This is required to update bcma without build breakage. One of bcma
patches changes BCMA_SFLASH dependency.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Specifying the device profile in PROFILES is unnecessary, and for all
devices the DEVICE_PROFILE variable matched the device name.
Get rid of this useless variable and set DEVICE_DTS to $(1)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The network defaults for the WZR-HP-G300NH and CR3000 models wrongly set the
lan interface to a vlan tagged device while the switch was set up in untagged
mode, leading to broken lan side ethernet connectivity by default.
Fix the issue by emitting untagged interfaces, consistent with the switch
setting on the device.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
On UBI-enabled devices using squashfs as their rootfs an error
message like
UBIFS error (ubi0:3 pid 1): init_constants_early: too few LEBs (12), min. is 17
was thrown while probe-mounting the rootfs which later on succeeds and
thus shouldn't alert the user.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A bug resulting in the NAND not being detected by newer kernels has
kept me sleepless for months and yet I wasn't able to discover the
cause.
Bring back patches and files for 4.1 until this has been resolved.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use kernel config as input instead of -march CFLAGS.
With this change, -march can be dropped and replaced with more specific
optimization flags for better code generation.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We call all commands normally, with standard echoing. It's useful for
debugging with V=s. Don't make lzma compression an exception, it's a bit
confusing this way.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers
Default configuration:
- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space
Flash instruction (do it under U-Boot, using RS232):
1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
