Adds preliminary kernel 4.9 support for this target.
- Refreshed/Updated all patches
Added 3 new patches:
- 093 --> Add virtual PCI MMIO mapping
- 230 --> Remove deprecated code
- 240 --> Rework AT24 eeprom code to use the new NVMEM API
Compiled & tested on cns3xxx (gw2388)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Add support for the Observa Telecom VH4032N router.
This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB
host ports.
The wifi chip is an onboard Broadcom BCM43222.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: use gpio-hog instead of abusing ephy-reset]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Remove CONFIG_VLAN_8021Q overrides for two targets
These features are built into the kernel image for all targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Probe the switch through DT instead of a platform device. This fixes
probe, as GPIO offsets are now properly accounted for.
Fixes the following issue:
[ 0.802953] 8021q: 802.1Q VLAN Support v1.8
[ 0.810518] rtl8366_smi: gpio_request failed for 18, err=-517
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
BCM6362 and BCM3380 seem to share the same PRID. Disable serial output
for them until we can find a way to tell them apart reliably.
Fixes: 8f3cfe4ba2 ("brcm63xx: lzma-loader: add BCM3380 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This patch adds support for the ADB P.DG AV4202N aka Pirelli PRG AV4202N.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for mapping some GPIO lines to IRQs. GPIO to IRQ mappings
were found out through experimentation, helped by having the GPIO as
output still toggling the IRQ input.
Based-on: http://patchwork.ozlabs.org/patch/660534/
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Setting the clear bit for an interrupt seems to cause interrupts to be
deasserted again immediately. So unset the bit for BCM6318 to allow
subsequent interrupts to still work.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Default CONSOLE value for ar71xx target is "ttyS0,115200", so there
is no need to specify the same value in device profiles.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit reverts 42f3c1f ("arc770: fix broken upstream change")
and simultaneously adds back-ported fix from Linus' tree:
a524c218bc94 ("ARC: [arcompact] brown paper bag bug in unaligned
access delay slot fixup").
Note mentioned patch will appear in stable trees soon as well so
IMHO there's not much sense in adding this separate patch in lede/master branch.
As well as we will get rid of it here in 17.01 once we bump 4.4 kernel here
later down the line.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Jo-Philipp Wich <jo@mein.io>
mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.
Signed-off-by: Claudio Leite <leitec@gmail.com>
buildbot fails to build without regmap, which I couldn't reproduce locally.
Hopefully this fixes it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
64 bit support for Raspberry Pi 3 is experimental. However, bcm2709 subtarget
should serve as a stable and compatible 32 bit support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds support for Raspberry Pi 3 on the bcm2709 subtarget, in order to
keep 32 bit image support when 64 bit support is added on bcm2710 subtarget.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Initial idea was to use package with this PHY driver for devices that
need it. Unfortunately this can't work as bgmac is built-in and PHY
probing happens before loading modules - it results in PHY subsystem
picking default (generic) PHY driver.
There were two ways of solving this:
1) Making bcm53xx use bgmac as module
xor
2) Built-in Broadcom PHY driver
After some quick discussion it seems we can simply built-in the driver
as increased kenel size is relatively small (1805 B).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
These are patches queued for 4.11. It adds support for even more hw and
removes some annoying WARN_ONCE.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's needed for macaddr_add.
Fixes: 50efd403e6 ("bcm53xx: set WAN MAC address to don't share one with LAN interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.
Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It just makes code consistent. This trivial change may be a 17.01
candidate to provide simpler backporting experience.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In kernel 4.9 it's already present so we don't want to overwite it (with
older & API incompatible version).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked
broken, except arc770 and arch38 due to broken toolchain.
Runtime-tested on ar71xx, octeon, ramips and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.
Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.
The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).
If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
