Commit graph

2320 commits

Author SHA1 Message Date
Gabor Juhos
1374e5a721 ar71xx: rb91x: fix ethernet packet loss issues
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.

Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40509
2014-04-13 20:41:52 +00:00
Gabor Juhos
46a8af4c47 ar71xx/mikrotik: enable the AT803x PHY driver
It will be used on the RB91x boards.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40508
2014-04-13 20:41:51 +00:00
Gabor Juhos
02ea5b9e56 ar71xx: allow to configure AR803x PHYs via platform data
Add a patch for the at803x phy driver, in order to be able
to configure some register settings via platform data.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40507
2014-04-13 20:41:50 +00:00
Gabor Juhos
27dec09907 ar71xx: add phy_mmd_{read,write} helpers
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40506
2014-04-13 20:41:48 +00:00
Gabor Juhos
6a0f8ea201 ar71xx: enable console on the RB91x boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40505
2014-04-13 20:41:42 +00:00
Gabor Juhos
0d7197116e ar71xx: add profile and build image for the ZyXEL NBG6716 board
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: remove the non-existing zyxelnand subtarget specific stuff]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40502
2014-04-13 08:29:09 +00:00
Gabor Juhos
ecec091d33 ar71xx: add user-space support for the ZyXEL NBG6716 board
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40500
2014-04-13 08:29:07 +00:00
Gabor Juhos
a5e398abad ar71xx: add kernel support for ZyXEL NBG 6716
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot

Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
  - rename and refresh kernel patch,
  - fix a few typos,
  - change button key codes,
  - use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40499
2014-04-13 08:29:05 +00:00
Gabor Juhos
22916814e3 ar71xx: build firmware image for the WNDR3700 v4 board
Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40481
2014-04-12 20:22:41 +00:00
Gabor Juhos
a67578ce33 ar71xx/image: allow to use more arguments for some macros
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40480
2014-04-12 20:00:37 +00:00
Gabor Juhos
4149ab5193 ar71xx: wndr4300: indicate WNDR3700v4 in the kernel support files
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40479
2014-04-12 19:58:23 +00:00
Gabor Juhos
7b85e2e527 ar71xx: wndr4300: enable 5V power for the USB port
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.

Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40478
2014-04-12 19:58:20 +00:00
Gabor Juhos
ed72141fd4 ar71xx: wndr4300: use KEY_RFKILL code for the Wireless button
Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40477
2014-04-12 17:53:34 +00:00
Gabor Juhos
b971a4b5b9 ar71xx: add default LED config for WiFi LEDs on the WNDR4300
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40476
2014-04-12 17:42:36 +00:00
Gabor Juhos
4fe71cedfe ar71xx: wndr4300: add LED for 2.4Ghz wifi interface
Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40475
2014-04-12 17:42:35 +00:00
Gabor Juhos
db123a8a21 ar71xx: wndr4300: select GPIO_OUT functionality for LED GPIOs
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40474
2014-04-12 17:42:34 +00:00
Gabor Juhos
9b7b57aeb4 ar71xx: wndr4300: change 'orange' to 'amber' in LED color names
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.

Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40473
2014-04-12 17:42:33 +00:00
Gabor Juhos
a93c87d772 ar71xx: fix typos in TP-Link rssileds definition
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5109/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40472
2014-04-12 16:01:45 +00:00
Gabor Juhos
087547d3e2 ar71xx: add rssileds for Ubiquiti XM boards
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40471
2014-04-12 16:01:43 +00:00
Gabor Juhos
d2812cb036 kernel: update 3.10 to 3.10.36
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40467
2014-04-12 11:59:07 +00:00
Gabor Juhos
17f848538c ar71xx: fix image generation
Move the comments out from the shell script to fix build
breakage introduced in r40464.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40466
2014-04-12 11:59:05 +00:00
Gabor Juhos
cd75606712 ar71xx: avoid spurious restarts caused by the watchdog on AR934x
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40465
2014-04-12 10:21:04 +00:00
Gabor Juhos
fd53cfa31b ar71xx: add comments for image Makefile.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5075/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40464
2014-04-12 09:52:58 +00:00
Gabor Juhos
1bce5e8328 ar71xx: initial support for TP-Link Archer C7v2
The C7v2 has 16 MB flash and QCA9880-BR4A rev 2 supported by ath10k driver.
The C7v1 had 8 MB flash and the unsupported QCA9880-AR1A rev 1.

Signed-off-by: Adam Serbinski <adam@serbinski.com>
Patchwork: http://patchwork.openwrt.org/patch/5071/
[juhosg:
 - remove the v2 specific profile add the ath10k driver to the existing
   Archer C7 profile instead. Although on v1 devices it does not change
   the non-working behaviour, but the ath10k driver is useful for users
   whom have replaced the wifi card with a supported one in their units.
 - update image/Makefile to build firmware image for both boards if the
   Archer C7 profile is selected]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40463
2014-04-12 09:52:54 +00:00
Felix Fietkau
8be7f487e2 ar71xx: move some always-used led related functionality from kmod packages to the kernel image
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40413
2014-04-07 10:44:52 +00:00
Felix Fietkau
4a9ea80ef0 /lib/functions.sh: move rarely used mtd and macaddr related functions to /lib/functions/system.sh
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40411
2014-04-07 10:29:47 +00:00
Felix Fietkau
7131a104f5 ar71xx: add support for the TP-LINK TL-WR841N/ND v9
Everything seems to be working fine. Potential issues:

* VLAN port IDs are reversed with regard to the numbers on the case.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 40400
2014-04-07 08:00:02 +00:00
Felix Fietkau
f80f0c7d22 ar71xx: add support for QCA953x SoC
I don't have access to the specs, so I'm not sure about every detail, but I
haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty
much like a QCA955x without PCI, a little twist in the clock calculation and
a AR9331-compatible switch.

Features not yet supported:

* EHCI (my test system doesn't have USB)
* ? (I have no idea if the QCA953x has any other features I don't know about
that aren't used by the TL-WR841N v9)

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 40399
2014-04-07 07:59:45 +00:00
Gabor Juhos
627baa28d3 kernel: update 3.10 to 3.10.34
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40291
2014-03-27 09:28:33 +00:00
Gabor Juhos
b68564ed3f ar71xx: build image for TL-WDR4300v1 (IL)
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.

Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40038
2014-03-27 06:36:59 +00:00
Gabor Juhos
4ea54b827f ar71xx: add profile and build firmware image for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40036
2014-03-27 06:36:57 +00:00
Gabor Juhos
02f2e90d5f ar71xx: add user space support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: use correct board name in uci-defaults/02_network]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40033
2014-03-27 06:36:47 +00:00
Gabor Juhos
5256bbdc56 ar71xx: add kernel support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
 - use a separate patch for kernel changes,
 - reorder Kconfig and Makefile entries,
 - change function and variable names to be lowercase only
   and fix misaligned tabs in mach-gs-oolite.c,
   ... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40032
2014-03-27 06:36:46 +00:00
Gabor Juhos
f0dc89b46f ar71xx: rename RB951Ui specific kernel patch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40031
2014-03-27 06:35:55 +00:00
Gabor Juhos
47dfbb5bc6 ar71xx: rb95x: use correct SPI flash address
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.

Compile tested only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39891
2014-03-12 12:52:39 +00:00
Gabor Juhos
25e870eed6 ar71xx: ar934x_nfc: fix memory initialization bug
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type)  * array_size   should be used in memset.

Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39890
2014-03-12 12:52:36 +00:00
Felix Fietkau
802d17ceaf ar71xx: Add 16MB Flash version for Embedded Wireless Dorin Platform
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>

SVN-Revision: 39764
2014-02-28 11:08:14 +00:00
Felix Fietkau
d83750083d ar71xx: adjust ew-dorin platform for LAN+WAN setup
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>

SVN-Revision: 39763
2014-02-28 11:08:04 +00:00
Gabor Juhos
e9c80a1224 ar71xx: fix failsafe acces on several devices
The ar71xx platform always uses the eth0 interface to provide
access to the device in failsafe mode. Due to this, failsafe
access is broken on devices where the LAN ports are connected
to the 'eth1' interface.

Update the relevant script to correctly set the ifname variable
for these devices.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39752
2014-02-25 17:40:04 +00:00
Gabor Juhos
f677b1bc7e kernel: update 3.10 to 3.10.32
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39707
2014-02-23 10:59:40 +00:00
Gabor Juhos
590bafe3de ar71xx: define status LED for the RB91x boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39705
2014-02-23 08:11:54 +00:00
Gabor Juhos
da2f3c1448 ar71xx: rb91x: register GPIO LEDs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39704
2014-02-23 08:11:53 +00:00
Gabor Juhos
14d95026b2 ar71xx: rb91x: add SPI device for the serial shift register
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.

Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39703
2014-02-23 08:11:52 +00:00
Gabor Juhos
7b89005f0d ar71xx/mikrotik: enable the 74x164 GPIO driver
That will be used to drive the 74HC595 serial-in/parallel-out
8-bits shift register which can be found on some RouterBOARDs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39702
2014-02-23 08:11:50 +00:00
Gabor Juhos
5f224ef8a3 ar71xx: improve platform device support in the gpio-74x164 driver
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39701
2014-02-23 08:11:49 +00:00
Gabor Juhos
3d906ac6ac ar71xx: rb91x-nand: rewrite to use GPIO API
Rewrite tha rb91x-nand driver to use GPIO API to
modify the NAND control lines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39700
2014-02-23 07:19:32 +00:00
Gabor Juhos
8fea668cb7 ar71xx: rb91x: register a gpio-latch platform device
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39699
2014-02-22 18:05:32 +00:00
Gabor Juhos
da5caba072 ar71xx/mikrotik: enable the GPIO latch driver
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39698
2014-02-22 18:05:31 +00:00
Gabor Juhos
ab08c40487 ar71xx: add a generic GPIO latch driver
It will be used for the Mikrotik boards.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39697
2014-02-22 18:05:29 +00:00
Gabor Juhos
be18a3849b ar71xx/mikrotik: enable small sector erase in the m25p80 driver
The serial flash devices used on the ROuterBOARDs are
supporting 4KiB erase blocks. Enable the small sector
erase option in the m25p80 driver to avoid superfluous
erase/write of adjacent blocks.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39696
2014-02-22 16:26:55 +00:00