broadcom-wl driver
fails to load the firmware for the 4322, so 802.11n is not supported.
More info on the device and the research can be found at:
https://wiki.openwrt.org/toh/netgear/evg2000https://wikidevi.com/wiki/Netgear_EVG2000https://github.com/Xotic750/mirror-lede/tree/evg2000https://forum.openwrt.org/viewtopic.php?id=63950
Signed-off-by: Graham Fairweather <xotic750@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some devices with ath9k WiFi require changing the default active low
polarity to high in order to correctly operate the WiFi status LEDs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These scripts were causing ip issues in the latest version of LEDE:
https://gist.github.com/Noltari/6d20d8bcbe236caf516c0a73f5477d00
Fixes preinit iface script by making eth0 the default ifname and only changing
it to eth1 for the devices that specifically need it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Kernel module for the OMAP Random Number Generator
found on OMAP16xx, OMAP2/3/4/5 and AM33xx/AM43xx
multimedia processors.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Some Git versions have issues following the HTTP->HTTPS redirect and since
the keyring package is fetched from this host, switching to HTTPS is a
sensible choice anyway.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
