This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 42897
This change makes the profile of WDR4900 more consistent with other router
specific profiles.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
SVN-Revision: 42896
Error reported by buildbot:
Package kmod-at91-adc is missing dependencies for the following libraries:
input-core.ko
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 42893
7Links PX-4885 (clones) can also be purchased with 8MB flash.
Creating images for these routers, use dtsi for common part
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42892
DT file doesn't include any GPIOs yet, but let's add it as we got some
interest in this device on IRC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42864
This allows IPv6 to set up without IPv4 being up thus
IPv6-only or IPv6+DS-Lite working with the default config.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42848
Have gpio driver adopt irqdomain support so that there are
non-overlapping allocations of irq numbers mapped to gpio's.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 42844
This patch originally failed to combine INTA/B/C/D onto a single ARM CPU
interrupt. Instead, it mapped INTA/B/C and excluded D. This patch
corrects the issue by mapping all four interrupts to the single ARM CPU
interrupt. The original intent of the patch still holds as the newer PCB
take advantage of isolated interrupts. This fix only applies to older
PCB's that do not route INTA/B/C/D to unique external ARM CPU
interrupts.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 42830
Looks like the targets are Ubiquiti routers which don't come with any wireless cards.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 42810
the driver did not handle all states correctly causing a deadlock of the i2c hw block.
Signed-off-by: Ing.Michele Mogioni <michele.mogioni@unimc.it>
SVN-Revision: 42807
This enables dedicated "rootfs" splitter by default. We still keep
CONFIG_MTD_SPLIT_SQUASHFS_ROOT, so the old (built-in) splitter will be
used as a fallback in case of problems.
Once we decide the dedicated partitioner works stable, we should remove
the old one completely.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42805
All TP-LINK machine names begin with "TP-LINK", so there's no need to check for
more specific model names. This also allows adding new models like the Archer
series more easily.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42795
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.
Signed-off-by: Ron Curry <wingspinner@gmail.com>
SVN-Revision: 42785
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".
Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42782
