Tama Electric Axing W06 is a 2.4 GHz band 11n router, based on Mediatek
MT7688AN.
Specification:
- MT7688AN (575 MHz)
- 64 MB of RAM (DDR2 SDRAM)
- 16 MB of Flash (SPI)
- 1T1R 2.4 GHz
- 1x 10/100/1000 Mbps Ethernet
- 4x LEDs (GPIO connected: 3), 1x button
- 1x USB 2.0 Type-A (host)
- UART header on PCB (GND, RX, TX, Vcc from RJ45 side)
Flash instruction using sysupgrade image:
1. Connect micro-USB cable for power supply into W06 and turn on the
router
2. Connect to wifi with SSID "tama-*" with password. Complete SSID and
password are listed on the back of the router
3. Access to 192.168.1.1 and login with user name "admin" and password
empty
4. In firmware update（ファームウェア更新） page, click "参照" button
and click "ブラウザー" button to open file browser, select the
sysupgrade image and press OK button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use the generic board detection for the GnuBee Personal Cloud Two
instead of the target specific one as all recent additions are doing.
Fixup the pinmux to set all pins used as GPIO to the function GPIO.
Request pins where used.
Drop the i2c from the dts. There is nothing connected. While at it fix an
indentation issue and use references instead of duplicating the whole
node path.
Use the same switch config as for the GB-PC1 and drop the led trigger for
the not supported IP1001 phy connected to second rgmii.
Fixes: c60a21532b ("ramips: Add support for the GnuBee Personal Cloud Two")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the generic board detection for the D-Link DAP-1522 A1 instead of the
target specific one as all recent additions are doing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Updated the devicetree source files to make use of the following
upstreamed drivers:
- xrx200 ethernet phy
- reset controller unit
- dwc2
- fpi
Use our custom xrx200 ethernet phy compatible to support boards, which
have switched the vr9 revision during lifetime, with a single devicetree
source file.
By switching to the dwc2 driver + usb phy framework, we don't need to used
our custom gpio power patch and can use a fixed regulator instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
On danube the USB0 registers are at 1e101000 similar to all other lantiq
SoCs.
On Danube and AR9 the USB core is connected to the AHB bus, hence we need
to enable the AHB Bus as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add a custom xrx200 ethernet phy compatible to load the firmware matching
the vr9 revision without specifing an expected revision.
We have quite a few boards in the tree were later produced ones are using
a more recent vr9. It is impossible to distinguish which revision of the
vr9 is used without opening the case and removing a heatsink for some of
them.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts kernel commit 1eed40043579 ("MIPS: smp-mt: Use CPU interrupt
controller IPI IRQ domain support"). With the patch applied, the kernel
hangs during boot if SMP is active.
The Lantiq IRQ controller gets registered first and it directly handles
the MIPS native SW1/2 and HW0 - HW5 IRQs. It looks like this controller
already registers IRQ 0 - 7 and the generic driver only gets the following
IRQs starting later.
The upstream discussion can be found at
https://www.linux-mips.org/archives/linux-mips/2017-05/msg00059.html.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This just copies the patches, configuration and dts files into the
directories hich are used for kernel 4.14.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is fixing multiple compile problems with kernel 4.14 and updates the
code to take care of changes introduced between kernel 4.9 and 4.14.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the devicetree source files to a kernel specific directory in
preparation of adding kernel 4.14 support.
Rename the subtarget kernel config files to match a specific kernel
version.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rename the gphy firmware to match the name requested by kernel 4.14 and
update the devicetree source files to use the new name.
Update the u-boot lantiq Makefile to be compatible with the new names as
well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With upstream commit 2c93e790e825 ("usb: add CONFIG_USB_PCI for system
have both PCI HW and non-PCI based USB HW") the CONFIG_USB_PCI was
introduced.
The option is disabled by default in our generic kernel 4.14 config, hence
we need to set the option for all related kernel modules.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With a9772285a724 ("linux/compiler.h: Split into compiler.h and
compiler_types.h") compiler.h was refactored and most its content was
moved to compiler_types.h. Both files are required to build ppp-mod-pppoa.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add support to allow for per switch port VLAN priority (PCP) bits
for the ar8327/8337 chip using the swconfig utility.
Tested on Netgear R7800
Signed-off-by: Tan Hong Hui <hhtan72@yahoo.com>
The current implementation only checked if uqmi itself executed
correctly which is also the case when the returned value is actually
an error.
Rework this, checking that CID is a numeric value, which can only
be true if uqmi itself also executed correctly.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This issue is also present in kernel 4.9 starting from 4.9.71
Adapted the patch, as the fixed function is in another location here.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
When using pigz, a parallel gzip implementation, the gzip step in the
image build for some targets fails, because the image filename already
has the .gz extension. This results in an emtpy image file. Fix this by
adding the --force option to gzip in the Build/gzip macro.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Martin Schleier <drahemmaps@gmx.net>
This reverts commit 6c2e1ff80f.
GNU gzip does not fail when the image filename already contains the .gz
extension, this is a problem specific to pigz. Revert the commit, as we
now gzip the image twice.
Reported-by: Martin Schleier <drahemmaps@gmx.net>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
1721453 Remove special handling of A-for-A queries.
499d8dd Fix boundary for test introduced in 3e3f1029c9ec6c63e430ff51063a6301d4b2262
6f1cbfd Fix debian/readme typo.
55ecde7 Inotify: Ignore backup files created by editors
6b54d69 Make failure to chown() pidfile a warning.
246a31c Change ownership of pid file, to keep systemd happy.
83e4b73 Remove confusion between --user and --script-user.
6340ca7 Tweak heuristic for initial DNSSEC memory allocation.
baf553d Default min-port to 1024 to avoid reserved ports.
486bcd5 Simplify and correct bindtodevice().
be9a74d Close Debian bug for CVE-2017-15107.
ffcbc0f Example config typo fixes.
a969ba6 Special case NSEC processing for root DS record, to avoid spurious BOGUS.
f178172 Add homepage to Debian control file.
cd7df61 Fix DNSSEC validation errors introduced in 4fe6744a220eddd3f1749b40cac3dfc510787de6
c1a4e25 Try to be a little more clever at falling back to smaller DNS packet sizes.
4fe6744 DNSSEC fix for wildcard NSEC records. CVE-2017-15107 applies.
3bd4c47 Remove limit on length of command-line options.
98196c4 Typo fix.
22cd860 Allow more than one --bridge-interface option to refer to an interface.
3c973ad Use SIGINT (instead of overloading SIGHUP) to turn on DNSSEC time validation.
faaf306 Spelling fixes.
c7e6aea Change references to gPXE to iPXE. Development of EtherBoot gPXE was always development of iPXE core developer Michael Brown.
e541245 Handle duplicate RRs in DNSSEC validation.
84a01be Bump year in Debian copyright notice.
d1ced3a Update copyrights to 2018.
a6cee69 Fix exit code from dhcp_release6.
0039920 Severely fix code formating of contrib/lease-tools/dhcp_release6.c
39d8550 Run Debian startup regex in "C" locale.
ef3d137 Fix infinite retries in strict-order mode.
8c707e1 Make 373e91738929a3d416e6292e65824184ba8428a6 compile without DNSSEC.
373e917 Fix a6004d7f17687ac2455f724d0b57098c413f128d to cope with >256 RRs in answer section.
74f0f9a Commment language tweaks.
ed6bdb0 Man page typos.
c88af04 Modify doc.html to mention git-over-http is now available.
ae0187d Fix trust-anchor regexp in Debian init script.
0c50e3d Bump version in Debian package.
075366a Open inotify socket only when used.
8e8b2d6 Release notes update.
087eb76 Always return a SERVFAIL response to DNS queries with RD=0.
ebedcba Typo in printf format string added in 22dee512f3738f87539a79aeb52b9e670b3bd104
0954a97 Remove RSA/MD5 DNSSEC algorithm.
b77efc1 Tidy DNSSEC algorithm table use.
3b0cb34 Fix manpage which said ZSK but meant KSK.
aa6f832 Add a few DNS RRs to the table.
ad9c6f0 Add support for Ed25519 DNSSEC signature algorithm.
a6004d7 Fix caching logic for validated answers.
c366717 Tidy up add_resource_record() buffer size checks.
22dee51 Log DNS server max packet size reduction.
6fd5d79 Fix logic on EDNS0 headers.
9d6918d Use IP[V6]_UNICAST_IF socket option instead of SO_BINDTODEVICE for DNS.
a49c5c2 Fix search_servers() segfault with DNSSEC.
30858e3 Spaces in CNAME options break parsing.
Refresh patches.
Remove upstreamed patches:
250-Fix-infinite-retries-in-strict-order-mode.patch
260-dnssec-SIGINT.patch
270-dnssec-wildcards.patch
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Support for kernel 4.14 was added 2 months ago, make it now the default
kernel to use for the x86 target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stijn Segers <francesco.borromini@inventati.org>
The default receive window size in dropbear is hardcoded to 24576 byte
to limit memory usage. This value was chosen for 100Mbps networks, and
limits the throughput of scp on faster networks. It also severely limits
scp throughput on high-latency links.
Add an option to set the receive window size so that people can improve
performance without having to recompile dropbear.
Setting the window size to the highest value supported by dropbear
improves throughput from my build machine to an APU2 on the same LAN
from 7MB/s to 7.9MB/s, and to an APU2 over a link with ~65ms latency
from 320KB/s to 7.5MB/s.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The gzip step in the sdcard image build fails because the image filename
already has the gzip extension. This results in an empty image file, to
which the metadata is finally appended.
Remove the .gz extension from the image filename to fix this.
Fixes: e79b096ee1 ("brcm2708: convert to metadata")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
In the initial patch which adds HSDK board there were no update
of network configuration scripts. Without it by default static IP
is set for br-lan and there is no access to internet.
This patch fixes the issue.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
CC: Alexey Brodkin <abrodkin@synopsys.com>
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John Crispin <john@phrozen.org>
