The GPIO buttons of ARV752DPW are active low.
Treating them as active high caused a reboot loop as a reset-button
press is detected by gpio-button-hotplug/gpio-keys-polled on startup.
This fixes: https://dev.openwrt.org/ticket/12642
Signed-off-by: Rafael Gieschke <rafael@gieschke.de>
SVN-Revision: 36783
On linux 3.8 the switch is named as "switch0", but the network configuration script names it as "eth0", causing no communication over ethernet due to no proper VLAN config.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 36782
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36781
This patch is a device tree enhancement that IMHO is worthy of mainline.
It allows the bootloader's commandline to be preserved even when the
device tree specifies one.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36780
This patch enables retrieving the wifi calibration data from an MTD
partition. It requires the previous patch.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36779
This postpones the initialization of PCI and wifi until after the MTD
initialization, so that calibration data may be loaded from there.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36778
This reassigns the PPPoE status to the LED that was intended to indicate
it, rather than the DSL sync light.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36777
At offset 0x40, signature for TL-MR10U/TL-MR11U begin
from 0x00, not 0x10/0x11.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36727
MR10U is closer to MR3040 than WR703N. This changes also
enable USB power on GPIO18.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36726
Tested on Buffalo WZR-600DHP with ar8316 switch. Commands used to mirror both
RX and TX traffic from LAN port 1 to LAN port 4:
$ swconfig dev switch0 set enable_mirror_rx 1
$ swconfig dev switch0 set enable_mirror_tx 1
$ swconfig dev switch0 set mirror_monitor_port 4
$ swconfig dev switch0 set mirror_source_port 1
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 36713
* update the bootcode.bin to the newest version
- gpu/cpu mem split is now configured through config.txt, so no need
to create more than one sd card image (just edit the config.txt)
- bootcode.bin now supports the never revision 2 raspberry pis
* add a commented prepopulated config.txt for easier config changes
Taken from <https://github.com/Evilpaul/RPi-config>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36668
Check bootloader argument in mtd.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo@openwrt.org: split into two patches, one for detection,
one letting bcm63xxpart use it.]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36659
Don't build the CRAMFS file system module in the kernel, and save some bytes.
No bcm63xx board needs this obsolete file system, neither those ones using
the Redboot bootloader (liveboxes). Thus, there is no need to build it, since it has
been replaced long time ago by squashfs.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 36616
zsmalloc was changed to a bool because of missing exports in the kernel,
but we already export the required symbol, so change it back to tristate.
Closes#13481.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36587
This allow us to increase the kernel partition size,
and ensures, that the -factory image still usable via
the original interface.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36584
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36580
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36579
Here is corrected version (only thing not working are wifi LEDs).
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36578
