Commit graph

2881 commits

Author SHA1 Message Date
John Crispin
1cdd3403ba ar71xx: WNR1000v2: fix for random WLAN MAC
Fix for invalid/random WLAN MAC address in WNR1000v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3
and WNR612v2.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49051
2016-03-20 14:41:58 +00:00
Hauke Mehrtens
fcbc97ad78 kernel: update kernel 4.1 to version 4.1.20
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49035
2016-03-18 23:41:21 +00:00
John Crispin
4d6c4994fc ar71xx: Use PHY fixups for Open Mesh MR1750
The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.

This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.

Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49031
2016-03-16 09:27:14 +00:00
John Crispin
ebcce35be4 ar71xx: Use PHY fixups for Open Mesh MR900
The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.

This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.

Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49030
2016-03-16 09:27:11 +00:00
John Crispin
22c5f96c6b ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x
Some u-boot versions for QCA955x change the delays based on the link speed
during boot. This usually breaks the support of other linkspeeds when
OpenWrt is booted. It also conflicts with the
at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own
values in QCA955X_GMAC_REG_ETH_CFG.

The default RGMII values from the Atheros u-boot are currently used to
preset the existing mach files. These may have to be adjusted for boards
using different values but which are not currently set them explicitely in
OpenWrt.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Christian Beier <cb@shoutrlabs.com>
Cc: Chris R Blake <chrisrblake93@gmail.com>
Cc: Benjamin Berg <benjamin@sipsolutions.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Dirk Neukirchen <dirkneukirchen@web.de>
Cc: Christian Mehlis <christian@m3hlis.de>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 49029
2016-03-16 09:27:08 +00:00
John Crispin
be68f34708 ar71xx: Clear bits in ath79_setup_qca955x_eth_cfg
Some u-boot versions for QCA955x set currently not cleared bits depending
on the used link speed. This breaks the rx/tx under OpenWrt. The mach-*.c
file is responsible to select the correct configuration bits and thus the
ath79_setup_qca955x_eth_cfg has to clear the unset.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49028
2016-03-16 09:27:04 +00:00
John Crispin
eff9a4b176 ar71xx: Extend the list of bits in QCA955X_GMAC_REG_ETH_CFG
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49027
2016-03-16 09:27:01 +00:00
John Crispin
3fd98db818 ar71xx: Add support for the OMYlink OMY-X1
This patch adds support for the OMYlink OMY-X1

https://wiki.openwrt.org/toh/omylink/omy-x1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49026
2016-03-16 09:26:58 +00:00
John Crispin
05d73a2a73 ar71xx: Arduino Yun board 'WLAN RST' button support
This patch adds support for Arduino Yun board "WLAN RST" button.

Signed-off-by: Hirokazu MORIKAWA <morikw2@gmail.com>

SVN-Revision: 48983
2016-03-10 19:11:13 +00:00
John Crispin
346b1905fb ar71xx: add support for the Telldus TellStick ZNet Lite
Signed-off-by: Micke Prag <micke.prag@telldus.se>

SVN-Revision: 48977
2016-03-10 19:07:26 +00:00
Felix Fietkau
4802f611cb ar71xx: fix qca956x ethernet initialization
Complete internal switch initialization for QCA956X.
Set default mdio device if the interface mode of GE0 is not SGMII (fix ticket #21520).

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 48937
2016-03-07 08:45:01 +00:00
Felix Fietkau
c865ae03f6 ar71xx: enable USB packages for WNR2200 (fixes #21984)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48936
2016-03-06 19:40:31 +00:00
Hauke Mehrtens
e9d7ee4f41 kernel: update kernel 4.4 to version 4.4.4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48933
2016-03-05 17:51:37 +00:00
Felix Fietkau
3f971c0dc8 ar71xx: WNR612v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48924
2016-03-05 09:45:15 +00:00
Felix Fietkau
94b8a6b5cf ar71xx: WNR2000v3: add speed_mask to Ethernet port LED initialization
This patch add speed_mask parameter to Ethernet port LED initialization
during system startup. LEDs are configured to show amber light for 10 Mbps
link and green for 100 Mbps as described on device label.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48923
2016-03-05 09:45:10 +00:00
Felix Fietkau
53b3872ddf ar71xx: WNR2000v3: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48922
2016-03-05 09:45:06 +00:00
Felix Fietkau
6bece706ec mac80211: ath9k: enable GPIO buttons
Enable platform-defined GPIO button support for ath9k device.
Key poller is activated for attached platform buttons.
Requires ath9k GPIO chip access.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48921
2016-03-05 09:45:03 +00:00
John Crispin
fbb2449953 AP121 target: fix board detection in ar71xx.sh
Signed-off-by: Attila Lendvai <attila@lendvai.name>

SVN-Revision: 48916
2016-03-04 08:33:38 +00:00
Felix Fietkau
a8c15c0204 mac80211: ath9k: enable platform WLAN LED name
Enable platform-supplied WLAN LED name for ath9k device.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 48879
2016-03-02 13:22:40 +00:00
John Crispin
7d008e8bf0 ar71xx: Add OOLITE to the Gainstrong profile, removed standalone profile.
This patch moves the OOLITE profile code into the overarching Gainstrong
profile and deletes the old single profile file.

Signed-off by: Stijn Segers <francesco.borromini@inventati.org>

SVN-Revision: 48866
2016-03-01 09:17:09 +00:00
Felix Fietkau
619a58d641 ar71xx, firmware-utils: split ubdev01 flash layout from XM
The ubdev01 profile defines its own MTDPARTS with smaller firmware
partition, so give it its own UBNT_BOARD in mkfwimage.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 48828
2016-02-29 20:11:30 +00:00
Felix Fietkau
ce9dc109a4 Revert "ar71xx: WNR612v2: exclude USB modules from image"
This reverts commit r48778. The issue has now been fixed properly

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48808
2016-02-26 20:47:13 +00:00
John Crispin
ae27fab5cf ar71xx: Renamed Gainstrong MiniBox profile to Gainstrong (manufacturer) and updated copyright
This is the first patch of a series of three to tidy up the profiles for
Gainstrong devices. Right now there are two Gainstrong profiles, each
for a single device built by this manufacturer. This patch renames the
MiniBox profile to Gainstrong and updates the copyright notice.

The series applies cleanly to current trunk. Resent with the architecture in
the subject, forgot that the first time.

Signed-off by: Stijn Segers <francesco.borromini@inventati.org>

SVN-Revision: 48797
2016-02-26 08:35:38 +00:00
Hauke Mehrtens
cb04b8d582 kernel: update kernel 4.4 to version 4.4.3
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48783
2016-02-25 21:54:39 +00:00
Felix Fietkau
5be9e97a82 ar71xx: WNR612v2: fix for random WLAN MAC
Fix for invalid/random WLAN MAC address in WNR612v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48779
2016-02-25 13:31:38 +00:00
Felix Fietkau
e0d358c436 ar71xx: WNR612v2: exclude USB modules from image
Netgear WNR612v2 has no USB port yet default system image
includes USB kernel modules. This patch fixes that.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48778
2016-02-25 13:31:35 +00:00
Felix Fietkau
3964ac919a ar71xx: WNR2000v3: fix for random WLAN MAC
Fix for invalid/random WLAN MAC address in WNR2000v3. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48777
2016-02-25 13:31:32 +00:00
John Crispin
56714adb4b ar71xx: correct imagename for TPlink WA730RE
- insert missing "-" to separate model and version

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>

SVN-Revision: 48769
2016-02-25 10:14:13 +00:00
John Crispin
2a58dbda98 ar71xx: correct imagename for TPlink WA701ND
- it seems there was never a 701N-model build

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>

SVN-Revision: 48768
2016-02-25 10:14:11 +00:00
John Crispin
bf49188bb1 ar71xx: matchup of TPlink WR841N(D)-names
- remove the suffix (N, ND) to indicate that the image is for all
  WR841-models
- some of these models have a "N"-suffix, others have (ND)-suffix,
  but the boards are the same - only difference is the detachable
  antenna on "D"-models
- discussed this idea to remove the suffix in IRC with jow and Borromini

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>

SVN-Revision: 48767
2016-02-25 10:14:08 +00:00
Felix Fietkau
29bbc6e6be ar71xx: reset ethernet tx ring on fast reset to prevent packet loss / irq issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48753
2016-02-22 15:11:23 +00:00
Jo-Philipp Wich
c834c83f0f ar71xx: add missing symbol to Linux 4.4 config (#21878)
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 48742
2016-02-18 12:09:34 +00:00
Jo-Philipp Wich
473e9cad43 ar71xx: add missing kernel symbol (#21849)
Also reorder subtarget kernel configs.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 48717
2016-02-12 19:55:07 +00:00
John Crispin
cede06cebc ar71xx: Support for Ubiquiti UniFi AP AC LITE
Add support for the Ubiquiti UniFi AP AC LITE
Signed-off-by: P.Wassi <p.wassi at gmx.at>

SVN-Revision: 48711
2016-02-12 08:31:32 +00:00
John Crispin
13a85914ae ar71xx: Make code formatting consistent on ath79/machtypes.h
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 48706
2016-02-12 08:30:38 +00:00
John Crispin
d6cb792d21 ar71xx: Added support for TL-WA801NDv3
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 48705
2016-02-12 08:30:28 +00:00
John Crispin
9cf8461394 ar71xx: WNR2000v3: exclude USB modules from image
Netgear WNR2000v3 has no USB port yet default system image
includes USB kernel modules. This patch fixes that.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48701
2016-02-12 08:29:54 +00:00
Felix Fietkau
376e3ade79 ag71xx: fix build error with debugfs code
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48695
2016-02-11 22:48:36 +00:00
Felix Fietkau
37dd95b772 ag71xx: increase rx ring size to improve performance
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48694
2016-02-11 15:02:07 +00:00
Felix Fietkau
11ca71cfdb ag71xx: store ring size order instead of ring size to avoid div/mod
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48693
2016-02-11 15:02:00 +00:00
Felix Fietkau
033fbb7778 ag71xx: increase tx ring size to improve performance
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48692
2016-02-11 15:01:54 +00:00
Felix Fietkau
b7a2c533da ag71xx: optimize icache footprint of the receive poll function
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48691
2016-02-11 15:01:48 +00:00
Felix Fietkau
b1431170ee ar71xx: register only the built-in switch MDIO bus, hook up eth0 to it, should hopefully fix regression reported in #21520
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48652
2016-02-07 21:00:11 +00:00
Felix Fietkau
a63fd6faf7 ar71xx: fix MDIO bus probe on QCA956x
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48651
2016-02-07 21:00:01 +00:00
Felix Fietkau
a5dd378a0e ar71xx: fold patch 622-MIPS-ath79-add-support-for-QCA956x-ethernet.patch into files/
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48650
2016-02-07 20:59:51 +00:00
Felix Fietkau
411515b368 ar71xx/image: use SOURCE_DATE_EPOCH for mksquashfs-lzma
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 48589
2016-01-31 23:29:41 +00:00
Felix Fietkau
2067f7f1de ar71xx: use page fragment API in the ethernet driver
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48578
2016-01-31 12:29:34 +00:00
Felix Fietkau
2530640f07 ar71xx: add support for linux 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48563
2016-01-30 13:19:53 +00:00
Felix Fietkau
e5b5cce442 ar71xx: fix a few include errors
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48562
2016-01-30 13:19:37 +00:00
Hauke Mehrtens
4807ca67d6 kernel: update kernel 4.1 to version 4.1.16
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48497
2016-01-25 21:44:12 +00:00