Commit graph

596 commits

Author SHA1 Message Date
John Crispin
6090ddc896 adds fon20n profile
SVN-Revision: 34112
2012-11-07 20:26:31 +00:00
John Crispin
3991526989 ramips: use kernel 3.6.6
## Booting image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.6.6
   Created:      2012-11-06  14:19:54 UTC

 System Control Status = 0x20440000
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3560768 Bytes =  3.4 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

[    0.000000] Linux version 3.6.6 (daniel@localhost.localdomain) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #2 Tue Nov 6 16:19:48 IST 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[    0.000000] Ralink RT3052 id:1 rev:2 running at 384.00 MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  console=ttyS1,57600n8 board=ALL0239-3G mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),6976k(rootfs),7872k@0x50000(firmware) rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Writing ErrCtl register=0000c388
[    0.000000] Readback ErrCtl register=0000c388
[    0.000000] Memory: 27048k/32768k available (2015k kernel code, 5720k reserved, 498k data, 2676k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] console [ttyS1] enabled, bootconsole disabled
[    0.000000] console [ttyS1] enabled, bootconsole disabled
[    0.010000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
[    0.090000] pid_max: default: 32768 minimum: 301
[    0.100000] Mount-cache hash table entries: 512
[    0.110000] NET: Registered protocol family 16
[    0.120000] MIPS: machine is Allnet ALL0239-3G
[    0.140000] bio: create slab <bio-0> at 0
[    0.150000] Switching to clocksource MIPS
[    0.160000] NET: Registered protocol family 2
[    0.170000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.180000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.200000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.210000] TCP: reno registered
[    0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.230000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.240000] NET: Registered protocol family 1
[    5.460000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.470000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.490000] msgmni has been set to 52
[    5.500000] io scheduler noop registered
[    5.510000] io scheduler deadline registered (default)
[    5.520000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    5.530000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
[    5.550000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    5.560000] physmap platform flash device: 00800000 at bf000000
[    5.580000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001000
[    5.600000] Amd/Fujitsu Extended Query Table at 0x0040
[    5.610000]   Amd/Fujitsu Extended Query version 1.3.
[    5.620000] number of CFI chips: 1
[    5.620000] 6 cmdlinepart partitions found on MTD device physmap-flash.0
[    5.640000] Creating 6 MTD partitions on "physmap-flash.0":
[    5.650000] 0x000000000000-0x000000030000 : "u-boot"
[    5.660000] 0x000000030000-0x000000040000 : "u-boot-env"
[    5.680000] 0x000000040000-0x000000050000 : "factory"
[    5.690000] 0x000000050000-0x000000130000 : "kernel"
[    5.700000] 0x000000130000-0x000000800000 : "rootfs"
[    5.710000] mtd: partition "rootfs" set to be root filesystem
[    5.730000] split_squashfs: error occured while reading from "physmap-flash.0"
[    5.740000] 0x000000050000-0x000000800000 : "firmware"
[    5.760000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 33, using 33
[    5.780000] TCP: cubic registered
[    5.780000] NET: Registered protocol family 17
[    5.790000] 8021q: 802.1Q VLAN Support v1.8
[    5.820000] Freeing unused kernel memory: 2676k freed
[    6.490000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -

Please press Enter to activate this console. [   10.150000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   10.170000] Backport based on wireless-testing.git master-2012-09-07
[   10.180000] compat.git: wireless-testing.git
[   10.210000] cfg80211: Calling CRDA to update world regulatory domain
[   10.230000] cfg80211: World regulatory domain updated:
[   10.240000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.250000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.270000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.280000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.300000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.310000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.430000] NET: Registered protocol family 10
[   10.760000] PPP generic driver version 2.4.2
[   10.820000] l2tp_core: L2TP core driver, V2.0
[   10.840000] l2tp_netlink: L2TP netlink interface
[   10.870000] sit: IPv6 over IPv4 tunneling driver
[   10.920000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.060000] NET: Registered protocol family 24
[   11.090000] nf_conntrack version 0.5.0 (464 buckets, 1856 max)
[   11.230000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   11.410000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.510000] device eth0.1 entered promiscuous mode
[   14.520000] device eth0 entered promiscuous mode
[   14.530000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   14.550000] br-lan: port 1(eth0.1) entered forwarding state
[   14.560000] br-lan: port 1(eth0.1) entered forwarding state
[   16.560000] br-lan: port 1(eth0.1) entered forwarding state
[   16.600000] ramips-wdt: timeout value 60 must be 0 < timeout <= 33, using 33

BusyBox v1.19.4 (2012-11-06 13:40:37 IST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Bleeding Edge, r34079)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------
root@OpenWrt:/#

SVN-Revision: 34111
2012-11-07 20:26:21 +00:00
John Crispin
480892226d ramips: add HAVE_CLK to Kconfig on all ramips socs
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 34110
2012-11-07 20:26:04 +00:00
John Crispin
feb31be6af ramips: add linux-3.6 configuration for ramips socs
Signed-off-by: Daniel Golle <dgolle@allnet.de>

 create mode 100644 target/linux/ramips/rt288x/config-3.6
 create mode 100644 target/linux/ramips/rt305x/config-3.6
 create mode 100644 target/linux/ramips/rt3883/config-3.6

SVN-Revision: 34109
2012-11-07 20:25:55 +00:00
John Crispin
ca1fcaed5b ramips: port patches to linux-3.6
Signed-off-by: Daniel Golle <dgolle@allnet.de>

 create mode 100644 target/linux/ramips/patches-3.6/001-mips-add-cp0-compare-irq-function.patch
 create mode 100644 target/linux/ramips/patches-3.6/010-mtd_fix_cfi_cmdset_0002_erase_status_check.patch
 create mode 100644 target/linux/ramips/patches-3.6/011-mtd-cfi_cmdset_0002-force-word-write.patch
 create mode 100644 target/linux/ramips/patches-3.6/100-mips-ralink-core.patch
 create mode 100644 target/linux/ramips/patches-3.6/101-rt288x_serial_driver_hack.patch
 create mode 100644 target/linux/ramips/patches-3.6/102-rt288x-pci-driver-hook.patch
 create mode 100644 target/linux/ramips/patches-3.6/103-ethernet.patch
 create mode 100644 target/linux/ramips/patches-3.6/104-ramips-watchdog-driver.patch
 create mode 100644 target/linux/ramips/patches-3.6/105-ramips-spi-driver.patch
 create mode 100644 target/linux/ramips/patches-3.6/105-usb_dwc_otg.patch
 create mode 100644 target/linux/ramips/patches-3.6/106-rt3883-pci-support.patch
 create mode 100644 target/linux/ramips/patches-3.6/200-rt3883-ehci-glue.patch
 create mode 100644 target/linux/ramips/patches-3.6/201-rt3883-ohci-glue.patch

SVN-Revision: 34108
2012-11-07 20:25:34 +00:00
Gabor Juhos
a0dd47bbed ramips: enable USB power on the DIR-645
Closes #12422.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34082
2012-11-05 11:04:45 +00:00
Gabor Juhos
829aaedcbf ramips: add restorefactory to default package set for ALL0239-3G and ALL0256N
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 34078
2012-11-05 06:58:53 +00:00
Gabor Juhos
e91dc2e5b3 target: refresh all target configs with kconfig.pl
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33987
2012-10-29 10:11:05 +00:00
Gabor Juhos
db5eea6acd ramips: use correct key code for the RFKILL switch on the TEW-691GR
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33943
2012-10-26 18:53:44 +00:00
Gabor Juhos
b530d9d2b3 ramips: disable 5GHz on the built in wireless mac of the TEW-69{1,2}GR
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33864
2012-10-19 17:42:22 +00:00
Gabor Juhos
6ca2970e4b ramips: add profile and build image for the TEW-691GR board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33852
2012-10-18 07:23:13 +00:00
Gabor Juhos
21180e29f7 ramips: add user-space support for TEW-691GR
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33851
2012-10-18 07:23:12 +00:00
Gabor Juhos
25d53c4c28 ramips: rt3883: add initial support for the TRENDnet TEW-691GR board
No wireless support.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33850
2012-10-18 07:23:11 +00:00
Gabor Juhos
462a53c367 ramips: add profile and build image for the TEW-692GR board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33849
2012-10-18 07:23:10 +00:00
Gabor Juhos
d3c368c324 ramips: add user-space support for the TEW-692GR board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33847
2012-10-18 07:23:07 +00:00
Gabor Juhos
7f8b7207c9 ramips: rt3883: add initial support for TRENDnet TEW-692GR board
No wireless support.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33846
2012-10-18 07:23:06 +00:00
Gabor Juhos
bf9ae9432b ramips: add profile and build image for the DIR-645 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33845
2012-10-18 07:23:04 +00:00
Gabor Juhos
06edafd079 ramips: add user space support for the DIR-645
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33844
2012-10-18 07:23:03 +00:00
Gabor Juhos
d1a253a2fd ramips: rt3883: add inital support for the DIR-645 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33843
2012-10-18 07:23:02 +00:00
Gabor Juhos
e962c16a88 ramips: use get_magic_long in sysupgrade image check
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33842
2012-10-18 07:23:00 +00:00
Gabor Juhos
d832cd11f8 ramips: add image for ALL0256N-8M
The new version of the ALL0256N now got 8MB SPI NOR flash instead of 4MB.
In order to expose the whole amount of flash, add another image which contains
the corresponding GENERIC_8M mtdparts.

[juhosg: change suffix from '8m' to '8M']

Patch by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33614
2012-10-04 06:34:09 +00:00
Gabor Juhos
e3bcbeb427 ramips: add memory detection code for RT5350
SVN-Revision: 33571
2012-09-27 10:18:15 +00:00
Gabor Juhos
80d2da9f0f ramips: allow to use custom code for memory size detection
SVN-Revision: 33570
2012-09-27 10:18:14 +00:00
John Crispin
d8c04821c3 make uci-defaults switch detection work on rt5350
SVN-Revision: 33549
2012-09-25 14:47:18 +00:00
John Crispin
34d57ebd8b add ethernet support for rt5350
SVN-Revision: 33548
2012-09-25 14:47:08 +00:00
John Crispin
af0cd76937 make ramips ethernet use a register mapping table
SVN-Revision: 33547
2012-09-25 14:46:58 +00:00
John Crispin
394a560a9a unbreak port mapping detection
SVN-Revision: 33536
2012-09-25 09:51:48 +00:00
John Crispin
223db72385 D-Link DAP-1350; Avoid bricking esw config
This is a patch to connect eth0.1 (lan) to the only
ethernet connector available.

D-Link DAP-1350 goes bricked with AA 12.09-beta.

This is because the current esw configuration for the
board connects eth0.2 (wan) to the *ONE and ONLY*
ethernet connector available, preventing initial access
to the board through 192.168.1.1 on eth0.1 after flashing,
effectively bricking the board.

There are things that should be done to make this board
really useful, but for AA 12.09, this one liner is
indispensable.

Signed of by Yoichi Shinoda <shinoda@jaist.ac.jp>

SVN-Revision: 33411
2012-09-15 09:28:28 +00:00
John Crispin
bf355f8ee9 ramips/rt3883: fix a typo in the ASUS profile
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33410
2012-09-15 09:20:50 +00:00
Gabor Juhos
0a42b02126 ramips/rt305x: add initial support for Rt5350 SoC
Somehow detecting the RAM size in common/setup.c doesn't
work here, it always detects 64M and then crashes on devices
with less RAM.
Probably using MEMC_REG_SDRAM_CFG1 to know the RAM size is how
it could be, for now I use the mem=32M kernel parameter to get
stuff working.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33381
2012-09-12 19:03:12 +00:00
Gabor Juhos
d8b2fef763 ramips: Add missing andmask to ramips_esw register read for recv_good value.
Add missing andmask to ramips_esw register read for recv_good value.

Without the mask, recv_bad leaks into the recv_good packet count.
Didn't notice the bug before since you don't usually get bad
packets, so I only saw it when I was playing with overlength packets
earlier...

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 33322
2012-09-05 20:08:43 +00:00
Gabor Juhos
04c6143ca9 ramips: Use doubletagging to disable ramips_esw vlan by default, it seems more reliable.
Use doubletagging to disable ramips_esw vlan by default, it seems
more reliable.

Daniel Golle found an issue where sometimes (possibly only for
RT3352) the default vlan disable method (clearing en_vlan, untag,
doubletag and putting all ports into vlan 0) doesn't work and the
packets get sent out vlan-tagged with vlan 0.

Instead switch to using the doubletagging method (allow doubletagged
packets, put all ports into vlan 0 with untag enabled) by default.

Unless someone figures out a way to really globally disable vlan for
this switch, this seems like the best (most reliable) option.

I did some tests regarding maximum packet size and did not see any

difference between the two methods, both allow for slightly bigger packets
than the ramips_main.c ethernet driver (ping stops going through
above "ping -s 1472" (1514 bytes), on the switch packets are recv_good until
"ping -s 1490", or about 1532 bytes).

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 33321
2012-09-05 20:08:42 +00:00
Gabor Juhos
6c7b776ae0 ramips: add rssileds to package set in profile for devices which got them.
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33316
2012-09-05 19:22:48 +00:00
Gabor Juhos
b0da5b73b8 ramips: add kmod-usb-ohci to defaults packages in profile of ALL5002
SVN-Revision: 33307
2012-08-29 10:37:51 +00:00
Gabor Juhos
54d8a55eed ramips: make built-in switch transparent for ALL0256N and ALL5002
This allows them to transparently communicate with an external VLAN switch.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33305
2012-08-29 10:37:47 +00:00
Gabor Juhos
bc4763a399 ramips: Power down phy on disabled switch ports
Power down phy on disabled switch ports.

Haven't measured this myself yet, but according to this
http://www.8devices.com/community/viewtopic.php?f=6&t=156
it can save about 300mW of power.

[juhosg: fix checkpatch warning]

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 33304
2012-08-29 10:37:45 +00:00
Gabor Juhos
1617f226a9 ramips: Add support for 8devices Carambola dev board.
Add support for 8devices Carambola dev board.

The Carambola is a small RT3050-based development board with two
ethernet ports, on-board chip antenna, usb and plenty of accessible
gpio ports, sold by 8devices.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 33303
2012-08-29 10:37:43 +00:00
Gabor Juhos
bb0785880a ramips: Rename POC registers
Rename POC registers.

The current code uses POC1-POC3.

The datasheet uses:
POC1: Port Control 0
POC1: Port Control 1
POC2: Port Control 2

So the first POC1 is a typo that should have been POC0, rename the
registers to POC0-POC2 accordingly.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 33302
2012-08-29 10:37:41 +00:00
Gabor Juhos
f1b9d77912 ramips: Minor ramips_esw.c cleanup
Stop handling VLAN setup in the kernel.
Removes the obsolete RT305X_ESW_VLAN_CONFIG_BYPASS option I added for
WL-351 and add some extra comments.
Also removes the en_vlan per-port flag that isn't very useful really, it now
is only controlled by the global enable_vlan flag.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 33301
2012-08-29 10:37:40 +00:00
Gabor Juhos
1f3400d3b4 ramips: Add switch setup to uci network defaults
Add switch setup to uci network defaults.

The 'lan' attribute is used to decide into which vlan to put the
port.
Currently 'disable' is never set, but the intention is to use this
for devices like the 8devices Carambola, which only has two ports
hooked up to the SoC.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 33300
2012-08-29 10:37:38 +00:00
Gabor Juhos
3b17f1deb8 ramips: Add swconfig support to ramips_esw.c
Add swconfig support to ramips_esw.c

This patch adds swconfig support for ramips_esw:

Tested on both D-LINK DIR-300 B1 and Sitecom WL-351 (external
rtl8366rb on internal port 5).
I've made sure that in the enable_vlan=0 case it behaves like a dumb
switch, so external switches should work fine with vlans and
verified this on the WL-351.

The current state shown by swconfig is always read directly from HW
registers, new settings only show after 'swconfig dev rt305x set apply'.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 33299
2012-08-29 10:37:36 +00:00
Gabor Juhos
358c7e47f2 ramips: ramips_esw.c indentation cleanup
Minor indentation cleanup.

Prepare for the main swconfig patch by cleaning up indentation a bit.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 33298
2012-08-29 10:37:35 +00:00
Gabor Juhos
cebaa557be ramips: fix board parameter for the NBG-419N (#12061)
SVN-Revision: 33229
2012-08-22 17:55:12 +00:00
Gabor Juhos
eb54a05e89 ramips: add profile for Allnet devices
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33225
2012-08-22 12:36:35 +00:00
Gabor Juhos
d77418d67e ramips: add RSSI leds for uci-defaults for ALL0256N
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33220
2012-08-22 09:46:30 +00:00
Gabor Juhos
67e6461ad7 ramips: add board alias for the ALL0239-3G
Generate image for the ALL0239-3G which can be flashed through the
chipset-vendor SDK based firmware's web-interface and bootloader.

The bootloader seems to ignore uImage checksum errors, but does complain about
them once the 0xDEADC0DE was replaced by an actual JFFS2 page.

I'm working on implementing fixtrx for uImage in the mtd package to solve this.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33206
2012-08-17 17:56:07 +00:00
Gabor Juhos
89606b61b1 ramips: add support for D-Link DIR-615 H1
rt2x00 still needs some patching as the radio doesn't come to life.
Installation via webflash.

[juhosg: fix whitespace issues, remove rt305x_register_usb
from machine setup because the board has no USB port]

Signed-off-by: Mikko Hissa <mikko.hissa@uta.fi>

SVN-Revision: 33205
2012-08-17 17:56:05 +00:00
Gabor Juhos
82759a1716 ramips: rename rt3352 usb platform devices
In order to get OHCI/EHCI working on the Rt3352, the platform device must be
named so rt3883-?hci will recognize it.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33145
2012-08-12 12:48:31 +00:00
Gabor Juhos
1525620b0e ramips: watchdog: use maximum possible timeout by default
As the userspace has no means to determine the maximum possible timeout, use
that as the default and let the userspace lower it when necessary.

As the result the usual OpenWrt install (with busybox's watchdog trying to set
the timeout to 60s on start) is using a 33s timeout on an RT3052 clocked at
384MHz instead of the current 20s default.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 33144
2012-08-12 12:48:28 +00:00
Gabor Juhos
615a619bc7 ramips: provide means to specify custom "image name" for uImages, use for DIR-620
D-Link's DIR-620 allows to flash a uImage directly from its web-interface but
for that the image name should be set to DIR_620.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 33143
2012-08-12 12:48:26 +00:00
Gabor Juhos
9365113040 ramips: add D-Link DIR-620 A1 support
Full functionality runtime tested, installation via OEM web-interface requires
a follow-up patch.

Thanks go to Sergey Vasilyugin for his patch that pointed me at the missing
bits (including the antiparallel wps led).

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 33142
2012-08-12 12:48:24 +00:00
Florian Fainelli
1627b2bb4b move rt305x-dwc driver to target specific modules.mk
SVN-Revision: 32864
2012-07-25 15:50:42 +00:00
John Crispin
5e52619b76 DWC otg usb: compilation fixes and trivial bugfix in slave mode
Signed-of-by: Nikolai Zhubr <n-a-zhubr@yandex.ru>

SVN-Revision: 32823
2012-07-24 20:38:55 +00:00
John Crispin
799d6deab0 D-Link DAP-1350 initial support
The initial support for the D-Link DAP-1350.
USB related functionality is not tested.

Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>

SVN-Revision: 32821
2012-07-24 20:38:43 +00:00
John Crispin
03be8d08ac initial LED configuration for Fonera 2.0n
Setup initial configuration for Wifi and USB LEDS of a Fonera 2.0n (ramips)

Signed-off-by: Malte Forkel <malte.forkel@berlin.de>

SVN-Revision: 32819
2012-07-24 20:38:31 +00:00
John Crispin
2d2479a033 add ALL5002 userspace support
detect EEPROM, MAC addresses and support sysupgrade for the ALL5002

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 32816
2012-07-24 20:38:14 +00:00
John Crispin
e219c3ac3a enable OHCI/EHCI glue on Rt305x, so it is available for Rt3352F.
Hope that this works, didn't have a chance to actually test it...

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 32815
2012-07-24 20:38:08 +00:00
John Crispin
a65eee9ac3 add image build for ALL5002
add image build for ALL5002

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 32814
2012-07-24 20:38:03 +00:00
John Crispin
0a08a776fb add support for Allnet ALL5002 to kernel
support ALL5002 in ramips/rt305x branch of the kernel.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 32813
2012-07-24 20:37:56 +00:00
John Crispin
6641024f50 uart_clk on Rt3352F is always 40MHz
Currently, sys_clk/10 is used which is just wrong.
cpu_clk/10 would work for systems with 400MHz CPU clock.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 32812
2012-07-24 20:37:50 +00:00
Gabor Juhos
372945185d ramips: rt305x: add support for Edimax 3G-6200N
Support for Edimax 3G-6200N router with USB.

Signed-off-by: Lukasz Golebiowski <lgolebio@gmail.com>

SVN-Revision: 32682
2012-07-12 13:29:46 +00:00
Vasilis Tsiligiannis
eee358338c ramips: mac address detection for Fonera 2.0n
Detect and apply MAC address of a Fonera 2.0n (ramips)

Signed-off-by: Malte Forkel <malte.forkel@berlin.de>
Signed-off-by: Vasilis Tsiligiannis <b_tsiligiannis@silverton.gr>

SVN-Revision: 32490
2012-06-23 13:58:29 +00:00
Gabor Juhos
833b4af816 ramips: rt305x: add support for the Petatel PSR-680W Wireless CDMA Router
This patch adds support for the Korean made Petatel PSR-680W Wireless CDMA Router.
The platform is based on Ralink RT3052.
http://wiki.openwrt.org/toh/petatel/psr-680w

Signed-off-by: Dmitry Shmygov <shmygov at rambler.ru>

SVN-Revision: 32450
2012-06-19 09:52:15 +00:00
John Crispin
a4d96aae8d bump to 3.3.8
SVN-Revision: 32055
2012-06-05 06:57:51 +00:00
Gabor Juhos
ffbb4f88a9 ramips: use the generic uci-default functions for initial LED setup
SVN-Revision: 31993
2012-05-29 16:39:18 +00:00
Gabor Juhos
c71838faa1 ramips: WAN LED for D-Link DIR-300-B1
Add led devices for D-Link DIR-300-B1 WAN LED.

Note that the GPIO state is also ANDed with the esw switch port 4
LED state, which is why I've set the amber LED to default-on.

Closes: https://dev.openwrt.org/ticket/11326

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

[ juhosg:
- fix comment style in mach-dir-300-revb.c,
- remove the PPP specific LED setup, not everyone uses a PPP connection
  on the WAN interface]

SVN-Revision: 31989
2012-05-29 16:39:03 +00:00
Gabor Juhos
1c552ba8e5 ramips: rt3883: add device registration code for the SPI controller
SVN-Revision: 31922
2012-05-27 17:10:00 +00:00
Gabor Juhos
9c241983fc ramips: allow to use the SPI driver on RT3662/RT3883
SVN-Revision: 31921
2012-05-27 17:09:58 +00:00
Gabor Juhos
78a750dcce ramips: rt3883: fix GPIO reservation for the SPI pins
SVN-Revision: 31920
2012-05-27 17:09:56 +00:00
Gabor Juhos
0622fdd82c ramips: rt305x: remove superfluous controller_data assignment
SVN-Revision: 31919
2012-05-27 17:09:52 +00:00
Gabor Juhos
7f5bec0642 ramips: make rt2x00 firmware extraction quiet
SVN-Revision: 31918
2012-05-27 17:09:50 +00:00
Gabor Juhos
2ae5581447 kernel: update linux 3.3 to 3.3.7
SVN-Revision: 31848
2012-05-23 21:05:32 +00:00
Gabor Juhos
e4720dfa95 ramips: Add byte queue limits support to net/ethernet/ramips_main.c
Add byte queue limits support to net/ethernet/ramips_main.c

"Byte queue limits are a mechanism to limit the size of the transmit
hardware queue on a NIC by number of bytes. The goal of these byte
limits is too reduce latency (HOL blocking) caused by excessive
queuing in hardware (aka buffer bloat) without sacrificing
throughput."

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 31844
2012-05-23 21:05:23 +00:00
Gabor Juhos
1d286fd755 ramips: Enable sysupgrade for Sitecom WL-351
Sysupgrade works just fine on my Sitecom WL-351 after adding this
oneliner.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 31843
2012-05-23 21:05:22 +00:00
Gabor Juhos
39994008cb linux: move certain disabled symbols to the generic configs
* CONFIG_ARCH_DMA_ADDR_T_64BIT
  * CONFIG_ARCH_HAS_ILOG2_U32
  * CONFIG_ARCH_HAS_ILOG2_U64
  * CONFIG_ARCH_PHYS_ADDR_T_64BIT
  * CONFIG_ARCH_SUPPORTS_MSI
  * CONFIG_GENERIC_CPU_DEVICES
  * CONFIG_HWMON_DEBUG_CHIP
  * CONFIG_I2C_PXA_PCI
  * CONFIG_LEDS_GPIO
  * CONFIG_MINIX_FS_NATIVE_ENDIAN
  * CONFIG_MLX4_CORE
  * CONFIG_POWER_SUPPLY
  * CONFIG_POWER_SUPPLY_DEBUG
  * CONFIG_QUOTACTL
  * CONFIG_SDIO_UART
  * CONFIG_SENSORS_K10TEMP
  * CONFIG_SENSORS_SCH56XX_COMMON
  * CONFIG_SENSORS_VIA_CPUTEMP
  * CONFIG_SERIO_AMBAKMI
  * CONFIG_SERIO_I8042
  * CONFIG_SERIO_LIBPS2
  * CONFIG_SERIO_PCIPS2
  * CONFIG_SERIO_RAW
  * CONFIG_SERIO_SERPORT
  * CONFIG_SPI_BITBANG
  * CONFIG_SPI_GPIO

SVN-Revision: 31737
2012-05-15 10:58:52 +00:00
Gabor Juhos
b472e5d12e kernel: update linux 3.3 to 3.3.6
SVN-Revision: 31709
2012-05-14 09:18:32 +00:00
Gabor Juhos
34018a630f kernel: update linux 3.3 to 3.3.5
SVN-Revision: 31645
2012-05-07 20:11:43 +00:00
Gabor Juhos
b0449ccf04 ramips: W306R V2.0 - GPIO and Network fixes
Fixed: GPIO typos and confirmed GPIO_BUTTON_RESET
Fixed: Lan & Wan reversed: swaped "eth0.2" with "eth0.1" by
       removing a line(default is correct), and reversed the
       Lan/wan layout LLLLW to WLLLL.

Added: image/Makefile now builds -factory.bin files. I am
       unsure of the accepted way to change the makefile but
       the name of the image needs to be 'linkn Kernel Image'
       in order to be accepted by the OEM firmware.

Known issue: eth0 (internal switch i think has mac address:
       00:11:22:33:44:55  but i think it should be same as
       the lan).
Known issue: Pressing the reset button has no noticable effect,
       i would expect the router to boot failsafe if being
       pressed on boot, reboot if short press and reset all
       to default if long press.

[juhosg: remove mtdlayout_W306R and use mtdlayout_4M instead]

Signed-off-by: David Pearce <david_18051985@hotmail.com>

SVN-Revision: 31557
2012-05-02 19:17:59 +00:00
Gabor Juhos
90e99b9fe8 ramips: Make serial console for DIR-300-B1 work again
Make serial console for DIR-300-B1 work again.

With some recent change, "console=ttyS1,57600" was removed from the
default kernel command line, this adds the necessary mkcmdline
incantation to image/Makefile to add it there for this target.
This is quite likely broken for other targets as well.

Without this the console switches to ttyS0 instead of ttyS1 and
kernel output is missing, and the userspace comes up with 9600 baud
instead of 57600.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>

SVN-Revision: 31556
2012-05-02 19:17:58 +00:00
Gabor Juhos
cbfce53831 kernel: update linux 3.3 to 3.3.4
SVN-Revision: 31541
2012-04-30 08:38:11 +00:00
Gabor Juhos
8e06682fb7 ramips: rt305x: extract wifi eeprom and use the 8M template for the UR-336UN
Patch-by: Lebedev Dmitry <lebedev@trendnet.ru>

SVN-Revision: 31507
2012-04-29 07:36:33 +00:00
Jonas Gorski
8fd383ae2e kernel: update linux 3.3 to 3.3.3
SVN-Revision: 31460
2012-04-24 09:25:38 +00:00
Gabor Juhos
1ab80c7817 ramips: rt305x: add support for the UR-336UN board
Patch-by: Lebedev Dmitry <lebedev@trendnet.ru>

SVN-Revision: 31451
2012-04-23 16:56:06 +00:00
Gabor Juhos
3626444c6d ramips: rt305x: add support for the Asus WL-330N3G board
This patch adds support for the ASUS WL-330N3G

Comparing to the WL-330N, It have 32MB ram, usb support and a bicolor led.

The bi-color led is driven by 2 gpio.
I don't know how to handle this, so I simply made 2 leds : one red, one blue.
But the red light takes precedence over the blue one according to the chart below.

r = led is red
b = led is blue
0 = led is off

xy= x->r for red, b for blue led, y->value of brightness in /sys/class/leds/x/brughtness

initial state	action	 led	gpio state

r0	b0	r0->r1	 r  	r0	b0
r0	b0	b0->b1   b	r0	b1

r1	b0	r1->r0	 0	r0	b0
r1	b0	b0->b1	 r	r1	*b1*

r1	b1	r1->r0   b	r0	b1
r1	b1	b1->b0   r	r1	b0

r0	b1	r0->r1   r	r1	*b1*
r0	b1	b1->b0   0	r0	r0

Signed-off-by: Frédéric Leroy <fredo@starox.org>

SVN-Revision: 31450
2012-04-23 16:56:05 +00:00
Gabor Juhos
5024ffb976 ramips: nuke 3.2 suport
SVN-Revision: 31405
2012-04-21 12:30:53 +00:00
Gabor Juhos
6c8ca78067 ramips: switch to 3.3.2
SVN-Revision: 31404
2012-04-21 12:30:51 +00:00
Gabor Juhos
5c325b0057 ramips: add support for 3.3
SVN-Revision: 31403
2012-04-21 12:30:50 +00:00
Gabor Juhos
7f902c962b ramips: rt305x: add OHCI/EHCI registration code for RT3352
SVN-Revision: 31402
2012-04-21 12:30:48 +00:00
Gabor Juhos
1645928135 ramips: rt305x: fix CPU clock detection on RT3352
SVN-Revision: 31401
2012-04-21 12:30:47 +00:00
Gabor Juhos
fb69e28eaf ramips: rt305x: use different memory size setup for RT3352
SVN-Revision: 31400
2012-04-21 12:30:45 +00:00
Gabor Juhos
818aeba960 ramips: rt3883: add profile and build sysupgrade image for the RT-N56U
SVN-Revision: 31399
2012-04-21 12:30:44 +00:00
Gabor Juhos
6b677e1d22 ramips: add swconfig to the default package list
SVN-Revision: 31398
2012-04-21 12:30:43 +00:00
Gabor Juhos
ced031a0b2 ramips: build initramfs image for the Fonera 2.0N
SVN-Revision: 31397
2012-04-21 12:30:42 +00:00
Gabor Juhos
fc88a363c0 ramips: rt305x: add initial support for Tenda W306R V2.0
More device info at: http://wiki.openwrt.org/toh/tenda/w306r

Signed-off-by: David Pearce <David_18051985@hotmail.com.au>
[juhosg: fix checkpatch errors, remove kmod-phy and luci-ssl packages
from the profile, change broken GPIO number]

SVN-Revision: 31396
2012-04-21 12:30:40 +00:00
Gabor Juhos
88b5827c52 ramips: remove hardcoded console parameter from kernel configs
SVN-Revision: 31395
2012-04-21 12:30:30 +00:00
Jonas Gorski
a8f2bc682e kernel: also update the targets to use 3.2.15
Thanks Gabor for spotting it.

SVN-Revision: 31337
2012-04-17 13:12:14 +00:00
Jonas Gorski
16b4cbcdd6 kernel: update linux 3.2 to 3.2.14
SVN-Revision: 31222
2012-04-09 14:48:51 +00:00
Jonas Gorski
d87efd8c3c kernel: update linux 3.2 to 3.2.13 and refresh patches
Also remove a duplicate patch from lantiq (already in generic).

SVN-Revision: 31158
2012-04-01 07:56:55 +00:00
Jo-Philipp Wich
e9c4d3d1f2 ramips: add support for the ARC FreeStation5 board, also fix WCR-150GN network setup while we're at it - thanks Pau Escrich <p4u@dabax.net> for the implementation
SVN-Revision: 31144
2012-03-29 16:03:04 +00:00
Gabor Juhos
d495277d9f ramips: rt305x: build image for the DIR-615 rev D boards
Patch from #10105.

SVN-Revision: 31101
2012-03-27 19:29:59 +00:00