Function register_mtd_parser always returned 0 (at least since v3.3)
before being changed to return void in v3.14-rc1~65^2~93 (mtd: make
register_mtd_parser return void), so it's not needed to check the
return value of this function. Also add __init flag to caller.
This fix compile errors in 3.14 kernel like:
drivers/mtd/mtdsplit_seama.c: In function 'mtdsplit_seama_init':
drivers/mtd/mtdsplit_seama.c:99:2: error: void value not ignored as it ought to be
return register_mtd_parser(&mtdsplit_seama_parser);
^
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40731
This patch adds port status information and MIB counters to the ADM6996
switch driver.
The driver supports also the older ADM6996L-variant, but I'm not able to
test this patch on that chip. According to the datasheet the same
registers exist there as well, so I think it should work, but any
feedback is appreciated.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40542
If the CPU port is not forced up, the link, at least on this board, is lost after
changes are applied. This makes sure that the link is restored. Regression tests
should confirm it doesn't break other boards.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40305
- hide port pvid - vlan index relation
- switch initialises with vlans disabled so port isolation is not used
- remove special treatment of cpu port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40304
Changes to:
- show the correct "enable_vlan" value under "Global attributes"
- show tagged ports under "Vlan: ports"
- use get_port_link method to report link status
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40303
Use the 'swconfig_trig_set_brightness' function to set
the brightness value of the LED when the link goes down.
This ensures that the last brighness value is saved into
a local variable which is used to track the actual LED
status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39402
This reverts r38197.
The automatically created firmware partition includes
the partition_table partition. Apart from the partition
table, this partition contains sensitive data on some
Compex devices which data can be destroyed when the
firmware partition gets modified. Revert the change to
prevent that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39382
This patch enables jumbo frames on AR8327 switch by default.
I have tested it on TP-Link TL-WDR3600.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39076
This patch is needed to use the switch inside the Sitecom WLR-8100;
it was unusable and detected as Generic-Phy before.
since ar8337 is behaving like ar8327
generally do the same thing
see: https://forum.openwrt.org/viewtopic.php?pid=214218#p214218
forward-ported to trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4469/
[juhosg: merge chip_is_ar83[23]7 statements in ar8xxx_phy_config_init]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38952
The BCM5365 needs a shift of 7 bits and not 6 bits like the BCM5325 for
the untagged ports.
Thank you Russell for reporting this and testing the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38793
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
The GPIO bit banging protocol implementation was copied from the old
switch driver and adapted to this driver and changed to the mainline
kernel GPIO interface.
The ADM6996L is different from the ADM6996M which is supported, for
both specs are available in the Internet.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38698
The revision is stored in a different register than it is in other
Broadcom switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37995
These switches are integrated in some recent BCM53XX and BCM47XX SoCs
like the BCM53572.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37994
The Linksys wrt310n v1 does not have a robo_reset config variable in
nvram, but GPIO Pin 8 is the pin needed for resetting the external
switch, Linksys hard coded it into their source code.
Thank you Devastator for testing.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37988
BCM5365 (and probably other older variants) use a different phy id, so
the phy driver never attached for them.
Fix this by adding the appropriate phy id to the fixup and the phy
driver.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37906
b53_no_ops has no elements and b53_port_ops has one element, this makes
the code access some random memory when trying to access the mib
counter functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37895
The myloader partition parser code uses ifdef wrappers
to make the code usable on kernels below version 3.2.
All targets are using kernel 3.3 at least so the wraper
is not needed. Remove that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37880
This is needed for some switches used on bcm47xx SoCs like the one on the Asus RT-N66U.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37645
There is no platform using the gpio-pwm driver, yet these patches break the
generic PWM framework that is in upstream. So just remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 37490
It hasn't been buildable for a long time, and there are no users of it
anymore left as all of them have been switched to the upstream accepted
version.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37436
